light TOYOTA C-HR 2017 Owner's Guide

1122. Instrument cluster
C-HR_OM_Europe_OM10528E
The indicators inform the driver of the operating state of the vehicle’s
various systems.
Indicators
IndicatorsPages
Turn signal indicator P. 255
Tail light indicator P. 265
Headlight high beam indicator P. 266
Front fog light indicator (if equipped) P. 276
Rear fog light indicator P. 276
Automatic High Beam indi cator (if equipped) P. 272
Parking brake indicator P. 256
*1, 2Brake hold standby indicator P. 262
Toyota parking assist-sensor indicator (if
equipped) P. 4 0 9
S-IPA indicator (if equipped) P. 422
*3“iMT” indicator P. 251

1132. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
*2LDA indicator (green) (if equipped) P. 315
*1“BSM” indicator (if equipped) P. 392
*4BSM outside rear view mirror indicator
(on the outside rear view mirrors) (if equipped) P. 3 9 2
“RCTA” indicator (if equipped) P. 392
Security indicator (on the center panel) P. 87,
97
*1, 3Auto P-off indicator P. 257
*1, 2Brake hold operated indicator P. 262
*1, 5Slip indicator light P. 463
*1VSC off indicator P. 464
*1, 6PCS warning light (if equipped) P. 302
*1“PASSENGER AIR BAG” indicator (on the
center panel) (if equipped) P. 5 7
Stop & Start cancel indicator (if equipped) P. 375
IndicatorsPages

1142. Instrument cluster
C-HR_OM_Europe_OM10528E
*1: These lights turn on when the engine switch is turned to the “ON” position
(vehicles without a smart entry & start system) or IGNITION ON mode
(vehicles with a smart entry & start system) to indicate that a system check
is being performed. They will turn off after the engine is started, or after a
few seconds. There may be a malfunction in a system if a light does not
come on, or if the lights do not turn off. Have the vehicle inspected by any
authorized retailer or Toyota authorized repairer, or any reliable repairer.
*2: Vehicles with monochrome display only
*3: Vehicles with a manual transmission
*4: In order to confirm operation, the BSM outside rear view mirror indicators
illuminate in the following situations:
• When the engine switch is turned to the “ON” position (vehicles without
a smart entry & start system) or IGNITION ON mode (vehicles with a
smart entry & start system), the BSM function is enabled on the
screen of the multi-information display.
• When the BSM function is enabled on the screen of the multi-
information display, the engine switch is turned to the “ON” position
(vehicles without a smart entry & start system) or IGNITION ON mode
(vehicles with a smart entry & start system).
If the system is functioning correctly, the BSM outside rear view mirror indi-
cators will turn off after a few seconds.
If the BSM outside rear view mirror indicators do not illuminate or do not
turn off, there may be a malfunction in the system.
If this occurs, have the vehicle inspected by any authorized Toyota retailer
or Toyota authorized repairer, or any reliable repairer.
*5: The light flashes to indicate that the system is operating.
*6: The light turns on when the system is off.

1152. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
Indicators and symbols displayed on the multi-information dis-
play
IndicatorsPages
*1, 2Brake hold operated indicator P. 262
*1, 2Brake hold standby indicator P. 262
*2LDA indicator (if equipped) P. 315
Speed limiter indicator (if equipped) P. 387
Cruise control indicator (if equipped)
P. 336,
351,
369
Cruise control “SET” indicator (if equipped)
P. 336,
351,
369
Radar cruise control indicator (if equipped) P. 336,
351
*2“SPORT” indicator P. 385
*2“ECO MODE” indicator P. 385
*3Eco Driving Indicator Light P. 118
*4Gear Shift Indicator P. 251

1162. Instrument cluster
C-HR_OM_Europe_OM10528E
*1: These lights turn on when the engine switch is turned to the “ON” position
(vehicles without a smart entry & start system) or IGNITION ON mode
(vehicles with a smart entry & start system) to indicate that a system check
is being performed. They will turn off after the engine is started, or after a
few seconds. There may be a malfunction in a system if a light does not
come on, or if the lights do not turn off. Have the vehicle inspected by any
authorized retailer or Toyota authorized repairer, or any reliable repairer.
*2: Vehicles with color display only
*3: Vehicles with a Multidrive
*4: Vehicles with a manual transmission
*2Stop & Start indicator (if equipped) P. 374
*2Speed limit sign (if equipped) P. 330
Low outside temperature indicator P. 120
IndicatorsPages

1172. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
*1: Vehicles with monochrome display
*2: Vehicles with color display
Symbols on multi-information displayPages
*1Open door warning light P. 697
Charging system warning light P. 693
Low engine oil pressure warning light P. 693
High engine coolant temperature warning light P. 698
LDA (Lane Departure Alert with steering con-
trol) (if equipped)
P. 698
P. 315
*2Smart entry & start system (if equipped) P. 236
*2Brake Override System/Drive-Start Control P. 699

1182. Instrument cluster
C-HR_OM_Europe_OM10528E
■Eco Driving Indicator Light (vehicles with a Multidrive)
Eco Driving Indicator Light will not operate in the following conditions:
● The shift lever is in anything other than D.
● The vehicle is being driven in “SPORT” mode (P. 385)
● The vehicle speed is approximately 130 km/h (80 mph) or higher.
During Eco-Friendly acceleration (Eco
driving), Eco Driving Indicator Light will
turn on. When the acceleration exceeds
Zone of Eco driving, and when the vehicle
is stopped, the light turns off.
Eco Driving Indicator Light availability can
be customized. The default setting is on.
( P. 779)
WARNING
■If a safety system warning light does not come on
Should a safety system light such as ABS and SRS airbag warning light not
come on when you start the engine, this could mean that these systems are
not available to help protect you in an accident, which could result in death
or serious injury. Have the vehicle inspected any authorized Toyota retailer
or Toyota authorized repairer, or any reliable repairer.

1212. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
Odometer and trip meter display
Displays the following items.
Odometer:
Displays the total distance the vehicle has been driven.
Trip meter:
Displays the distance the vehicle has been driven since the meter was last
reset. Trip meters A and B can be used to record and display different dis-
tances independently.
Maintenance required information:
Displays the remaining distance until the engine oil should be changed. If
“-” is displayed before distance, it means oil maintenance is overdue. Have
the engine oil changed by any authorized Toyota retailer or Toyota autho-
rized repairer, or any reliable repairer.
• Displays the maintenance required information when the engine switch
is turned to the “ON” position (vehicles without smart entry & start sys-
tem) or in IGNITION ON mode (vehicles with smart entry & start sys-
tem).
• Maintenance required information reset method ( P. 621)
Stop & Start system operation time (if equipped):
Displays the total amount of time that the engine has been stopped due to
operation of the Stop & Start system during the time of the current engine
stop.
Instrument cluster light control display (monochrome display):
Displays the meter light control display.
Shift position and shift range display (color display)
Displays the selected shift position or selected shift range. ( P. 244)
Engine coolant temperature gauge
Displays the engine coolant temperature.
6
7
8

1222. Instrument cluster
C-HR_OM_Europe_OM10528E
Switches the items of the odome-
ter and trip meter display by
pressing the “TRIP” switch.
When the trip meter is displayed,
pressing and holding the “TRIP”
switch will reset the trip meter.
The brightness of the instrument cluster lights (when the headlight
switch is on) can be adjusted.
Display the instrument cluster light
control by pressing the “TRIP”
switch.
Then, press and hold the switch.
Adjust the brightness to the
desired level by pressing the
switch.
Changing the display
Instrument cluster light control (monochrome display)

1262. Instrument cluster
C-HR_OM_Europe_OM10528E
●PCS (Pre-Collision System) (if equipped) (P. 298)
● LDA (Lane Departure Alert with steering control) (if equipped)
( P. 315)
The settings of the following items can be changed.
● Language
Select to change the language on the display. ( P. 779)
● Units
Select to change the units for measure of the fuel consumption.
( P. 779)
● Eco Driving Indicator Light (vehicles with a Multidrive)
Select to activate/deactivate the Eco Driving Indicator Light.
( P. 779)
● Tire pressure warning system (if equipped)
Select to initialize the tire pressure warning system. ( P. 634)
■When disconnecting and reconnecting battery terminals
The following information data will be reset:
● Elapsed time
● Average fuel consumption
● Driving range
● Average vehicle speed
■ Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liquid crystal displays, and there is no problem to continue
using the display.
■ Setting display automatic suspension
In the following situations, the setting display will be suspended.
● When a message appears
● When the vehicle begins to move
Vehicle settings
Meter settings