instrument cluster TOYOTA AVENSIS 1999 Supplement

H11621
Instrument Panel
Column CoverNo.1 Register
Steering Wheel Combination Meter
Steering Wheel PadHeater Control Assembly
Cluster Finish Panel
Glove Compartment DoorFront Ash Receptacle
Lower Finish Panel
Rear Console Box No.1 Under Cover
Shift Knob
Parking Brake Hole Cover Combination Switch
Center Cluster Finish Panel
78 (790, 58)
N·m (kgf·cm, ft·lbf) : Specified torque
Cowl Side Panel
18 (184, 13)
Cover
Cover
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS–21

BO19J–02
I12662
Reinforcement
No.1 BraceFront Pillar Garnish
Instrument Panel
Front Door Opening Trim
Rear Door
Scuff Plate
Glove Compartment Door Heater Control
Assembly
No.1 Under Cover
Rear Console Box
Parking Brake Hole Cover Steering Wheel Pad Steering Wheel Combination Switch Column CoverLower Finish Panel Cluster Finish Panel Combination Meter No.1 Register
Center Cluster
Finish Panel
Front Door Scuff Plate Cowl Side Trim
Center Pillar Lower GarnishRear Door Opening Trim
B C
D
F G
A
A
B
CC
D
E
E
E
EE
E
E
EE
F
G
G
G
HHH
x 4Front Ash Receptacle
34 (350, 25)
18 (185, 13)
: Specified torqueN·m (kgf·cm, ft·lbf)
Curtain Shield Airbag
F
F
w/ Curtain shield air bag:
Front Pillar Garnish
– BODYINSTRUMENT PANEL
BO–13
INSTRUMENT PANEL
COMPONENTS

BO2J3–01
I12491
H03659
H03660
: 4 Clips BO–16
– BODYINSTRUMENT PANEL
REMOVAL
1. REMOVE THESE PARTS:
(a) Remove the front door opening trims.
(b) Remove the front pillar garnishes.
(c) w/ Curtain Shield Airbag:
(1) Remove the 2 bolts.
(2) Pack the airbag with protection cover.
(3) Using a screwdriver, raise the pillar garnish cover.
(4) Remove the bolt, pillar garnish cover and front pillar
garnish.
NOTICE:
Protection rang is from instrument panel to ceiling.
(d) Remove the front door scuff plates.
(e) Remove the cowl side trims.
(f) Remove the rear door opening trims.
(g) Remove the rear door scuff plates.
(h) Remove the center pillar lower covers.
(i) Remove the front seats.
2. REMOVE STEERING WHEEL
(See Pub. No.RM599E on page SR–13)
3. REMOVE LOWER FINISH PANEL
(a) Remove the 2 screws and hood lock control lever.
(b) Remove the 2 screws and lower finish panel.
4. REMOVE THESE PARTS:
(See Pub. No.RM599E on page SR–13)
(a) Remove the column cover.
(b) Remove the combination switch.
(c) Remove the steering column.
5. REMOVE CLUSTER FINISH PANEL
(a) Remove the 2 screws.
(b) Using a screwdriver, remove the cluster finish panel, then
disconnect the connector.
HINT:
Tape the screwdriver tip before use.
6. REMOVE COMBINATION METER

H03661
: 4 Clips
H03662
: 3 Clips
H03663
H03664
H03665
: 6 Clips
– BODYINSTRUMENT PANEL
BO–17
7. REMOVE NO.1 REGISTER
Using a screwdriver, remove the No.1 register.
HINT:
Tape the screwdriver tip before use.
8. REMOVE NO.1 UNDER COVER
Using a screwdriver, remove the No.1 under cover.
HINT:
Tape the screwdriver tip before use.
9. REMOVE GLOVE COMPARTMENT DOOR
Remove the 2 glove shaft and glove compartment door.
10. REMOVE PARKING BRAKE HOLE COVER
11. REMOVE REAR CONSOLE BOX
(a) M/T:
Remove the shift lever knob.
(b) Remove the 2 bolts, 4 caps, 4 screws and rear console
box.
12. REMOVE CENTER CLUSTER FINISH PANEL
Using a screwdriver, remove the panel, then disconnect the
connectors.
13. REMOVE HEATER CONTROL ASSEMBLY
(See Pub. No.RM599E on page AC–106)

BO2J4–01
H03666
H03665
H03664
H03663
– BODYINSTRUMENT PANEL
BO–19
INSTALLATION
1. INSTALL THESE PARTS:
(a) Install the reinforcement.
(b) Install the No.1 brace.
2. INSTALL INSTRUMENT PANEL
(a) Install the 6 screws and 3 nuts.
(b) Install the passenger airbag assembly with the 2 bolts.
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
3. INSTALL HEATER CONTROL ASSEMBLY
(See Pub. No.RM599E on page AC–111)
4. INSTALL CENTER CLUSTER FINISH PANEL
Install the panel, then connect the connectors.
5. INSTALL REAR CONSOLE BOX
(a) Install the console box with the 2 bolts and 4 caps, 4
screws.
(b) M/T:
Install the shift lever knob.
6. INSTALL PARKING BRAKE HOLE COVER
7. INSTALL GLOVE COMPARTMENT DOOR
Install the glove compartment door with the 2 glove shaft.

H03662
: 3 Clips
H03661
: 3 Clips
H03660
: 3 Clips
H03659
BO–20
– BODYINSTRUMENT PANEL
8. INSTALL NO.1 UNDER COVER
Install the No.1 under cover.
9. INSTALL NO.1 REGISTER
Install the No.1 register.
10. INSTALL COMBINATION METER
11. INSTALL CLUSTER FINISH PANEL
(a) Install the cluster finish panel, then connect the connec-
tor.
(b) Install the 2 screws.
12. INSTALL THESE PARTS:
(See Pub. No. RM 599E, page SR–13)
(a) Install the steering column.
(b) Install the combination switch.
(c) Install the column cover.
13. INSTALL LOWER FINISH PANEL
(a) Install the lower finish panel with the 2 screws.
(b) Install the hood lock control lever.
14. INSTALL STEERING WHEEL
(See Pub. No. RM 599E, page SR–13)
15. INSTALL THESE PARTS:
(a) Install the front seats.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(b) Install the center pillar lower covers.
(c) Install the rear door scuff plates.
(d) Install the rear door opening trims.
(e) Install the cowl side trims.
(f) Install the front door scuff plates.