condenser TOYOTA CAMRY 1994 XV10 / 4.G Wiring Diagrams Workshop Manual

METER, ANALOG
Current flow activates a magnetic
coil which causes a needle to
move, thereby providing a relative
display against a background
calibration. LED (LIGHT EMITTING DIODE)
Upon current flow, these diodes
emit light without producing the
heat of a comparable light. IGNITION COIL
Converts low±voltage DC current
into high±voltage ignition current
for firing the spark plugs. 1. SINGLE
FILAMENT
GROUND
The point at which wiring attaches
to the Body, thereby providing a
return path for an electrical circuit;
without a ground, current cannot
flow.Current flow causes a headlight
filament to heat up and emit light.
A headlight may have either a
single (1) filament or a double (2)
filament. BATTERY
Stores chemical energy and
converts it into electrical energy.
Provides DC current for the auto's
various electrical circuits.
CAPACITOR (Condenser)
A small holding unit for temporary
storage of electrical voltage.
CIRCUIT BREAKER
Basically a reusable fuse, a circuit
breaker will heat and open if too
much current flows through it. Some
units automatically reset when cool,
others must be manually reset.
DIODE
A semiconductor which allows
current flow in only one direction.
DIODE, ZENER
A diode which allows current flow
in one direction but blocks reverse
flow only up to a specific voltage.
Above that potential, it passes the
excess voltage. This acts as a
simple voltage regulator.
FUSE
A thin metal strip which burns
through when too much current
flows through it, thereby stopping
current flow and protecting a
circuit from damage.
FUSIBLE LINK
A heavy±gauge wire placed in
high amperage circuits which
burns through on overloads,
thereby protecting the circuit.
The numbers indicate the cross±
section surface area of the wires.HORN
An electric device which sounds a
loud audible signal.
LIGHT
Current flow through a filament
causes the filament to heat up
and emit light.
METER, DIGITAL
Current flow activates one or
many LED's, LCD's, or fluorescent
displays, which provide a relative
or digital display.
MOTOR
A power unit which converts
electrical energy into mechanical
energy, especially rotary motion. CIGARETTE LIGHTER
An electric resistance heating
element.
DISTRIBUTOR, IIA
Channels high±voltage current
from the ignition coil to the
individual spark plugs.2. DOUBLE
FILAMENT HEADLIGHTS
FUEL
(for High Current Fuse or
Fusible Link.)
(for Medium Current Fuse)
M
16
GLOSSARY OF TERMS AND SYMBOLS

30
ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
[5S±FE]
A 1 A/C Condenser Fan Motor E 1 EGR Gas Temp. Sensor
A 2 A/C Triple Pressure SW (A/C Dual and Single Pressure E 2 Electronic Controlled Transmission Solenoid
SW) E 3 Electronic Controlled Transmission Solenoid
A 3 A/C Magnetic Clutch and Lock Sensor E 4 Engine Coolant Temp. Sensor (EFI Water Temp.
A 4 ABS Actuator Sensor)
A 5 ABS Actuator E 5 Water Temp. SW (for Cooling Fan)
A 6 ABS Relay
A 7 ABS Relay F 1 Front Airbag Sensor LH
A 8 ABS Speed Sensor Front LH F 2 Front Airbag Sensor RH
A 9 ABS Speed Sensor Front RH F 3 Front Clearance Light LH
F 4 Front Clearance Light RH
B 1 Back±Up Light SW (M/T) F 5 Front Side Marker LH
B 2 Brake Fluid Level SW F 6 Front Side Marker RH
F 7 Front Turn Signal Light LH
C 2 Cruise Control Actuator F 8 Front Turn Signal Light RH
F 9 Front Wiper Motor
D 1 Data Link Connector 1 (Check Connector) F 10 Fuse Box
D 2 Distributor F 16 Fuse Box
F 17 Fuse Box
F 18 Fuse Box
G 1 Generator (Alternator)
G 2 Generator (Alternator)

54
POWER SOURCE (Current Flow Chart)
40A AM1
15A CIG/RADIO
40A DEFOG
15A ECU±1G
10A GAUGE
7.5A IGN
10A MIR±HTR
30A POWER
7.5A SRS
15A STOP
15A TAIL
7.5A TURN
20A WIPER
30A AM2
7.5A ALT±S
30A CDS FAN
20A DOME
15A ECU±B
15A EFI
10A HAZ
15A HEAD (LWR±LH)
15A HEAD (LWR±RH)
15A HEAD (UPR±LH)
15A HEAD (UPR±RH)
15A HEAD LH
15A HEAD RH
10A HORN
40A MAIN
7.5A OBD
10A STARTER
10A A/C
40A HEATER
7.5A DRL
100A ALT
60A ABS
A/C Condenser Fan Motor (5S±FE)
242
A4 A5 A11 A1*Page Nos. of
Related Systems
Parts
Code or
Location
CB or Fuse
LocationA2 A3
* These are the page numbers of the first page on which the related system is shown.
The part indicated is located somewhere in the system, not necessarily on the page indicated here.


A12 A6 A7 A13 A17 A18A14 A16 A21 B1 B2 B3 B4 B5 B6 B7 B9 B10 214 252126
252210 210 246246
252126222
224152 236 166246
252246
252126
246
252160
166 220 220
A/C Triple Pressure SW (A/C Dual
and Single Pressure SW)
A/C Magnetic Clutch and Lock
Sensor
ABS Actuator and ECU
(TMM Made)
ABS Actuator (TMC Made)
ABS Actuator and ECU
(TMM Made)
ABS Relay
A/C Amplifier
A/C SW
ABS ECU (TMC Made)
Air Inlet Control Servo Motor
Air Vent Mode Control Servo Motor
Ashtray Illumination
Auto Antenna Motor and Relay
Back±Up Light SW (M/T)
Brake Fluid Level SW
Back Door Lock Control SW
Blower Motor
Blower Resistor
Blower SW
Buckle SW LH
Back Door Lock Motor (W/G)
Buckle SW RH
A10246
252 210 210 210 214 246
252 242
246
252
ABS ECU (TMC Made)A/C Evaporator Temp. Sensor ABS Relay
[LOCATION](1)
(7): J/B No. 1 (See page 20)
: R/B No. 7 (See page )(2)
(8): J/B No. 2 (See page 19)
: Fuse Box (F10, F17 See
on page )(3): R/B No. 1 (See page 23)
2022
25
27
28 29

185
WITH THE IGNITION SW TURNED ON, THE CURRENT FLOWS TO TERMINAL 18 OF THE WIPER AND WASHER SW, TERMINAL 2 OF
THE WASHER MOTOR AND TERMINAL 4 OF THE WIPER MOTOR THROUGH THE WIPER FUSE.
1. LOW SPEED POSITION
WITH WIPER SW TURNED TO LOW POSITION, THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " WIPER MOTOR " TERMINAL 1 " TO GROUND AND CAUSES TO THE WIPER
MOTOR TO RUN AT LOW SPEED.
2. HIGH SPEED POSITION
WITH WIPER SW TURNED TO HIGH POSITION, THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 13 " TERMINAL 2 OF THE WIPER MOTOR " WIPER MOTOR " TERMINAL 1 " TO GROUND AND CAUSES TO THE WIPER
MOTOR TO RUN AT HIGH SPEED.
3. INT POSITION
WITH WIPER SW TURNED TO INT POSITION, THE RELAY OPERATES AND THE CURRENT WHICH IS CONNECTED BY RELAY
FUNCTION FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW " TERMINAL 16 " TO GROUND. THIS FLOW OF CURRENT
OPERATES THE INTERMITTENT CIRCUIT AND THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " TERMINAL 1 " TO GROUND AND THE WIPER FUNCTIONS.
THE INTERMITTENT OPERATION IS CONTROLLED BY A CONDENSER'S CHARGED AND DISCHARGED FUNCTION INSTALLED IN
RELAY AND THE INTERMITTENT TIME IS CONTROLLED BY A TIME CONTROL SW TO CHANGE THE CHARGING TIME OF THE
CONDENSER.
4. WASHER CONTINUOUS OPERATION
WITH WASHER SW TURNED TO ON, THE CURRENT FLOWS FROM TERMINAL 2 OF THE WASHER MOTOR " TERMINAL 1 "
TERMINAL 8 OF THE WIPER AND WASHER SW " TERMINAL 16 " TO GROUND AND CAUSES TO THE WASHER MOTOR TO RUN AND
WINDOW WASHER TO JET. THIS CAUSES THE CURRENT TO FLOW TO WASHER CONTINUOUS OPERATION CIRCUIT IN TERMINAL 18
OF THE WIPER AND WASHER SW " TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " TERMINAL 1 " TO GROUND AND THE
WIPER FUNCTION.
C13 FRONT WIPER AND WASHER SW (W/ WIPER RELAY) [COMB. SW]
16±GROUND : ALWAYS CONTINUITY
18±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
7±GROUND : APPROX. 12 VOLTS WITH WIPER AND WASHER SW AT LOW OR MIST POSITION
APPROX. 12 VOLTS 2 TO 12 SECONDS INTERMITTENTLY WITH WIPER SW AT INT POSITION
4±GROUND : APPROX. 12 VOLTS WITH IGNITION SW ON UNLESS WIPER MOTOR AT STOP POSITION
13±GROUND : APPROX. 12 VOLTS WITH WIPER AND WASHER SW AT HIGH POSITION
F 9 FRONT WIPER MOTOR
5±6 : CLOSED UNLESS WIPER MOTOR AT STOP POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1332F 928 (1MZ±FE), 30 (5S±FE)W 128 (1MZ±FE), 30 (5S±FE)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IR144ENGINE ROOM MAIN WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA38 (1MZ±FE)FRONT RIGHT FENDEREA40 (5S±FE)FRONT RIGHT FENDER
IE42LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E138 (1MZ±FE)ENGINE ROOM MAIN WIREI 544COWL WIREE 140 (5S±FE)ENGINE ROOM MAIN WIRE
SYSTEM OUTLINE
SERVICE HINTS

187
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS TO TERMINAL 2 OF WASHER MOTOR, TERMINAL 4 OF REAR WIPER
RELAY AND TERMINAL 1 OF REAR WIPER MOTOR THROUGH THE WIPER FUSE.
1. REAR WIPER NORMAL OPERATION
WITH THE IGNITION SW TURNED ON AND REAR WIPER AND WASHER SW TURNED ON, THE CURRENT FLOWING TO TERMINAL 4
OF REAR WIPER RELAY FLOWS TO TERMINAL 6 OF RELAY " TERMINAL 1 OF REAR WIPER AND WASHER SW " TERMINAL 16 "
TO GROUND. THUS, THE RELAY COIL IS ACTIVATED AND THE CURRENT TO TERMINAL 4 OF RELAY FLOWS TO TERMINAL 1 "
TERMINAL 4 OF REAR WIPER MOTOR " MOTOR " TERMINAL 2 " TO GROUND AND CAUSES THE MOTOR TO OPERATE THE
WIPER.
2. REAR WIPER INTERMITTENT OPERATION
WITH THE IGNITION SW TURNED ON AND REAR WIPER AND WASHER SW TURNED TO INT POSITION, THE CURRENT FLOWING TO
TERMINAL 4 OF REAR WIPER RELAY FLOWS TO TERMINAL 3 OF RELAY " TERMINAL 10 OF WIPER SW " TERMINAL 16 " TO
GROUND. AS A RESULT, THE RELAY OPERATES AND CURRENT FLOWS FROM TERMINAL 4 OF RELAY " TERMINAL 1 " TERMINAL
4 OF REAR WIPER MOTOR " MOTOR " TERMINAL 2 " TO GROUND, CAUSING THE MOTOR TO ROTATE TO OPERATE THE WIPER.
AT THIS TIME THE CONTACT IN THE WIPER MOTOR CLOSED AND THE CURRENT FLOWS FROM TERMINAL 1 OF REAR WIPER
MOTOR " TERMINAL 3 " TERMINAL 2 OF REAR WIPER RELAY " TERMINAL 1 " TERMINAL 4 OF REAR WIPER MOTOR "
TERMINAL 2 " TO GROUND.
THUS, THE INTERMITTENT±STOP CIRCUIT OPERATES, THE CONDENOR IN THE CIRCUIT CHARGES AND THE WIPER CONTINUES TO
OPERATE UNTIL REACHING THE STOP POSITION. AFTER THE WIPER STOPS, CURRENT DOES NOT FLOW TO THE
INTERMITTENT±STOP CIRCUIT FROM TERMINAL 2 OF RELAY, BUT THE CONDENSER DISCHARGES CURRENT INTO THE
INTERMITTENT CIRCUIT AND THE CIRCUIT OPERATES UNTIL THE CONDENSER DISCHARGE ENDS. AS A RESULT, THIS DISCHARGE
INTERVAL BECOMES THE INTERMITTENT TIME.
WHEN THE CURRENT IS DISCHARGED COMPLETELY, THE CURRENT FLOWING TO TERMINAL 4 OF RELAY FLOWS TO TERMINAL 3
" TERMINAL 10 OF REAR WIPER AND WASHER SW " TERMINAL 16 " TO GROUND.
THEN, THE CURRENT IN TERMINAL 4 OF RELAY FLOWS FROM TERMINAL 1 " TERMINAL 4 OF MOTOR " MOTOR " TERMINAL 2 "
TO GROUND AND ROTATES THE MOTOR. THROUGH REPEITION OF THIS PROCESS, INTERMITTENT OPERATION OF THE REAR
WIPER OCCURS.
3. WASHER OPERATION
WITH THE IGNITION SW ON AND THE REAR WIPER AND WASHER SW IS TURNED STRONGLY (WASHER SW ON), CURRENT FLOWS
FROM TERMINAL 2 OF WASHER MOTOR " TERMINAL 3 " TERMINAL 2 OF REAR WIPER AND WASHER SW " TERMINAL 16 " TO
GROUND SO THAT THE WASHER MOTOR ROTATES AND WINDOW WASHER EJECTS THE SPRAY, ONLY THE WHILE THE REAR
WASHER SW IS TURNED, WHEN THE REAR WIPER SW IS OFF, AND THE REAR WIPER AND WASHER SW IS THEN TURNED IN THE
OFF DIRECTION, WASHER LIQUID WILL ALSO SPLAY.
R19 REAR WIPER RELAY
4±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
7±GROUND : ALWAYS CONTINUITY
1±4 : POINTS CHANGES EVERY APPROX. 9±15 SECONDS INTERMITTENTLY WITH IGNITION SW ON AND WIPER SW AT
INT POSITION
W 1 WASHER MOTOR
2±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
3±GROUND : CONTINUITY WITH WASHER SW TURNED ON
SYSTEM OUTLINE
SERVICE HINTS

241
RADIATOR FAN AND CONDENSER FAN (5S±FE)
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A 130E 530 (5S±FE)
A 230 (5S±FE)R 130 (5S±FE)
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
526R/B NO. 5 (ENGINE COMPARTMENT LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
2B22ENGINE ROOM MAIN WIRE AND J/B NO 2 (ENGINE COMPARTMENT LEFT)2E22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3A24COWL WIRE AND J/B NO 3 (BEHIND COMBINATION METER)3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EA140 (5S±FE)ENGINE ROOM MAIN WIRE AND ENGINE ROOM NO. 3 WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EB40 (5S±FE)FRONT LEFT FENDER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E 540 (5S±FE)ENGINE ROOM MAIN WIRE

242
RADIATOR FAN AND CONDENSER FAN (5S±FE)
2B 12E82B32E6
55 55
55 55 2G 6
2E5
1 2EA1 1
M
1 2M
1 2
E5 5
EB EB
W±B W±B B±R B±R L±B
B±R
L
B W±B
W±R R WB±O B±R
W±B W±B
L
B±R
BW±BW±B
B±W
OM POWER SOURCE SYSTEM(
SEE PAGE 64)
30A
RDI FAN
24 13
4
FROM A/C
MAGNETIC
CLUTCH RELAY RADIATOR
FAN RELAY
RADIATOR
FAN RELAY
NO. 2
RADIATOR
FAN RELAY
NO. 3
A/C SINGLE
PRESSURE SW
WATER
TEMP. SW
(
FOR COOLING
FA N)RADIATOR
FAN MOTORA/C CONDE NSE R
FAN MOTOR A1
A2
R1
E532 51 15 23
3 2
EA1 2
1A 7FR
15A
ECU±IG
3A 153C 16
2B 40A
CDS FAN
3

243
FAN MOTOR OPERATION
WITH THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM ECU±IG FUSE TO RADIATOR FAN RELAY NO. 1 (COIL SIDE) AND
RADIATOR FAN RELAY NO. 2 (COIL SIDE) " TERMINAL 2 OF THE A/C SINGLE PRESSURE SW " TERMINAL 3 " TERMINAL 2 OF THE
WATER TEMP. SW " TERMINAL 1 " GROUND, AND RADIATOR FAN RELAY NO. 1 AND NO. 2 ARE TURNED ON.
*RADIATOR FAN MOTOR OPERATION
WHEN THE IGNITION SW IS TURNED ON, RADIATOR FAN RELAY NO. 1 IS TURNED ON. IF AT THIS TIME THE ENGINE COOLANT
TEMPERATURE IS APPROX. 90°C (194°F) OR HIGHER, THE WATER TEMP. SW IS TURNED OFF, RADIATOR FAN RELAY NO. 1 IS
TURNED OFF.
AS A RESULT, CURRENT FROM THE RDI FAN FUSE TO RADIATOR FAN RELAY NO. 1 (POINT SIDE) " TERMINAL 2 OF THE
RADIATOR FAN MOTOR " TERMINAL 1 " GROUND, THUS ACTIVATING THE ROTATION OF THE RADIATOR FAN MOTOR.
*LOW SPEED OPERATION
WHEN THE IGNITION SW IS TURNED ON AND THE A/C ACTIVATED, RADIATOR FAN RELAY NO. 1 AND RADIATOR FAN RELAY NO. 2
ARE TURNED ON, CURRENT FLOWS FROM A/C MAGNETIC CLUTCH RELAY (POINT SIDE) TO RADIATOR FAN RELAY NO. 3 (COIL
SIDE) " GROUND, AND RADIATOR FAN RELAY NO. 3 IS TURNED ON.
AS A RESULT, CURRENT FLOWS FROM CDS FAN FUSE TO TERMINAL 2 OF THE A/C CONDENSER FAN MOTOR " TERMINAL 1 "
RADIAOTR FAN RELAY NO. 2 (POINT SIDE) " RADIATOR FAN RELAY NO. 3 (POINT SIDE) " TERMINAL 2 OF THE RADIATOR FAN
MOTOR " TERMINAL 1 " GROUND, FLOWING TO EACH FAN MOTOR IN SERIES, CAUSING THE FAN TO AT LOW SPEED.
*HIGH SPEED OPERATION OF THE FAN MOTOR DUARING A/C OPERATION
WHEN THE A/C OPERATION, THE REFRIGERRANT PRESSURE BECOME HIGHER THAN OR DINARY LEVEL (APPROX. 15.58 KG/CM
2
(221.2 PSI, 1527 KPA)) THE A/C SINGLE PRESSURE SW IS TURNED OFF. AS A RESULT, RADIATOR FAN RELAY NO. 1 AND RADIATOR
FAN RELAY NO. 2 ARE TURNED OFF, AND CURRENT FLOWS FROM RDI FUSE TO RADIATOR FAN RELAY NO. 1 (POINT SIDE) "
TERMINAL 2 OF THE RADIATOR FAN MOTOR " TERMINAL 1 " GROUND, AND CURRENT FLOWS FROM CDS FAN FUSE TO
TERMINAL 2 OF THE A/C CONDENSER FAN MOTOR " TERMINAL 1 " RADIATOR FAN RELAY NO. 2 (POINT SIDE) " GROUND, AND
TO EACH FAN MOTOR IN PARALLEL, THUS CAUSING THE FAN MOTORS OPERATE HIGH SPEED.
NOTE THAT, BECAUSE THE CURRENT FLOWS IN THE SAME MENNER EVEN IF THE ENGINE COOLANT TEMPERATURE IS APPROX.
90°C (194°F) OR HIGHER, THE FAN MOTOR OPERATE AT HIGH SPEED.
A 2 A/C SINGLE PRESSURE SW
2±3 : OPEN ABOVE APPROX. 15.58 KG/CM2 (221.2 PSI, 1527 KPA)
CLOSE BELOW APPROX. 15.56 KG/CM2 (178.4 PSI, 1231 KPA)
2 1
2 1 A1R1 BLACKGRAY
12E5 A2BLACK
23
SYSTEM OUTLINE
SERVICE HINTS

25±2 (TMC Made)
26±2 (TMM Made)
ABS
(Anti±Lock Brake System)Air ConditioningAuto AntennaBack±Up LightBack Door Lock
(w/o Power Window)ChargingCombination MeterCruise ControlDoor LockElectric Tension Reducer
Engine ControlIlluminationInterior LightLight Auto Turn OffMoon RoofPower SeatPower SourcePower WindowRadiator Fan and
Condenser FanRadio and Player
36±76±2 (1MZ±FE)
7±2 (5S±FE)19±124±233±122±32±422±4 (W/G)6±7 (1MZ±FE)
7±7 (5S±FE)35±1(Lever Con±
trol SW Type)
36±1(Push Con±
trol SW Type)27±3 (W/G)28±3 (S/D,C/P)
Front Wiper and WasherHeadlight
Rear Window DefoggerRear Wiper and WasherRemote Control MirrorSRS (Supplemental
Restraint System)Shift LockStarting and IgnitionTurn Signal and Hazard
Warning LightUnlock and Seat Belt
Warning
34±3 (5S±FE)21±38±3 (for USA)
10±1 (for Canada)20±21~36±134±211±1 (S/D, C/P w/ Key
Illuminated Entry)
12±1 (W/G w/ Key
Illuminated Entry)
13±1 (S/D, C/P w/o Key
Illuminated Entry)
14±1 (W/G w/o Key
Illuminated Entry)18±418±23±1 (1MZ±FE)
4±1 (5S±FE A/T and
California M/T)
5±1 (5S±FE Ex. A/T
and California M/T)15±2
23±323±234±19±3 (S/D, C/P)
18±2 (W/G)1±2 (1MZ±FE)
2±2 (5S±FE)8±1 (W/G)
9±1 (S/D, C/P)
Taillight
24±4 (W/G)
28±1 (S/D,C/P)22±220±116±1 (S/D, C/P)
17±1 (W/G)
Stop Light
SYSTEM INDEX
21±129±1(S/D, C/P 6 Speaker)
30±1(W/G 8 Speaker)
31±1(S/D, C/P 4 Speaker)
32±2(W/G 6 Speaker)
264
Horn
Cigarette Lighter and
ClockElectrical Controlled
Transmission and
A/T Indicator
27±2 (1MZ±FE)
Electrically Controlled
Hydraulic Cooling Fan
1994 Model (Location No. 1 to 36)
OVERALL ELECTRICAL WIRING DIAGRAM

OVERALL ELECTRICAL WIRING DIAGRAM
1
234
34 CAM RY
4ACC
IG1
ST1
IG2
ST2 AM1 2
AM2
1G 91G 3
3C 16
1E 1
3A 151A 7
3EF12H 2
1C 11C7
1H 51M1
2IO17 C C
61B 6 2G 2
1 2
2 1
5IO1
BL I GB±O B± Y
W W BWB
W W
R±L R±L R± WR
R±Y R±YR±Y W±B
W±B W±B
W± B
B±O
I12
IGNITION SW 40A
AM115A
ECU± I G
I nst rument panel
brace LH Under the left
quart er pillarB7
BUCKLE SW
LH INTEGRATION
RELAY10A
GAUGE 20A
DOME
J1
JUNCTION
CONNECTOR
C9
SEAT BELT
WARNI NG LIGHT
[COMB. METER]
(
*2)
(
*1)B8
BUCKLE SW
LH FL MAIN
2. 0L
BATTERY
100A ALT1 2
4 3
1H 2
1
To Unlock Warning
SW< 19±1>
9
87 15
6 10
R±G D12
DOOR COURTES Y SW
FRONT LH
3 2H 1
5 5
1 2
5 3
4 2B 62B22E82B32E6
552B 4
5
3 2
1 EA11 2
M 5
2E
1 2
EBEB 2 EA155 55
21
3 5 1 2
M
B±W
B B±R W
W RL
W± BW±R
W± BBL B±R W±B
B±R B± R W± B W± BW± B
W± B
ENGI NE
MA I N RE LA Y
30A
RDI
FAN30A
CDS
FAN
A1
A/ C CONDE NS ER
FAN MOTOR RADIATOR
FAN RELAY
A2
A/ C SI NGL E
PRESSURE SW
RADIATOR
FAN REL AY
NO. 2
Fr ont left f ender
From A/C Magnetic
Cl ut c h Rel ay
<35±4><36±5>
RADIATOR
FAN RELAY
NO. 3 E5
WATER TEMP.
SWR1
RA DI AT OR
FAN MOTOR
Front left fender
W± B
2 1
4 5
2 1
4 3 B
2G 6
From Taillight Relay
< 15±1>
See Headlight Syst em
<8±2><10±2>2
1G±R
See Taillight System
< 16±1> < 17±1>
See Headlight
Syst em< 8±3> < 10±2>
W± B
C C
C J5
JUNCTION
CONNCT OR
(
W/G)
W± B
(
S / D, C/ P)
(
W/ G)
W±B
(
S/ D, C/ P)
(
W/G)
*1: w/PowerSeat
*2 : w/o Power Seat
(
*1)
Unlock and Seat Belt W arning
12BL±B W±B
Radiator Fan and
Condenser Fan(
5S±FE) Light Auto
Turn Off Power Source
BCFUSE BOX
1F1 0 A , B
F1 6 C (
5S±FE) (
1MZ±FE)
B 1 1A
,
C F16B (
5S±FE)
F10A (
1MZ±FE)
F10FUSE BOX
1 1