oil TOYOTA AVENSIS 1999 Supplement

MX02G–03
Z17558
GasketO–Ring
Oil Strainer
Oil Pump Driven Rotor
Oil Pump Drive Gear Oil Pump Drive Rotor
Oil Pump Cover Spring Holder Spring Ball Relief Valve Transmission Oil Pump
Case
N·m (kgf·cm, ft·lbf): Specified torque

Non–reusable part
10 (105, 8)
10 (105, 8)



MX–38
– MANUAL TRANSAXLE (E251)OIL PUMP
OIL PUMP
COMPONENTS

MX02H–02
Z00242
Z00243
Z00244
– MANUAL TRANSAXLE (E251)OIL PUMP
MX–39
INSPECTION
1. CHECK ROTOR BODY CLEARANCE
(a) Install the oil pump drive gear to the drive rotor.
(b) Using a feeler gauge, measure the body clearance be-
tween the drive rotor and oil pump case.
Standard clearance:
0.10 – 0.16 mm (0.0039 – 0.0063 in.)
Maximum clearance:
0.30 mm (0.0118 in.)
2. CHECK ROTOR TIP CLEARANCE
(a) Install the oil pump drive gear to the drive rotor.
(b) Using a feeler gauge, measure the tip clearance between
the drive and driven rotors.
Standard clearance:
0.08 – 0.15 mm (0.0031 – 0.0059 in.)
Maximum clearance:
0.30 mm (0.0118 in.)
3. CHECK SIDE CLEARANCE
Using a precision straight edge and feeler gauge, measure the
side clearance of both rotors.
Standard clearance:
0.03 – 0.08 mm (0.0012 – 0.0031 in.)
Maximum clearance:
0.15 mm (0.0059 in.)

MX02I–03
Q06217
Shift Interlock Plate
Transmission Oil Baffle Shift Interlock Plate
No.1 Compression SpringControl Shaft Cover
Oil Seal
Snap Ring
No.1 Select Spring Seat
Slotted Spring Pin
No.1 Shift Inner Lever
Shift and Select Lever Shaft Snap Ring
Non–reusable partNo.2 Select Spring SeatNo.2 Compression SpringNo.2 Shift Inner LeverSlotted Spring Pin
Apply MP grease

Dust Boot

MX–40
– MANUAL TRANSAXLE (E251)SHIFT AND SELECT LEVER SHAFT
SHIFT AND SELECT LEVER SHAFT
COMPONENTS

MX060–02
D06656
Differential Spider
Differential Pinion
Differential Side Gear
Side Gear Thrust
Washer
Pinion Thrust Washer

Tapered Roller Bearing
and Outer Race
Differential Right Case Vehicle Speed Sensor Drive Gear
Differential Left Case

Tapered Roller Bearing
and Outer Race Ring Gear
Oil Baffle

Oil Seal x16
Shim
Oil Seal
63 (640, 46)
N·m (kgf·cm, ft·lbf): Specified torque

Non–reusable partx16
124 (1,260, 91)
– MANUAL TRANSAXLE (E251)DIFFERENTIAL CASE
MX–41
DIFFERENTIAL CASE
COMPONENTS

Z00284
Z00286
Z00288
SST
Z00289
– MANUAL TRANSAXLE (E251)DIFFERENTIAL CASE
MX–43
(d) Remove the 2 differential side gears, side gear thrust
washers, 4 differential pinions and pinion thrust washers
from the differential left case.
5. Transmission Case Side:
IF NECESSARY, REPLACE OIL SEAL AND TAPERED
ROLLER BEARING OUTER RACE
(a) Using a screwdriver, remove the oil seal.
(b) Remove the oil baffle.
(c) Using a brass bar and hammer, drive out the bearing out-
er race lightly and evenly.
(d) Remove the shim.
(e) Install the shim.
(See page MX–41)
HINT:
First select and install a shim of lesser thickness than before.
(f) Using SST and a press, install a new tapered roller bear-
ing outer race.
SST 09316–60011 (09316–00011, 09316–00041)
(g) Install the oil baffle.
HINT:
Install the oil baffle projection into the case side cutout.

Q06288
SST
N00100
SST
Z00292
SST
Z00293
SST MX–44
– MANUAL TRANSAXLE (E251)DIFFERENTIAL CASE
(h) Using SST and a hammer, drive in a new oil seal.
SST 09223–15020, 09950–70010 (09951–07150)
(i) Coat the lip of oil seal with MP grease.
6. Transaxle Case Side:
IF NECESSARY, REPLACE OIL SEAL AND TAPERED
ROLLER BEARING OUTER RACE
(a) Using a screwdriver and hammer, drive out the oil seal
from the transaxle case.
(b) Using SST, pull out the tapered roller bearing outer race.
SST 09612–65014
(c) Using SST and a press, install a new tapered roller bear-
ing outer race.
SST 09316–60011 (09316–00011, 09316–00041)
(d) Using SST and a hammer, drive in a new oil seal.
SST 09316–60011 (09316–00011)
(e) Coat the oil seal lip with MP grease.

Z00295
MX09B–01
Z00296
Z00297
D06655
Matchmarks
– MANUAL TRANSAXLE (E251)DIFFERENTIAL CASE
MX–45
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
reassembly.
1. ASSEMBLE DIFFERENTIAL CASE
(a) Install the thrust washer to the side gear.
(b) Install the 4 pinions and thrust washers to the spider.
(c) Install the side gear and spider with the 4 pinions to the
differential left case.
(d) Using a dial indicator, measure the backlash of the pinion
gear while holding the differential left case.
Standard backlash: 0.05 – 0.20 mm (0.0020 – 0.0079
in.)
HINT:
Push the pinion gear and spider with the 4 pinions to the differ-
ential left case.
(e) Install the side gear and spider with the 4 pinions to the
right side of the differential case. Check the side gear
backlash.
(f) Refer to the table below, select the thrust washer which
will ensure that the backlash is within the specification.
Try to select a washer of the same size.
Thickness mm (in.)Thickness mm (in.)
0.80 (0.0315)1.20 (0.0472)
0.90 (0.0354)1.30 (0.0512)
1.00 (0.0394)1.40 (0.0551)
1.10 (0.0433)–
(g) Align the matchmarks on the differential cases.
(h) Using a plastic hammer, carefully tap the differential case
to install it.
(i) Using a torx wrench (T50), install and torque the 16 torx
screws.
Torque: 63 N·m (640 kgf·cm, 46 ft·lbf)
2. INSTALL RING GEAR
(a) Clean the contact surface of the differential case and the
threads of the ring gear and differential case.

SA10A–02
FA1535
SST
F02688
F02721
F02724
– SUSPENSION AND AXLEFRONT DRIVE SHAFT
SA–3
REMOVAL
NOTICE:
The hub bearing could be damaged if it is subjected
to the vehicle weight, such as when moving the ve-
hicle with the drive shaft removed.
Therefore, if it is absolutely necessary to place the ve-
hicle weight on the hub bearing, first support it with
the SST.
SST 09608–16042 (09608–02021, 09608–02041)
w/ ABS:
After disconnecting the drive shaft from the axle hub,
work carefully so as not to damage the ABS speed
sensor rotor serration on the drive shaft.
1. REMOVE FRONT WHEEL
2. DRAIN OUT GEAR OIL
3. w/ ABS:
REMOVE BOLT AND ABS SPEED SENSOR
4. REMOVE DRIVE SHAFT LOCK NUT
(a) Remove the cotter pin and lock cap.
(b) While applying the brakes, remove the nut.
5. DISCONNECT TIE ROD END FROM STEERING
KNUCKLE (See Pub. No. RM599E on page SA–11)
6. DISCONNECT LOWER BALL JOINT FROM LOWER
SUSPENSION ARM (See Pub. No. RM599E on page
SA–11)
7. DISCONNECT DRIVE SHAFT FROM AXLE HUB
(a) Using a plastic hammer, disconnect the drive shaft from
the axle hub.
NOTICE:
Cover the drive shaft boot and ABS speed sensor rotor with
cloth to protect it from being damaged.
(b) Push the front axle hub toward the outside of the vehicle
to separate the drive shaft from the axle hub.
8. REMOVE DRIVE SHAFTS
(a) RH drive shaft:
Remove the 2 bolts and pull out the drive shaft together
with the center bearing bracket.

SA02Z–03
SA–10
– SUSPENSION AND AXLEFRONT DRIVE SHAFT
INSTALLATION
1. LH drive shaft:
INSTALL DRIVE SHAFT TO TRANSAXLE
(a) Install a new snap ring to the inboard joint shaft.
(b) Coat the gear oil to the inboard joint shaft and differential case sliding surface.
(c) Set the snap ring with opening side facing downward.
(d) Using a brass bar and hammer, install the drive shaft.
NOTICE:
Be careful not to damage the dust cover of the drive shaft and oil seal lip of the transaxle.
HINT:
Whether the inboard joint shaft is in contact with the pinion shaft or not can be known from the sound or feel-
ing when driving it in.
(e) Check that there is 2 – 3 mm (0.08 – 0.12 in.) of play in the axial direction.
(f) Check that the drive shaft cannot be removed by hand.
2. RH drive shaft:
INSTALL DRIVE SHAFT TO TRANSAXLE
(a) Coat the gear oil to the inboard joint shaft and differential case sliding surface.
(b) Install the drive shaft with the center bearing bracket.
NOTICE:
Be careful not to damage the dust cover of the drive shaft and oil seal lip of the transaxle.
(c) Install the 2 bolts.
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
3. CONNECT DRIVE SHAFT TO AXLE HUB
NOTICE:
Be careful not to damage the boot and ABS speed sensor rotor.
4. CONNECT LOWER SUSPENSION ARM TO LOWER BALL JOINT
Torque: 127 N·m (1,300 kgf·cm, 94 ft·lbf)
5. CONNECT TIE ROD END TO STEERING KNUCKLE
(a) Connect the tie rod end to the steering knuckle.
(b) Install the nut and a new cotter pin.
If the holes for the cotter pin are not aligned, tighten the nut further up to 60.
Torque: 49 N·m (500 kgf·cm, 36 ft·lbf)
6. INSTALL DRIVE SHAFT LOCK NUT
(a) While applying brakes, install the nut.
Torque: 216 N·m (2,200 kgf·cm, 159 ft·lbf)
(b) Install the lock cap and a new cotter pin.
If the holes for the cotter pin are not aligned, tighten the nut further up to 60.
7. w/ABS:
INSTALL ABS SPEED SENSOR AND BOLT
Torque: 8.0 N·m (82 kgf·cm, 71 in.·lbf)
8. FILL AND CHECK GEAR OIL (See page MX–4)
9. INSTALL FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
10. CHECK FRONT WHEEL ALIGNMENT (See Pub. No. RM599E on page SA–4)
11. CHECK ABS SPEED SENSOR SIGNAL (See Pub. No. RM599E on page DI–115)

BR11O–01
F08965Non–reusable part N·m (kgf·cm, ft·lbf) : Specified torque
Vacuum Pump

Gasket Vacuum Hose
Casing
Rotor
BladeStraight
Pin
End Cover Check Valve
Union
O–Ring
Vacuum Hose

O–Ring

Gasket

Gasket

O–Ring
Oil Hose
Straight Pin
21 (214, 15)
74 (750, 54)
14 (140, 10)
7.8 (80, 68 in.·lbf)

Snap Ring
Coupling
BR–2
– BRAKEVACUUM PUMP (1CD–FTV)
VACUUM PUMP (1CD–FTV)
COMPONENTS