stop start TOYOTA C-HR 2016 User Guide

1112. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
*1: These lights turn on when the engine switch is turned to the “ON” position
(vehicles without a smart entry & start system) or IGNITION ON mode
(vehicles with a smart entry & start system) to indicate that a system check
is being performed. They will turn off after the engine is started, or after a
few seconds. There may be a malfunction in a system if a light does not
come on, or if the lights do not turn off. Have the vehicle inspected by any
authorized Toyota retailer or Toyota authorized repairer, or any reliable
repairer.
*2: The light comes on to indicate a malfunction.
*3: The light flashes to indicate a malfunction.
*4: Vehicles with monochrome display
*4LDA indicator (yellow) (if equipped) P. 696
*3Stop & Start cancel indicator (if equipped) P. 697
*3Parking brake indicator P. 697
Low fuel level warning light P. 697
Driver’s and front passenger’s seat belt
reminder light P. 6 9 7
Rear passengers’ seat belt reminder lights (on
the center panel) P. 6 9 7
*1Tire pressure warning light P. 698
*1Master warning light P. 698
Warning lightsPages

1132. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
*2LDA indicator (green) (if equipped) P. 315
*1“BSM” indicator (if equipped) P. 392
*4BSM outside rear view mirror indicator
(on the outside rear view mirrors) (if equipped) P. 3 9 2
“RCTA” indicator (if equipped) P. 392
Security indicator (on the center panel) P. 87,
97
*1, 3Auto P-off indicator P. 257
*1, 2Brake hold operated indicator P. 262
*1, 5Slip indicator light P. 463
*1VSC off indicator P. 464
*1, 6PCS warning light (if equipped) P. 302
*1“PASSENGER AIR BAG” indicator (on the
center panel) (if equipped) P. 5 7
Stop & Start cancel indicator (if equipped) P. 375
IndicatorsPages

1162. Instrument cluster
C-HR_OM_Europe_OM10528E
*1: These lights turn on when the engine switch is turned to the “ON” position
(vehicles without a smart entry & start system) or IGNITION ON mode
(vehicles with a smart entry & start system) to indicate that a system check
is being performed. They will turn off after the engine is started, or after a
few seconds. There may be a malfunction in a system if a light does not
come on, or if the lights do not turn off. Have the vehicle inspected by any
authorized retailer or Toyota authorized repairer, or any reliable repairer.
*2: Vehicles with color display only
*3: Vehicles with a Multidrive
*4: Vehicles with a manual transmission
*2Stop & Start indicator (if equipped) P. 374
*2Speed limit sign (if equipped) P. 330
Low outside temperature indicator P. 120
IndicatorsPages

1182. Instrument cluster
C-HR_OM_Europe_OM10528E
■Eco Driving Indicator Light (vehicles with a Multidrive)
Eco Driving Indicator Light will not operate in the following conditions:
● The shift lever is in anything other than D.
● The vehicle is being driven in “SPORT” mode (P. 385)
● The vehicle speed is approximately 130 km/h (80 mph) or higher.
During Eco-Friendly acceleration (Eco
driving), Eco Driving Indicator Light will
turn on. When the acceleration exceeds
Zone of Eco driving, and when the vehicle
is stopped, the light turns off.
Eco Driving Indicator Light availability can
be customized. The default setting is on.
( P. 779)
WARNING
■If a safety system warning light does not come on
Should a safety system light such as ABS and SRS airbag warning light not
come on when you start the engine, this could mean that these systems are
not available to help protect you in an accident, which could result in death
or serious injury. Have the vehicle inspected any authorized Toyota retailer
or Toyota authorized repairer, or any reliable repairer.

1212. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
Odometer and trip meter display
Displays the following items.
Odometer:
Displays the total distance the vehicle has been driven.
Trip meter:
Displays the distance the vehicle has been driven since the meter was last
reset. Trip meters A and B can be used to record and display different dis-
tances independently.
Maintenance required information:
Displays the remaining distance until the engine oil should be changed. If
“-” is displayed before distance, it means oil maintenance is overdue. Have
the engine oil changed by any authorized Toyota retailer or Toyota autho-
rized repairer, or any reliable repairer.
• Displays the maintenance required information when the engine switch
is turned to the “ON” position (vehicles without smart entry & start sys-
tem) or in IGNITION ON mode (vehicles with smart entry & start sys-
tem).
• Maintenance required information reset method ( P. 621)
Stop & Start system operation time (if equipped):
Displays the total amount of time that the engine has been stopped due to
operation of the Stop & Start system during the time of the current engine
stop.
Instrument cluster light control display (monochrome display):
Displays the meter light control display.
Shift position and shift range display (color display)
Displays the selected shift position or selected shift range. ( P. 244)
Engine coolant temperature gauge
Displays the engine coolant temperature.
6
7
8

1232. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
■The meters and display illuminate when
Vehicles without a smart entry & start system:
The engine switch is in the “ON” position.
Vehicles with a smart entry & start system:
The engine switch is in IGNITION ON mode.
■ Outside temperature display
● In the following situations, the correct outside temperature may not be dis-
played, or the display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 25 km/h [16 mph])
• When the outside temperature has changed suddenly (at the entrance/
exit of a garage, tunnel, etc.)
● When “--” is displayed, the system may be malfunctioning.
Take your vehicle to any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
NOTICE
■ To prevent damage to the engine and its components
● Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
● The engine may be overheating if the engine coolant temperature gauge is
in the red zone (“H”). In this case, immediately stop the vehicle in a safe
place, and check the engine after it has cooled completely. ( P. 756)

1302. Instrument cluster
C-HR_OM_Europe_OM10528E
●Distance (driving range/after start)*1
Displays the estimated maximum distance that can be driven with the
quantity of fuel remaining and the distance driven after the engine was
started, respectively
• This distance is computed based on your average fuel consumption. As
a result, the actual distance that can be driven may differ from that dis-
played.
• When only a small amount of fuel is added to the tank, the display may
not be updated.
When refueling, turn the engine switch off. If the vehicle is refueled with-
out turning the engine switch off, the display may not be updated.
● Stop & Start system operation time (if equipped)*3
Displays the total amount of time that the engine has been stopped due to
operation of the Stop & Start system during the time of the current engine
stop.
● Eco Driving Indicator Zone Display
P. 134
●Speedometer
Displays the vehicle speed.
●Dynamic Torque Control AWD system display (AWD models)
P. 135

1332. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
●Vehicle Settings
Select the menu to set up the following items.
• RSA (Road Sign Assist) setup ( P. 335)*1
Select to set up RSA (Road Sign Assist).
• (Stop & Start system) setup (P. 379)*1
Select to set up Stop & Start system priority.
• (Tire pressure warning system) setup (P. 634)
Select to initialize the tire pressure warning system.
●Meter settings
Select the menu to set up the following items.
• Language
Select to change the language on the display.
•Units
Select to change the unit of measure for fuel consumption.
• (Eco Driving Indicator Light) setup*1
Select to activate/deactivate the Eco Driving Indicator Light
• Drive information 1 through 3
Select to select up to 2 items that will be displayed on a Drive informa-
tion screen, up to 3 Drive information screens can be set.
• Pop-up display
Select to set the pop-up displays*2, which may appear in some situa-
tions, on/off.
• Default settings
Registered or changed meter settings will be deleted or returned to their
default setting.
*1: If equipped
*2: Stop & Start system operation time display (if equipped), route guidance
display of the navigation system-linked system (if equipped) and incom-
ing call display of the hands-free phone system (if equipped).

1483-1. Key information
C-HR_OM_Europe_OM10528E
■ Key battery depletion
Vehicles without a smart entry & start system
If the wireless remote control function does not operate, the battery may be
depleted. Replace the battery when necessary. ( P. 652)
Vehicles with a smart entry & start system
● The standard battery life is 1 to 2 years.
● If the battery becomes low, an alarm will sound in the cabin when the engine
stops. ( P. 652)
● As the electronic key always receives radio waves, the battery will become
depleted even if the electronic key is not used. The following symptoms indi-
cate that the electronic key battery may be depleted. Replace the battery
when necessary. ( P. 652)
• The smart entry & start system or the wireless remote control does not
operate.
• The detection area becomes smaller.
• The LED indicator on the key surface does not turn on.
• The battery can be exchanged by the users. ( P. 652) However, as there
may be damage to the key when exchanging, it is recommended to have
the battery exchanged at any authorized Toyota retailer or Toyota autho-
rized repairer, or any reliable repairer.
● To avoid serious deterioration, do not leave the electronic key within 1 m
(3 ft.) of the following electrical appliances that produce a magnetic field:
•TVs
• Personal computers
• Cellular phones, cordless phones and battery chargers
• Recharging cellular phones or cordless phones
• Table lamps
• Induction cookers

1593-2. Opening, closing and locking the doors
3
Operation of each component
C-HR_OM_Europe_OM10528E
■ Door lock buzzer
Vehicles without a smart entry & start system
If an attempt to lock the doors using the wireless remote control is made
when a door is not fully closed, a buzzer will sound continuously for 10 sec-
onds. Fully close the door to stop the buzzer, and lock the doors again.
Vehicles with a smart entry & start system
If an attempt to lock the doors using the entry function or wireless remote
control is made when a door is not fully closed, a buzzer will sound continu-
ously for 5 seconds. Fully close the door to stop the buzzer, and lock the
doors again.
■ Setting the alarm (if equipped)
Lock the doors will set the alarm system. ( P. 97)
■ If the smart entry & start system or the wireless remote control does not
operate properly
Vehicles with a smart entry & start system: Use the mechanical key to lock
and unlock the doors. ( P. 747)
Replace the key battery with a new one if it is depleted. ( P. 652)