alternator TOYOTA AVENSIS 2003 Service User Guide

010BA±14
01±42
±
INTRODUCTION TERMS
AVENSIS REPAIR MANUAL (RM1018E)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE±J1930 terms and abbreviations used in this ma\
nual in compliance with SAE rec-
ommendations, as well as their TOYOTA equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOTA TERMS
( )±±ABBREVIATIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner, A/CL
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal±
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric PressureHAC
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection±
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position±
CTOXContinuous Trap Oxidizer±
CTPClosed Throttle PositionLL ON, Idle ON
DFIDirect Fuel Injection (Diesel)Direct Injection (DI/INJ)
DIDistributor Ignition±
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Communication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Trouble Code
DTMDiagnostic Test Mode±
ECLEngine Control Level±
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant TemperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionDistributorless Ignition (DLI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control±
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory±
FEPROMFlash Erasable Programmable Read Only Memory±
FFFlexible Fuel±
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)
http://vnx.su

031E7±03
±
SERVICE SPECIFICATIONS STARTING & CHARGING
03±33
AVENSIS REPAIR MANUAL (RM1018E)
TORQUE SPECIFICATION
1ZZ±FE/3ZZ±FE:
Part TightenedN
mkgf
cmft
lbf
Starter assy x Transaxle housing3737828
Starter wire x Starter assy9.81007
Generator assy x Transverse engine engine mounting bracket2525518
Generator assy x Cylinder block sub±assy5455140
Generator wire x Generator assy9.81007
Lead wire of field coil x Terminal C5.96052 in.
lbf
1AZ±FE/1AZ±FSE:
Part TightenedN
mkgf
cmft
lbf
Wire harness clamp bracket x Starter assy8.48674 in.
lbf
Starter assy x Cylinder block sub±assy3738028
Starter wire x Starter assy9.81007
Battery carrier x Body131319
Battery clamp sub±assy x Body5.05144 in.
lbf
Battery clamp sub±assy x Battery clamp bolt3.63631 in.
lbf
Terminal x Battery5.45548 in.
lbf
Wire harness clamp bracket x Generator assy8.48674 in.
lbf
Generator assy x Cylinder block sub±assy Bolt A
Bolt B52
21530
21438
16
Generator wire x Generator assy9.81007
Lead wire of field coil x Terminal C5.96052 in.
lbf
1CD±FTV:
Part TightenedN
mkgf
cmft
lbf
Starter x Transaxle Bolt
Terminal 3037
9.8377
10027
7.2
Generator assy x Engine M8
M10
Alternator wire Wire harness31
47
9.8
5.0320
475
100
5123
347
44 in.
lbf
Glow plug assy x Cylinder head Glow plug
Nut12.32.2125229
19 in.
lbf
Engine cover No. 1 x Cylinder head cover sub±assy8.08271 in.
lbf
Engine cover No. 1 x Intake manifold8.08271 in.
lbf
Front wheel RH1031,05076
http://vnx.su

140DD±03
A57063
Measure Point for Belt
Deflection and Tension
Alternator
Crankshaft Compressor
P/S P/S
Alternator Crankshaft
A/C equipped
A/C not equipped
A61173
B
A
14±266
±
ENGINE MECHANICALENGINE(1CD±FTV)
AVENSIS REPAIR MANUAL (RM1018E)
ENGINE(1CD±FTV)
INSPECTION
1.INSPECT COOLANT (See page 16±37)
2.INSPECT ENGINE OIL (See page 17±20)
3.INSPECT BATTERY (See page 19±26)
4. INSPECT AIR CLEANER FILTER ELEMENT SUB±ASSY 5. INSPECT DRIVE BELT
(a) Inspect vane pump V belt.(1) Measure the belt deflection
Pressing force: 98 N
m (10 kgf 22 lbf)
New belt
mm (in.)Used belt mm (in.)
A/C equipped9.5 to 11.5
(0.37 to 0.45)12.5 to 15.5
(0.49 to 0.61)
A/C not equipped10 to 12
(0.39 to 0.47)14 to 17
(0.55 to 0.67)
(2) Measure the belt tension
New belt
N (kgf, lbf)Used belt
N (kgf, lbf)
A/C equipped519 to 755
(53 to 77, 117 to 170)196 to 392
(20 to 40, 44 to 88)
A/C not equipped686 to 784
(70 to 80, 154 to 176)294 to 441
(30 to 45, 66 to 99)
NOTICE:

Check the drive belt deflection at the specified point.

When installing a new belt, set its tension value as
specified.

When inspecting the belt which is used over 5 min-
utes, apply the specifications of ºUsed Belt.º

When reinstalling the belt which is used over 5 min-
utes, adjust its deflection and tension to the medium
value in each specification of ºUsed Belt.º

V±ribbed belt tension and deflection should be
checked after 2 revolutions of engine cranking.

When using a belt tension gauge, confirm the accura-
cy by using a master gauge first.
(b) Inspect generator V belt. (1) Check that the tension indicator is within range A onthe auto tensioner scale.
If the tension is not within the A range, replace the belt with a
new one.
HINT:
When replacing the drive belt with a new one, the belt tension
should be within the B range.
http://vnx.su

010BJ±01
±
INTRODUCTION TERMS (1ZZ±FE/3ZZ±FE)
01±7
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
TERMS (1ZZ±FE/3ZZ±FE)
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti±Lock Brake System
A/CAir Conditioner
ACAlternating Current
ACCAccessory
ACISAcoustic Control Induction System
ACSDAutomatic Cold Start Device
A.D.D.Automatic Disconnecting Differential
A/FAir±Fuel Ratio
AHCActive Height Control Suspension
ALRAutomatic Locking Retractor
ALTAlternator
AMPAmplifier
ANTAntenna
APPROX.Approximately
ASSYAssembly
A/TAutomatic Transmission (Transaxle)
AT FAutomatic Transmission Fluid
AUTOAutomatic
AUXAuxiliary
AV GAverage
AV SAdaptive Variable Suspension
B+Battery Voltage
BACSBoost Altitude Compensation System
BATBattery
BDCBottom Dead Center
B/LBi±Level
B/SBore±Stroke Ratio
BTDCBefore Top Dead Center
BVSVBimetallic Vacuum Switching Valve
CBCircuit Breaker
CCoCatalytic Converter For Oxidation
CDCompact Disc
CFCornering Force
CGCenter Of Gravity
CHChannel
CKDComplete Knock Down
COMB.Combination
CPECoupe
CPSCombustion Pressure Sensor
CPUCentral Processing Unit
CRSChild Restraint System
CTRCenter
C/VCheck Valve
CVControl Valve
CWCurb Weight
DCDirect Current
DEFDefogger
DFLDeflector
http://vnx.su

010BK±01
01±12
±
INTRODUCTION TERMS (1ZZ±FE/3ZZ±FE)
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE±J1930 terms and abbreviations used in this ma\
nual in compliance with SAE rec-
ommendations, as well as their TOYOTA equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOTA TERMS
( )±±ABBREVIATIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner, A/CL
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal±
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric PressureHAC
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection±
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position±
CTOXContinuous Trap Oxidizer±
CTPClosed Throttle PositionLL ON, Idle ON
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition±
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Comunication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode±
ECLEngine Control Level±
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant TemperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionTOYOTA Distributorless Ignition (TDI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control±
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory±
FEPROMFlash Erasable Programmable Read Only Memory±
FFFlexible Fuel±
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)
http://vnx.su

02148±01
±
PREPARATION STARTING & CHARGING
02±5
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
STARTING & CHARGING
PREPARATION
SST
09286±46011Injection Pump Spline Shaft
PullerGENERATOR ASSY
(1ZZ±FE/3ZZ±FE)
09820±63010Alternator Pulley Set Nut Wrench
SetGENERATOR ASSY
(1ZZ±FE/3ZZ±FE)
(09820±06010)Alternator Rotor Shaft WrenchGENERATOR ASSY
(1ZZ±FE/3ZZ±FE)
(09820±06020)Alternator Pulley Set Nut 22 mm
WrenchGENERATOR ASSY
(1ZZ±FE/3ZZ±FE)
Recomended Tools
09011±12291Socket Wrench for 29 mm .GENERATOR ASSY
(1ZZ±FE/3ZZ±FE)
09082±00040TOYOTA Electrical TesterSTARTER ASSY
(1ZZ±FE/3ZZ±FE)
GENERATOR ASSY
(1ZZ±FE/3ZZ±FE)
(09083±00150)Test Lead SetSTARTER ASSY
(1ZZ±FE/3ZZ±FE)
GENERATOR ASSY
(1ZZ±FE/3ZZ±FE)
Equipment
Ohmmeter
Sandpaper
V±block
Dial indicator
Vernier calipers
Plastic hammer
Torque wrench
Wooden block
http://vnx.su

190AA±01
A62753
SST
1 ± BSST
1 ± A
A62754SST 2
A62755
SST
1 ± A
A62756
SST
1 ± A
SST
1 ± B
19±10
±
STARTING & CHARGING GENERATOR ASSY (1ZZ±FE/3ZZ±FE)
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
OVERHAUL
1. REMOVE GENERATOR PULLEY SST 09820±63010 (09820±06010, 09820±06020)
HINT:
SST1 ± A, B09820±06010
SST209820±06020
(a) Hold SST 1 ± A with a torque wrench, and tighten SST 1 ± B clockwise to the specified torque.
Torque: 39 N
m (398 kgf
cm, 29 ft
lbf)
NOTICE:
Check that SST is secured to the rotor shaft.
(b) Mount SST 2 in a vise.
(c) Insert SST 1 ± A, B into SST 2, and attach the pulley nut to SST 2.
(d) To loosen the pulley nut, turn SST 1 ± A in the direction shown in the illustration.
NOTICE:
To prevent damage to the rotor shaft, do not loosen the
pulley nut more than one±half of a turn.
(e) Remove the alternator form SST 2.
(f) Turn SST 1 ± B, and remove SST 1 ± A, B.
(g) Remove the pulley nut and pulley.
http://vnx.su

A62753
SST
1 ± BSST
1 ± A
A62754SST 2
A62765
SST
1 ± A
19±14
±
STARTING & CHARGING GENERATOR ASSY (1ZZ±FE/3ZZ±FE)
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
(b) Install the rear end cover with the 2 nuts. Torque: 4.4 N
m (45 kgf
cm, 39 in.
lbf)
(c) Install the terminal plate with the screw and nut.
Torque:
Bolt 3.9 N
m (40 kgf
cm, 35 in.
lbf)
Nut 4.4 N
m (45 kgf
cm, 39 in.
lbf)
(d) Install the terminal insulator withe the nut.
Torque: 4.1 N
m (42 kgf
cm, 36 in.
lbf)
14. INSTALL GENERATOR PULLEY SST 09820±63010 (09820±06010, 09820±06020)
HINT:
SST1 ± A, B09820±06010
SST209820±06020
(a) Install the pulley to the rotor shaft by tightening the pulley nut by hand.
(b) Hold SST 1 ± A with a torque wrench, and tighten SST 1 ± B clockwise to the specified torque.
Torque: 39 N
m (398 kgf
cm, 29 ft
lbf)
NOTICE:
Check that SST is secured to the pulley shaft.
(c) Mount SST 2 in a vise.
(d) Insert SST 1 ± A, B into SST 2, and attach the pulley nut to SST 2.
(e) Tighten the pulley nut, turn SST 1 ± A in the direction shown in the illustration.
Torque: 111 N
m (1,132 kgf
cm, 82 ft
lbf)
(f) Remove the alternator form SST 2.
http://vnx.su

I35431
Burner Motor
Glow Plug
Surface Sensor
Temp. Control Sensor
Flame Sensor 13
Power
Heater
ECU
Connector B Terminal L
of Alternator
Battery
Metering Pump
Fuse (20 A)
Vehicle Side
SW
14
9
12
5
6
3
4
1
2 R
BR
B±R
G
L±Y L
Y
L±W 5
1
6
2
7
3
8
4
W±B
R±G
R±B
Connector A
IG
W±R (*1)
Y±R (*2)R±L (*1)
R±Y (*2)
*1: TMC Made
*2: TMUK Made
55±16
±
HEATER & AIR CONDITIONER COMBUSTION TYPE POWER HEATER SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
2. DESCRIPTION OF DISPLAY AND BUTTONS
(a) AF: Current Value Malfunction (Blinking at current failure) Diag: DTC (Example: 064 Flame sensor break)
Memory Clear button: Deletion of faulty memory (Press both buttons together for longer than 2 se-
conds)
> Button: Scroll up of faulty memory (The past 5 codes can be stored.)\
< Button: Scroll down of faulty memory (The past 5 codes can be stored.\
)
3. FAULTY MEMORY
(a) The ECU is able to store up to 5 pieces of faulty memory. If it is full, the new data is written over F5.
4. WIRING DIAGRAM
http://vnx.su

38AVENSIS (EWD526E)
G ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
[LHD : 1AZ–FSE]
A5
F6
C6
A10
H2
H6
F11
F9
(*1)
(*2) *1:w/ HID
*2:w/o HID
F10
F2
E4
A6
A4
E5
F5
B1
H1
H5
E2
F7
F8
H9C2H10F16H7C1H8B3B2F13F12
H12A12A3C3A11H3F4H4H11A1A2E1A9F3F1
C5
(A/T)
(*1)
(*2)
(M/T)
A 1 A/C Ambient Temp. Sensor
A 2 A/C Condenser Fan Motor
A 3 A/C Pressure Sensor
A 4 ABS Speed Sensor Front LH
A 5 ABS Speed Sensor Front RH
A 6 Air Flow Meter
A 9 Airbag Sensor Front LH
A 10 Airbag Sensor Front RH
A 11 Alternator
A 12 Alternator
B 1 Back–Up Light SW
B 2 Brake Booster Pressure Sensor
B 3 Brake Fluid Level Warning SW
C 1 Camshaft Position Sensor
C 2 Camshaft Timing Oil Control Valve
C 3 Compressor Assembly
C 5 Counter Gear Speed Sensor
C 6 Crankshaft Position Sensor
E 1 ECT Solenoid
E 2 EFI Water Temp. Sensor
E 4 Electronic Driver Unit
E 5 Electronic Driver Unit
F 1 Front Clearance Light LH
F 2 Front Clearance Light RH
F 3 Front Fog Light LH F 4 Front Fog Light RH
F 5 Front Side Turn Signal Light LH
F 6 Front Side Turn Signal Light RH
F 7 Front Turn Signal Light LH
Headlight Control ECU LH
F 8 Front Turn Signal Light LH Headlight LH (Low)
F 9 Front Turn Signal Light RH Headlight Control ECU RH
F 10 Front Turn Signal Light RH Headlight RH (Low)
F 11 Front Washer Motor
F 12 Front Window Deicer
F 13 Front Wiper Motor
F 16 Fuel Pressure Sensor
H 1 Headlight Beam Level Control Actuator LH
H 2 Headlight Beam Level Control Actuator RH
H 3 Headlight Cleaner Control Relay
H 4 Headlight Cleaner Motor
H 5 Headlight LH (High)
H 6 Headlight RH (High)
H 7 Heated Oxygen Sensor (Bank 1 Sensor 1)
H 8 Heated Oxygen Sensor (Bank 1 Sensor 2)
H 9 Heated Oxygen Sensor (Bank 2 Sensor 1)
H 10 Heated Oxygen Sensor (Bank 2 Sensor 2)
H 11 Horn LH
H 12 Horn RH
http://vnx.su