rear TOYOTA AVENSIS 1999 Supplement

Z14034
Fig.1
Fig.2Power Source
Safing
Sensor
Squibs
Deceleration Sensor
H01581
Outer
H01582
Lock of connector is released
Disconnection is completed
RS–6
– SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
(b) When the vehicle is involved in a frontal collision in the
hatched area (Fig. 1) and the shock is larger than the pre-
determined level, the SRS is activated automatically. A
safing sensor is designed to go on at a smaller decelera-
tion rate than the airbag sensor. As illustrated in Fig. 2,
ignition is caused when current flows to the squib, which
happens when a safing sensor and the deceleration sen-
sor go on simultaneously. When a deceleration force acts
on the sensors, 2 squibs in the driver airbag and front pas-
senger airbag ignite and generate gas. The gas discharg-
ing into the driver airbag and front passenger airbag rap-
idly increases the pressure inside the bags, breaking
open the steering wheel pad and instrument panel door.
Bag inflation then ends, and the bags deflate as the gas
is discharged through discharge holes at the bag’s rear or
side.
7. DISCONNECTION OF SIDE AND CURTAIN SHIELD
AIRBAG SENSOR CONNECTOR
(a) With holding both flank sides of the outer, slide the outer
to the direction shown by an arrow.
(b) Lock of the connectors is released, then disconnect the
connectors.
HINT:
Make sure to hold both flank sides of the outer. If holding the top
and bottom sides, it will obstruct disconnection.

H01583
Outer
Outer
– SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
RS–7
8. CONNECTION OF SIDE AND CURTAIN SHIELD AIR-
BAG SENSOR CONNECTOR
(a) Align the male connector (of the side of sensor) and fe-
male connector in the same direction as shown in the il-
lustration and fit in them without rubbing.
(b) As they are fitted in, the outer slides rearward. Press it un-
til the outer returns to its original position again.
If fitting stops half way, connectors will separate.
(c) Make sure to insert until they are locked. After fitting in,
pull them slightly to check that they are locked. (When
locked, make sure that the outer returns to its original
position and sound at the time of fitting in can be heard.)
HINT:

Do not fit in while holding the outer.

When fitting in, the outer slides. Do not touch it.

RS0IQ–01
H03410
H03411
H03408
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
RS–19
INSTALLATION
NOTICE:
Never use airbag parts from another vehicle. When replac-
ing parts, replace them with new parts.
1. INSTALL THESE PARTS TO SEATBACK FRAME
(a) Install the seatback pad.
(b) Install the hog rings and seatback cover.
(c) Hang the hook of the seatback cover.
2. INSTALL SEATBACK TO SEAT CUSHION ASSEMBLY
Using a torx wrench, install the 4 screws and seatback assem-
bly.
Torx wrench: T40 (Part No.09042–00020 or locally
manufactured tool)
Torque: 25 N·m (255 kgf·cm, 18 ft·lbf)
3. INSTALL THESE PARTS TO FRONT SEAT ASSEMBLY
(a) Install the 2 headrest supports.
(b) Install the headrest.
(c) Install the lumber support adjusting knob.
(d) Install the front seat inner shield.
4. INSTALL FRONT SEAT
(a) Mount the seat to the vehicle.
(b) Connect the side airbag connector.
(c) Install the outer bolt and inner bolt on the front side after
sliding the seat to the rearmost position.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(d) Tighten the bolts on the rear side temporarily, tighten
them completely starting from the bolt on the inner side.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(e) Install the front seat belt lap outer anchor.
Torque: 42 N·m (430 kgf·cm, 31 ft·lbf)
(f) Install the front seat cushion outer shield and reclining ad-
juster knob.
(g) Install the 2 seat track covers.

RS0IR–01
H11612
Roof Headlining
Front Pillar GarnishCenter Pillar Upper Garnish
Center Pillar Lower Garnish Front Seat Outer Belt Assist Grip
Front Door Operating Trim
Front Door Scuff Plate
Rear Door Scuff Plate Rear Door Operating Trim
Map Light Sun Visor
Pillar Garnish Cover
H11611
Sedan Model Liftback Model Wagon Model
Roof Side
Inner Garnish
Side Seatback
Rear Seat CushionDeck Trim
Side Board
Rear Floor
Carpet Deck Side Trim
Cover and Panel
Tonneau
Cover
Rear Floor
Finish Plate Rear Seat
Outer Belt
Roof Side
Inner Garnish
Side Seatback
Roof Side
Inner Garnish
Rear Seatback
Assembly
Rear Side
Seatback
Room
Partition
Net
N·m (kgf·cm, ft·lbf): Specified torque
42 (430, 31)
21 (214, 15)
21 (214, 15)
21 (214, 15)
RS–20
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
CURTAIN SHIELD AIRBAG ASSEMBLY
COMPONENTS

H11621
Instrument Panel
Column CoverNo.1 Register
Steering Wheel Combination Meter
Steering Wheel PadHeater Control Assembly
Cluster Finish Panel
Glove Compartment DoorFront Ash Receptacle
Lower Finish Panel
Rear Console Box No.1 Under Cover
Shift Knob
Parking Brake Hole Cover Combination Switch
Center Cluster Finish Panel
78 (790, 58)
N·m (kgf·cm, ft·lbf) : Specified torque
Cowl Side Panel
18 (184, 13)
Cover
Cover
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS–21

H11615
(1)(2)
(3)
(4)(5)(6)
H11622
Clear Plastic Bag
RS–24
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
4. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY
(a) Remove the instrument panel assembly. (See page
BO–16)
(b) Disconnect the curtain shield airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(c) In the order shown in the illustration, remove the bolts and
grommets, then remove the curtain shield airbag assem-
bly.
HINT:
In case of removing (5) and (6), bind the front and rear of the
airbag, and remove.
(d) Put the removed curtain shield airbag in a clear plastic
bag and keep it in a safe place.
NOTICE:
Protection bag is not reuse.
CAUTION:
Never disassemble the curtain shield airbag assembly.

RS0IX–01
H03424: Specified torqueN·m (kgf·cm, ft·lbf)Side and Curtain Shield Airbag Sensor Assembly
21 (210, 15)
Front Seat Outer Belt Retractor
5.0 (51, 44 in.·lbf)
42 (430, 31)
Center Piller Garnish
Rear Door Scuff Plate
Front Door Scuff Plate
RS–34– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLY
SIDE AND CURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
COMPONENTS

RS0IY–01
H03674
H03425
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLYRS–35
REMOVAL
NOTICE:
Do not open the cover or the case of the ECU and various
electrical devices unless absolutely necessary.
(If the IC terminals are touched, the IC may be destroyed by
static electricity.)
1. REMOVE FRONT AND REAR SCUFF PLATE
2. REMOVE CENTER PILLAR LOWER GARNISH
3. REMOVE FRONT SEAT OUTER BELT RETRACTOR
(See Pub. No. RM599E on page BO–151)
(a) Disconnect the pretensioner connector.
(b) Remove the 2 bolts and retractor.
4. REMOVE SIDE AND CURTAIN SHIELD AIRBAG SEN-
SOR ASSEMBLY
(a) Disconnect the connector.
NOTICE:
Remove the connector with the sensor assembly installed.
(b) Remove the 2 bolts, nut and side and curtain shield airbag
sensor assembly.

RS0J1–01
H03425
H03674
RS–38– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLY
INSTALLATION
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.

Never reuse the side and curtain shield airbag sensor
assembly involved in a collision when the airbag has
deployed.

Never repair a sensor in order to reuse it.
1. INSTALL SIDE AND CURTAIN SHILD AIRBAG SEN-
SOR
(a) Install the side and curtain shield airbag assembly with
the 2 bolts and nut.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
(b) Connect the side and curtain shild airbag sensor connec-
tor.
NOTICE:

Installation of the connector is done with the sensor
assembly installed. Make sure the sensor assembly
is installed with the specified torque.

If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.

When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.

After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL FRONT SEAT OUTER BELT RETRACTOR
(See pub. No. RM599E on page BO–159)
(a) Install the retractor with the 2 bolts.
Torque:
Upper bolt: 5.0 N·m (51 kgf·cm, 44 in.·lbf)
Lower bolt: 42 N·m (430 kgf·cm, 31 ft·lbf)
(b) Connect the pretensioner connecter.
3. INSTALL CENTER PILLAR LOWER GARNISH
4. INSTALL FRONT AND REAR DOOR SCUFF PLATE

I12428
ON
OFF
10 11
16
BE196–02
I12429
ON
OFF
10
16
– BODY ELECTRICALFOG LIGHT SYSTEM
BE–1
FOG LIGHT SYSTEM
INSPECTION
1. INSPECT FRONT/REAR FOG LIGHT SWITCH CONTI-
NUITY
Switch positionTester connectionSpecified condition
OFF–No continuity
ON (FRONT)11 – 16Continuity
ON (FRONT/REAR)10 – 11 – 16Continuity
If continuity is not as specified, replace the switch.
2. INSPECT REAR FOG LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF–No continuity
ON10 – 16Continuity
If continuity is not as specified, replace the switch.