change time TOYOTA C-HR 2017 Owner's Manual

3714-5. Using the driving support systems
4
Driving
C-HR_OM_Europe_OM10528E
To change the set speed, operate the lever until the desired set speed
is obtained.
Increases the speed
Decreases the speed
Fine adjustment: Momentarily
move the lever in the desired
direction.
Large adjustment: Hold the lever
in the desired direction.
The set speed will be increased or decreased as follows:
Fine adjustment: By approximately 1 km/h (0.6 mph)*1 or 1 mph (1.6 km/h)*2
each time the lever is operated.
Large adjustment: The set speed can be increased or decreased continu-
ally until the lever is released.
*1: When the set speed is shown in “km/h”
*2: When the set speed is shown in “MPH”
Pulling the lever toward you
cancels the constant speed
control.
The speed setting is also canceled
when the brake pedal or clutch
pedal (manual transmission only)
is depressed.
Pushing the lever up resumes
the constant speed control.
However, resuming is available when the vehicle speed is more than
approximately 40 km/h (25 mph).
Adjusting the set speed
1
2
Canceling and resuming the constant speed control
1
2

3794-5. Using the driving support systems
4
Driving
C-HR_OM_Europe_OM10528E
■ Changing the idling stop time with the air conditioning system on
The length of time the Stop & Start system will operate when the air condition-
ing system is on can be changed by performing the following operation. (The
length of time the Stop & Start system will operate when the air conditioning
system is off cannot be changed.)
● Changing the setting by multi-information display
Use the meter control switches to select “ Setup” and press .
( P. 128)
● Changing the setting by the Stop & Start cancel switch
Each time the Stop & Start cancel switch is pressed and held for 3 seconds
or more, the system switches between standard and extended. The system
status can be confirmed on the settings display on the multi-information dis-
play. ( P. 128)
■ The Stop & Start system protection function
● When an excessively loud sound is being projected by the audio system,
the audio system may be automatically cut off in order to reduce battery
consumption. If it occurs, turn the engine switch off, wait for 3 seconds or
longer and then turn it to “ACC” or “ON” position to re-enable the audio sys-
tem.
● The audio system may not be activated when the battery terminals are dis-
connected and then reconnected. If it occurs, turn the engine switch off and
then repeat the following operation twice to activate the audio system nor-
mally.
• Turn the engine switch to “ON” position and then to OFF.
■ Replacing the battery
 P. 753
■ Displaying the Stop & Start system status
 P. 128
Select a desired setting and press
.
1
2

4164-5. Using the driving support systems
C-HR_OM_Europe_OM10528E
■ If “Parking Assist Malfunction” is displayed on the multi-information dis-
play
The system may not operate due to the malfunction of a sensor.
Have the vehicle inspected by any authorized Toyota retailer or Toyota autho-
rized repairer, or any reliable repairer.
■ Customization
Setting of buzzer volume can be changed.
(Customizable features: P. 776)
WARNING
■When using Toyota parking assist-sensor
Observe the following precautions to avoid an unexpected accident.
● Do not exceed the speed limit of 10 km/h (6 mph).
● The sensor detection areas and reaction times are limited. When moving
forward or reversing, check the areas surrounding the vehicle (especially
the sides of the vehicle) for safety, and drive slowly, using the brake to
control the vehicle’s speed.
● Do not install accessories within the sensors’ detection areas.

4264-5. Using the driving support systems
C-HR_OM_Europe_OM10528E
■Function summary
If a parking space can be detected, you will be guided forward until
you reach the assist control starting position, and then the parallel
parking assist mode can be used. Furthermore, depending on the
parking space and other conditions, multi-turn maneuvering assist
control is also provided if necessary.
Continue moving forward
with the vehicle parallel to
the curb or road. Then press
the S-IPA switch 1 time to
select the parallel parking
assist mode.
Travel straight ahead paral-
lel with the road or curb so
that the parking space is
detected.
A sound is issued and a dis-
play is shown to notify you
when the vehicle reaches a
position where assist control
can be used to begin backing
up from, and then when the
shift position is changed
according to guidance pro-
vided by the system, steering
wheel auto operation begins.
If the detected parking space or road width (distance to the side of the
road across from the parking space) is narrow, guidance will not be
issued.
Parking is complete
Move the vehicle forward and back repeatedly in accordance with the
guidance, until the vehicle is completely parked.
How to parallel park (parallel parking assist mode)
1
2
3
4

4274-5. Using the driving support systems
4
Driving
C-HR_OM_Europe_OM10528E
■Parking
Press the S-IPA switch 1 time
and check that the display on
the multi-information display
switches to parallel parking
assist mode.
Turn the S-IPA switch on while
driving the vehicle at 30 km/h
(18 mph) or less. The multi-
information display changes to
the parking space detection
screen when the system is oper-
ating.
Drive the vehicle while main-
taining a distance of approxi-
mately 1 m (3.3 ft.) from the
parked vehicles.
Proceed slowly.
The system will begin searching
for a parking space.
While searching for a space, the
turn signal lever ( P. 255) can
be operated to select a parking
space on the left or right.
When a parking space is
detected, the screen will
change.
1
Approx. 1 m
(3.3 ft.)
2

4354-5. Using the driving support systems
4
Driving
C-HR_OM_Europe_OM10528E
■Parking
Press the S-IPA switch
2 times and check that the
display on the multi-informa-
tion display switches to per-
pendicular parking assist
mode.
Turn the S-IPA switch on while
driving the vehicle at 20 km/h
(12 mph) or less.
The multi-information display changes to the parking space detection
screen when the system is operating.
Drive the vehicle while main-
taining a distance of approxi-
mately 1 m (3.3 ft.) from the
parked vehicles.
Proceed slowly.
The system will begin searching
for a parking space.
While searching for a space, the
turn signal lever ( P. 255) can
be operated to select a parking
space on the left or right.
When a parking space is
detected, the screen will
change.
1
Approx. 1m
(3.3 ft.)
2

5616-1. Using the air conditioning system and defogger
6
Interior features
C-HR_OM_Europe_OM10528E
■Fan speed setting
Increases the fan speed
Decreases the fan speed
Press to turn the fan off.
■Change the airflow mode
To change the airflow mode,
move the airflow change knob
upward or downward.
The air outlets used are
changed each time the knob is
operated.
Air flows to the upper body.
Air flows to the upper body
and feet.
Air flows to the feet.
Air flows to the feet and the
windshield defogger oper-
ates.
1
2
1
2
3
4

5676-1. Using the air conditioning system and defogger
6
Interior features
C-HR_OM_Europe_OM10528E
■Fan speed setting
Increases the fan speed
Decreases the fan speed
Press to turn the fan off.
■Change the airflow mode
To change the airflow mode,
move the airflow change knob
upward or downward.
The air outlets used are
changed each time the knob is
operated.
Air flows to the upper body.
Air flows to the upper body
and feet.
Air flows to the feet.
Air flows to the feet and the
windshield defogger oper-
ates.
1
2
1
2
3
4

5706-1. Using the air conditioning system and defogger
C-HR_OM_Europe_OM10528E
■Windshield wiper de-icer (if equipped)
This feature is used to prevent ice from building up on the wind-
shield and wiper blades.
Press .
The windshield wiper de-icer will automatically turn off after a period of
time.
■Blower customization
Fan speed settings can be changed.
Press .
Press .
Each time is pressed, the fan speed changes as follows.
“NORMAL” “ECO”“FAST”
1
2
3

5796-1. Using the air conditioning system and defogger
6
Interior features
C-HR_OM_Europe_OM10528E
Each time the switch is pressed,
the operation condition changes
as follows.
Hi (3 segments lit)  Mid (2 seg-
ments lit)  Lo (1 segment lit) 
Off
The level indicator (amber) light up
during operation.
■ Operating condition
Vehicles without a smart entry & start system
The seat heaters can be used when the engine switch is in the “ON” position.
Vehicles with a smart entry & start system
The seat heaters can be used when the engine switch is in IGNITION ON
mode.
Seat heaters