brake sensor TOYOTA CAMRY 1994 XV10 / 4.G Wiring Diagrams Workshop Manual

28
ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
[1MZ±FE]
A 2 A/C Triple Pressure SW (A/C Dual and Single Pressure F 1 Front Airbag Sensor LH
SW) F 2 Front Airbag Sensor RH
A 3 A/C Magnetic Clutch and Lock Sensor F 3 Front Clearance Light LH
A 4 ABS Actuator F 4 Front Clearance Light RH
A 5 ABS Actuator F 5 Front Side Marker LH
A 6 ABS Relay F 6 Front Side Marker RH
A 7 ABS Relay F 7 Front Turn Signal Light LH
A 8 ABS Speed Sensor Front LH F 8 Front Turn Signal Light RH
A 9 ABS Speed Sensor Front RH F 9 Front Wiper Motor
F 10 Fuse Box
B 2 Brake Fluid Level SW F 16 Fuse Box
F 18 Fuse Box
C 2 Cruise Control Actuator
C 17 Camshaft Position Sensor G 1 Generator (Alternator)
C 18 Crankshaft Position Sensor G 2 Generator (Alternator)
D 1 Data Link Connector 1 (Check Connector) H 1 Headlight Hi LH
D 2 Distributor H 2 Headlight Hi RH
H 3 Headlight Lo LH
E 1 EGR Gas Temp. Sensor H 4 Headlight Lo RH
E 2 Electronic Controlled Transmission Solenoid H 5 Horn LH
E 4 Engine Coolant Temp. Sensor (EFI Water Temp. H 6 Horn RH
Sensor) H 11 Heated Oxygen Sensor (Bank 1 Sensor 1)
E 5 Engine Coolant Temp. Sensor (Water Temp. Sensor) H 12 Heated Oxygen Sensor (Bank 2 Sensor 1)
(for Cooling Fan)

30
ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
[5S±FE]
A 1 A/C Condenser Fan Motor E 1 EGR Gas Temp. Sensor
A 2 A/C Triple Pressure SW (A/C Dual and Single Pressure E 2 Electronic Controlled Transmission Solenoid
SW) E 3 Electronic Controlled Transmission Solenoid
A 3 A/C Magnetic Clutch and Lock Sensor E 4 Engine Coolant Temp. Sensor (EFI Water Temp.
A 4 ABS Actuator Sensor)
A 5 ABS Actuator E 5 Water Temp. SW (for Cooling Fan)
A 6 ABS Relay
A 7 ABS Relay F 1 Front Airbag Sensor LH
A 8 ABS Speed Sensor Front LH F 2 Front Airbag Sensor RH
A 9 ABS Speed Sensor Front RH F 3 Front Clearance Light LH
F 4 Front Clearance Light RH
B 1 Back±Up Light SW (M/T) F 5 Front Side Marker LH
B 2 Brake Fluid Level SW F 6 Front Side Marker RH
F 7 Front Turn Signal Light LH
C 2 Cruise Control Actuator F 8 Front Turn Signal Light RH
F 9 Front Wiper Motor
D 1 Data Link Connector 1 (Check Connector) F 10 Fuse Box
D 2 Distributor F 16 Fuse Box
F 17 Fuse Box
F 18 Fuse Box
G 1 Generator (Alternator)
G 2 Generator (Alternator)

33
Position of Parts in Instrument Panel
G 3 Glove Box Light O 5 O/D Main SW and A/T Indicator Light (Shift Lever)
G 4 Glove Box Light SW
P 2 Parking Brake SW (for 1MZ±FE)
H 7 Hazard SW P 3 Parking Brake SW (for 5S±FE)
H 8 Heater Control SW (for Push Control SW Type) or Air P 4 Power Seat Control SW
Vent Mode Control SW (for Lever Control SW Type) P 5 Power Seat Motor (for Front Vertical Control)
H 9 Heated Oxygen Sensor (Bank 1 Sensor 2) P 6 Power Seat Motor (for Rear Vertical Control)
P 7 Power Seat Motor (for Reclining Control)
I 11 Ignition Key Cylinder Light P 8 Power Seat Motor (for Slide Control)
I 12 Ignition SW and Unlock Warning SW
I 13 Integration Relay R 2 Radio and Player (w/ CD Player)
R 3 Radio and Player (w/o CD Player)
J 1 Junction Connector R 4 Radio and Player (w/o CD Player)
J 2 Junction Connector R 5 Rear Window Defogger SW
J 3 Junction Connector R 6 Remote Control Mirror SW
J 4 Junction Connector (for SRS System) R 7 Rheostat
J 7 Junction Connector
S 5 Shift Lock ECU
K 3 Key Interlock Solenoid S 8 Stereo Component Amplifier
S 9 Stereo Component Amplifier
N 2 Noise Filter (for Stop Light) S 10 Stop Light SW
N 3 Noise Filter (for Stop Light)

39
Connector Joining Wire Harness and Wire Harness
CODEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EB1ENGINE ROOM MAIN WIRE AND RELAY WIRE (UNDER THE R/B NO. 5)
EC1ENGINE WIRE AND ENGINE ROOM MAIN WIRE (UNDER THE J/B NO. 1)
ED1COWL WIRE AND ENGINE ROOM MAIN WIRE (UNDER THE J/B NO. 1)
EE1SENSOR WIRE AND ENGINE WIRE (SIDE OF FRONT CYLINDER HEAD)
EF1ENGINE WIRE AND COWL WIRE (NEAR THE BRAKE MASTER CYLINDER)

54
POWER SOURCE (Current Flow Chart)
40A AM1
15A CIG/RADIO
40A DEFOG
15A ECU±1G
10A GAUGE
7.5A IGN
10A MIR±HTR
30A POWER
7.5A SRS
15A STOP
15A TAIL
7.5A TURN
20A WIPER
30A AM2
7.5A ALT±S
30A CDS FAN
20A DOME
15A ECU±B
15A EFI
10A HAZ
15A HEAD (LWR±LH)
15A HEAD (LWR±RH)
15A HEAD (UPR±LH)
15A HEAD (UPR±RH)
15A HEAD LH
15A HEAD RH
10A HORN
40A MAIN
7.5A OBD
10A STARTER
10A A/C
40A HEATER
7.5A DRL
100A ALT
60A ABS
A/C Condenser Fan Motor (5S±FE)
242
A4 A5 A11 A1*Page Nos. of
Related Systems
Parts
Code or
Location
CB or Fuse
LocationA2 A3
* These are the page numbers of the first page on which the related system is shown.
The part indicated is located somewhere in the system, not necessarily on the page indicated here.


A12 A6 A7 A13 A17 A18A14 A16 A21 B1 B2 B3 B4 B5 B6 B7 B9 B10 214 252126
252210 210 246246
252126222
224152 236 166246
252246
252126
246
252160
166 220 220
A/C Triple Pressure SW (A/C Dual
and Single Pressure SW)
A/C Magnetic Clutch and Lock
Sensor
ABS Actuator and ECU
(TMM Made)
ABS Actuator (TMC Made)
ABS Actuator and ECU
(TMM Made)
ABS Relay
A/C Amplifier
A/C SW
ABS ECU (TMC Made)
Air Inlet Control Servo Motor
Air Vent Mode Control Servo Motor
Ashtray Illumination
Auto Antenna Motor and Relay
Back±Up Light SW (M/T)
Brake Fluid Level SW
Back Door Lock Control SW
Blower Motor
Blower Resistor
Blower SW
Buckle SW LH
Back Door Lock Motor (W/G)
Buckle SW RH
A10246
252 210 210 210 214 246
252 242
246
252
ABS ECU (TMC Made)A/C Evaporator Temp. Sensor ABS Relay
[LOCATION](1)
(7): J/B No. 1 (See page 20)
: R/B No. 7 (See page )(2)
(8): J/B No. 2 (See page 19)
: Fuse Box (F10, F17 See
on page )(3): R/B No. 1 (See page 23)
2022
25
27
28 29

59
11 8
180
186
22480
J5 J6 K3
120
124
144
148168 198130
138
168168120
124
182
192198
204
210
214236
Junction Connector (W/G)
Junction Connector (1MZ±FE)
Key Interlock Solenoid
License Plate Light
Light Failure Sensor
Luggage Compartment Light
Luggage Compartment Light SW
Moon Roof Control RelayMoon Roof Control SW and Personal
Light (w/ Moon Roof) (EX. W/G)Moon Roof Limit SW (EX. W/G)
Moon Roof Motor (EX. W/G)
Mass Air Flow (Air Flow Meter)
(1MZ±FE)
Noise Filter (for Ignition System)
Oil Pressure SW
O/D Main SW and A/T Indicator
Light (Shift Lever)
Park/Neutral Position SW
(Neutral Start SW) (A/T)
Parking Brake SW (for 1MZ±FE)
Parking Brake SW (for 5S±FE)
J7 L1 L2 L4L3 M2 M3 M5M4 M6 N1 N2 N3 O1 O5 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12
Junction Connector (1MZ±FE)
Noise Filter (for Stop Light)
Noise Filter (for Stop Light)
Power Seat Control SW
Power Seat Motor
(for Front Vertical Control)
Power Seat Motor
(for Rear Vertical Control)
Power Seat Motor
(for Slide control)
Power Seat Motor
(for Reclining Control)
Power Window Control SW Front
RH
Power Window Control SW Rear
LH (EX. C/P)
Power Window Control SW Rear
RH (EX. C/P)
Power Window Master SW and
Door Lock control SW LH
182 144130
134
138
140130
134
138
140168 80 80120
124
182
192198
204
210
214126
198
204 68
72
152
198
204236 236 180 180 180 180 180 156 156 156156
160
(4): R/B No. 4 (See page 20)(5): R/B No. 5 (See page 19)(6)R/B No. 6 (See Page )
2526 26

121
CURRENT IS APPLIED AT ALL TIMES THROUGH A STOP FUSE TO TERMINAL 2 OF THE STOP LIGHT SW.
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 8 OF THE LIGHT FAILURE
SENSOR, AND ALSO FLOWS THROUGH THE REAR LIGHT WARNING LIGHT TO TERMINAL 4 OF THE LIGHT FAILURE SENSOR.
STOP LIGHT DISCONNECTION WARNING
WHEN THE IGNITION SW IS TURNED ON AND THE BRAKE PEDAL IS PRESSED (STOP LIGHT SW ON), IF THE STOP LIGHT CIRCUIT IS
OPEN, THE CURRENT FLOWING FROM TERMINALS 7 OF THE LIGHT FAILURE SENSOR TO TERMINALS 1, 2 CHANGES, SO THE
LIGHT FAILURE SENSOR DETECTS THE DISCONNECTION AND THE WARNING CIRCUIT OF THE LIGHT FAILURE SENSOR IS
ACTIVATED.
AS A RESULT, THE CURRENT FLOWS FROM TERMINAL 4 OF THE LIGHT FAILURE SENSOR " TERMINAL 11 " GROUND AND TURNS
THE REAR LIGHT WARNING LIGHT ON. BY PRESSING THE BRAKE PEDAL, THE CURRENT FLOWING TO TERMINAL 8 OF THE LIGHT
FAILURE SENSOR KEEPS THE WARNING CIRCUIT ON HOLD AND THE WARNING LIGHT ON UNTIL THE IGNITION SW IS TURNED OFF.
S10 STOP LIGHT SW
2±1 : CLOSED WITH BRAKE PEDAL DEPRESSED
L 2 LIGHT FAILURE SENSOR
1, 2, 7±GROUND : APPROX. 12 VOLTS WITH STOP LIGHT SW ON
4, 8±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
11±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 932N 2A33R1034 (S/D), 35 (C/P)
H1034 (S/D), 35 (C/P)N 3B33R1134 (S/D), 35 (C/P)
J 133R 834 (S/D), 35 (C/P)S1033
L 234 (S/D), 35 (C/P)R 934 (S/D), 35 (C/P)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IJ142FLOOR NO. 1 WIRE AND COWL WIRE
BZ146 (S/D)LUGGAGE ROOM NO 1 WIRE AND FLOOR NO 1 WIREBZ148 (C/P)LUGGAGE ROOM NO. 1 WIRE AND FLOOR NO. 1 WIRE
Ba146 (S/D)FLOOR NO 1 WIRE AND LUGGAGE ROOM NO 2 WIREBa148 (C/P)FLOOR NO. 1 WIRE AND LUGGAGE ROOM NO. 2 WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
46 (S/D)
BL48 (C/P)UNDER THE LEFT QUARTER PILLARBL
50 (W/G)
UNDER THE LEFT QUARTER PILLAR
BQ50 (W/G)LOWER BACK PANEL CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
B 946 (S/D)FLOOR NO 1 WIREB1746 (S/D)LUGGAGE ROOM NO. 2 WIRE
B1046 (S/D)FLOOR NO. 1 WIREB2548 (C/P)FLOOR NO 1 WIREB12B2648 (C/P)FLOOR NO. 1 WIRE
B1346 (S/D)LUGGAGE ROOM NO. 1 WIREB2848 (C/P)LUGGAGE ROOM NO. 1 WIRE
B14
46 (S/D)LUGGAGE ROOM NO. 1 WIRE
B2948 (C/P)LUGGAGE ROOM NO. 2 WIRE
B1646 (S/D)LUGGAGE ROOM NO. 2 WIRE
SYSTEM OUTLINE
SERVICE HINTS

125
CURRENT IS APPLIED AT ALL TIMES THROUGH A STOP FUSE TO TERMINAL 2 OF THE STOP LIGHT SW.
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 8 OF THE LIGHT FAILURE
SENSOR, AND ALSO FLOWS THROUGH THE REAR LIGHT WARNING LIGHT TO TERMINAL 4 OF THE LIGHT FAILURE SENSOR.
STOP LIGHT DISCONNECTION WARNING
WHEN THE IGNITION SW IS TURNED ON AND THE BRAKE PEDAL IS PRESSED (STOP LIGHT SW ON), IF THE STOP LIGHT CIRCUIT IS
OPEN, THE CURRENT FLOWING FROM TERMINALS 7 OF THE LIGHT FAILURE SENSOR TO TERMINALS 1, 2 CHANGES, SO THE
LIGHT FAILURE SENSOR DETECTS THE DISCONNECTION AND THE WARNING CIRCUIT OF THE LIGHT FAILURE SENSOR IS
ACTIVATED.
AS A RESULT, THE CURRENT FLOWS FROM TERMINAL 4 OF THE LIGHT FAILURE SENSOR " TERMINAL 11 " GROUND AND TURNS
THE REAR LIGHT WARNING LIGHT ON. BY PRESSING THE BRAKE PEDAL, THE CURRENT FLOWING TO TERMINAL 8 OF THE LIGHT
FAILURE SENSOR KEEPS THE WARNING CIRCUIT ON HOLD AND THE WARNING LIGHT ON UNTIL THE IGNITION SW IS TURNED OFF.
S10 STOP LIGHT SW
2±1 : CLOSED WITH BRAKE PEDAL DEPRESSED
L 2 LIGHT FAILURE SENSOR
1, 2, 7±GROUND : APPROX. 12 VOLTS WITH STOP LIGHT SW ON
4, 8±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
11±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 932L 236 (W/G)R 936 (W/G)
H1036 (W/G)N 2A33R1036 (W/G)
J 133N 3B33R1136 (W/G)
J 536 (W/G)R 836 (W/G)S1033
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IJ142FLOOR NO. 1 WIRE AND COWL WIRE
Bb150 (W/G)LUGGAGE ROOM NO. 1 WIRE AND FLOOR NO. 1 WIRE
Bc250 (W/G)BACK DOOR NO. 1 WIRE AND FLOOR NO. 1 WIRE
Bd250 (W/G)BACK DOOR NO. 1 WIRE AND BACK DOOR NO. 2 WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
46 (S/D)
BL48 (C/P)UNDER THE LEFT QUARTER PILLARBL
50 (W/G)
UNDER THE LEFT QUARTER PILLAR
BQ50 (W/G)LOWER BACK PANEL CENTER
BR50 (W/G)BACK DOOR CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
B3650 (W/G)FLOOR NO. 1 WIREB3850 (W/G)BACK DOOR NO. 2 WIRE
SYSTEM OUTLINE
SERVICE HINTS

192
CRUISE CONTROL
B
ST1 IG1 ACC
AM1
7
IP3 8IP3 11
II1 4 2 1
1 1 213 41883
17 15
20 1420 510 2
13B 4 B 12 B5B9 A 6
1 2
IG CC
I13
11 R±L R±L
R±L
W±B
W±B W±B
B±R B±W
R±L B±W
B±R B
B
W±B
W±L
W
LG±R
R±W LG±R
R±W LG±R
R±W
R±WW±B
W±B
G±BG
V±Y
G±Y V±YP LG B
FROM POWER SOURCE SYSTEM(
SEEPAGE64)
10A
GAUGE
COMBINATON METER
DIODE
(
FOR CRUISE
CONTROL)VEHICLE
SPEED SENSOR
(
SPEED SENSOR)
DATA LINK CONNECTOR 2
(
TDCL)
A/D JUNCTION
CONNECTOR
CRUISE CONTROL
CLUTCH SW
(
M/T)
CRUISE CONTROL SW
[COMB. SW]
DA TA LINK CONNE CTOR 1
(
CHECK CONNECTOR)
PARKING
BRAKE SW
PARKING
BRAKE SWMAIN
CA NCELSET/
COAST RE SUME/
ACCEL N&C GND CMS CCS TC PKBBSPD PI
TC
IGNITION SW
P
N5
6EF1 1
B±W B±W
J1
P1
D5
C8 , C9
D3
V5A
PARK/NEUTRAL POSITION SW
(
NE UTRAL S TA RT SW)
(
A/T) B
TO STARTER RELAY
CRUIS E CONTROL ECU C16
C15
C13
D1
P3
P2
(
1MZ±FE)
SPEED
CRUISEI12
IP3 2
(
A/T)
(
5S±FE)IP3 14
(
A/T)
(
M/T) (
M/T)
R±L
TO BA CK ±UP LIGHT SW(
M/T)
TO PARK/NEUTRAL POSITION SW
(
NE UTRA L S TA RT SW)(
A/T)
TO GENERATOR(
ALTERNATOR)
R±L
I18
(
*2) O
(
*1)
G±L
(
*2) O
(
*1)
O
(
*1) G±L
(
*2)
1G 63C16
1A 14 3B16 1E 5
1A 71D61B6 15A
ECU±IG
3D 22 3B8
3B 10 3B19 3B9
3B 73B18
3B 17
3B 14 3B5
3C 18
1M1
1C11
3B 12
3D 83C83B 15
3D 16

196
CRUISE CONTROL
CURRENT IS APPLIED AT ALL TIMES THROUGH STOP FUSE TO TERMINAL 1 OF THE CRUISE CONTROL ECU AND TERMINAL 2 OF
STOP LIGHT SW, AND ALSO THROUGH THE STOP FUSE TO TERMINAL 15 OF CRUISE CONTROL ECU.
WITH THE IGNITION SW TURNED TO ON, THE CURRENT FLOWS THROUGH GAUGE FUSE TO TERMINAL (A) 6 OF COMBINATION
METER AND THE CURRENT THROUGH ECU±IG FUSE FLOWS TO TERMINAL 14 OF CRUISE CONTROL ECU.
WHEN THE IGNITION SW IS ON AND THE CRUISE CONTROL MAIN SW IS TURNED ON, A SIGNAL IS INPUT FROM TERMINAL 15 OF
CRUISE CONTROL MAIN SW TO TERMINAL 4 OF CRUISE CONTROL ECU. AS A RESULT, THE CRUISE CONTROL ECU FUNCTIONS
AND THE CURRENT TO TERMINAL 14 OF CRUISE CONTROL ECU TO TERMINAL 13 OF CRUISE CONTROL ECU " GROUND, AND
THE CRUISE CONTROL SYSTEM IS IN A CONDITION READY FOR OPERATION.
AT THE SAME TIME, THE CURRENT THROUGH THE GAUGE FUSE FLOWS FROM TERMINAL (A) 6 OF CRUISE CONTROL INDICATOR
LIGHT " TERMINAL (B) 9 " TERMINAL 5 OF CRUISE CONTROL ECU " TERMINAL 13 " TO GROUND, CAUSING THE CRUISE
CONTROL INDICATOR LIGHT TO LIGHT UP, INDICATING THAT THE CRUISE CONTROL IS READY FOR OPERATION.
1. SET OPERATION
WHEN THE CRUISE CONTROL MAIN SW IS TURNED ON AND THE SET SW IS TURNED ON WITH THE VEHICLE SPEED WITHIN THE
SET LIMIT (APPROX. 40 KM/H, 25 MPH TO 200 KM/H, 124 MPH), A SIGNAL IS INPUT TO TERMINAL 18 OF THE CRUISE CONTROL ECU
AND THE VEHICLE SPEED AT THE TIME THE SET SW IS RELEASED IS MEMORIZED IN THE ECU AS THE SET SPEED.
2. SET SPEED CONTROL
DURING CRUISE CONTROL DRIVING, THE ECU COMPARES THE SET SPEED MEMORIZED IN THE ECU WITH THE ACTUAL VEHICLE
SPEED INPUT INTO TERMINAL 20 OF THE CRUISE CONTROL ECU FROM THE VEHICLE SPEED SENSOR (SPEED SENSOR), AND
CONTROLS THE CRUISE CONTROL ACTUATOR TO MAINTAIN THE SET SPEED.
WHEN THE ACTUAL SPEED IS LOWER THAN THE SET SPEED, THE ECU CAUSES THE CURRENT TO THE CRUISE CONTROL
ACTUATOR TO FLOW FROM TERMINAL 12" TERMINAL 6 OF CRUISE CONTROL ACTUATOR "TERMINAL 7 "TERMINAL 11 OF
CRUISE CONTROL ECU. AS A RESULT, THE MOTOR IN THE CRUISE CONTROL ACTUATOR IS ROTATED TO OPEN THE THROTTLE
VALVE AND THE THROTTLE CABLE IS PULLED TO INCREASE THE VEHICLE SPEED. WHEN THE ACTUAL DRIVING SPEED IS HIGHER
THAN THE SET SPEED, THE CURRENT TO CRUISE CONTROL ACTUATOR FLOWS FROM TERMINAL 11 OF ECU "TERMINAL 7 OF
CRUISE CONTROL ACTUATOR "TERMINAL 6 "TERMINAL 12 OF CRUISE CONTROL ECU.
THIS CAUSES THE MOTOR IN THE CRUISE CONTROL ACTUATOR TO ROTATE TO CLOSE THE THROTTLE VALVE AND RETURN THE
THROTTLE CABLE TO DECREASE THE VEHICLE SPEED.
3. COAST CONTROL
DURING THE CRUISE CONTROL DRIVING, WHILE THE COAST SW IS ON, THE CRUISE CONTROL ACTUATOR RETURNS THE
THROTTLE CABLE TO CLOSE THE THROTTLE VALVE AND DECREASE THE DRIVING SPEED. THE VEHICLE SPEED WHEN THE COAST
SW IS TURNED OFF IS MEMORIZED AND THE VEHICLE CONTINUES AT THE NEW SET SPEED.
4. ACCEL CONTROL
DURING CRUISE CONTROL DRIVING, WHILE THE ACCEL SW IS TURNED ON, THE CRUISE CONTROL ACTUATOR PULLS THE
THROTTLE CABLE TO OPEN THE THROTTLE VALVE AND INCREASE THE DRIVING SPEED.
THE VEHICLE SPEED WHEN THE ACCEL SW IS TURNED OFF IS MEMORIZED AND THE VEHICLE CONTINUES AT THE NEW SET
SPEED.
5. RESUME CONTROL
UNLESS THE VEHICLE SPEED FALLS BELOW THE MINIMUM SPEED LIMIT (APPROX. 40 KM/H, 25 MPH) AFTER CANCELING THE SET
SPEED BY THE CANCEL SW, PUSHING THE RESUME SW WILL CAUSE THE VEHICLE TO RESUME THE SPEED SET BEFORE
CANCELLATION.
6. MANUAL CANCEL MECHANISM
IF ANY OF THE FOLLOWING OPERATIONS OCCURS DURING CRUISE CONTROL OPERATION, CURRENT FLOW TO MAGNETIC
CLUTCH OF THE ACTUATOR IS CUT TURNS OFF AND THE MOTOR ROTATES TO CLOSE THE THROTTLE VALVE AND THE CRUISE
CONTROL IS RELEASED.
*PLACING THE SHIFT LEVER IN ªNº POSITION (PARK/NEUTRAL POSITION SW (NEUTRAL START SW ON). ªSIGNAL INPUT TO
TERMINAL 2 OF ECUº (A/T)
*DEPRESSING THE CLUTCH PEDAL (CLUCH SW ON). ªSIGNAL INPUT TO TERMINAL 2 OF THE ECUº (M/T)
*DEPRESSING THE BRAKE PEDAL (STOP LIGHT SW ON). ªSIGNAL INPUT TO TERMINAL 16 OF ECUº
*PUSH THE CANCEL SW (CANCEL SW ON). ªSIGNAL INPUT TO TERMINAL 18 OF ECUº
*DEPRESSING THE PARKING BRAKE PEDAL (PARKING BRAKE SW ON). ªSIGNAL INPUT TO TERMINAL 3 OF ECUº (3VZ±FE)
*PULLING THE PARKING BRAKE LEVER (PARKING BRAKE SW ON). ªSIGNAL INPUT TO TERMINAL 3 OF THE ECUº (5S±FE)
SYSTEM OUTLINE