turn signal TOYOTA CAMRY 1994 XV10 / 4.G Wiring Diagrams Workshop Manual

METER, ANALOG
Current flow activates a magnetic
coil which causes a needle to
move, thereby providing a relative
display against a background
calibration. LED (LIGHT EMITTING DIODE)
Upon current flow, these diodes
emit light without producing the
heat of a comparable light. IGNITION COIL
Converts low±voltage DC current
into high±voltage ignition current
for firing the spark plugs. 1. SINGLE
FILAMENT
GROUND
The point at which wiring attaches
to the Body, thereby providing a
return path for an electrical circuit;
without a ground, current cannot
flow.Current flow causes a headlight
filament to heat up and emit light.
A headlight may have either a
single (1) filament or a double (2)
filament. BATTERY
Stores chemical energy and
converts it into electrical energy.
Provides DC current for the auto's
various electrical circuits.
CAPACITOR (Condenser)
A small holding unit for temporary
storage of electrical voltage.
CIRCUIT BREAKER
Basically a reusable fuse, a circuit
breaker will heat and open if too
much current flows through it. Some
units automatically reset when cool,
others must be manually reset.
DIODE
A semiconductor which allows
current flow in only one direction.
DIODE, ZENER
A diode which allows current flow
in one direction but blocks reverse
flow only up to a specific voltage.
Above that potential, it passes the
excess voltage. This acts as a
simple voltage regulator.
FUSE
A thin metal strip which burns
through when too much current
flows through it, thereby stopping
current flow and protecting a
circuit from damage.
FUSIBLE LINK
A heavy±gauge wire placed in
high amperage circuits which
burns through on overloads,
thereby protecting the circuit.
The numbers indicate the cross±
section surface area of the wires.HORN
An electric device which sounds a
loud audible signal.
LIGHT
Current flow through a filament
causes the filament to heat up
and emit light.
METER, DIGITAL
Current flow activates one or
many LED's, LCD's, or fluorescent
displays, which provide a relative
or digital display.
MOTOR
A power unit which converts
electrical energy into mechanical
energy, especially rotary motion. CIGARETTE LIGHTER
An electric resistance heating
element.
DISTRIBUTOR, IIA
Channels high±voltage current
from the ignition coil to the
individual spark plugs.2. DOUBLE
FILAMENT HEADLIGHTS
FUEL
(for High Current Fuse or
Fusible Link.)
(for Medium Current Fuse)
M
16
GLOSSARY OF TERMS AND SYMBOLS

17
1. NORMALLY
OPENOpens and
closes circuits,
thereby
stopping (1) or
allowing (2)
current flow.
RESISTOR
An electrical component with a
fixed resistance, placed in a circuit
to reduce voltage to a specific
value.
RESISTOR, TAPPED
A resistor which supplies two or
more different non adjustable
resistance values.
SENSOR (Thermistor)
A resistor which varies its
resistance with temperature.
SHORT PIN
Used to provide an unbroken
connection within a junction block.
SOLENOID
An electromagnetic coil which
forms a magnetic field when
current flows, to move a plunger,
etc.SWITCH, DOUBLE THROW
A switch which continuously
passes current through one set
of contacts or the other.
SWITCH,
IGNITION
A key operated switch with
several positions which allows
various circuits, particularly the
primary ignition circuit, to
become operational.
Wires are always
drawn as straight lines
on wiring diagrams.
Crossed wires (1)
without a black dot at
the junction are not
joined; crossed wires
(2) with a black dot or
octagonal (
) mark at
the junction are spliced
(joined) connections. RELAY, DOUBLE THROW
A relay which passes current
through one set of contacts or the
other.
SENSOR, ANALOG SPEED
Uses magnetic impulses to open
and close a switch to create a
signal for activation of other
components.TRANSISTOR
A solidstate device typically used
as an electronic relay; stops or
passes current depending on the
voltage applied at ªbase.º SWITCH, WIPER PARK
Automatically returns wipers to
the stop position when the wiper
switch is turned off. SWITCH, MANUAL SPEAKER
An electromechanical device
which creates sound waves from
current flow.
2. NORMALLY
CLOSED
RESISTOR, VARIABLE or
RHEOSTAT
A controllable resistor with a
variable rate of resistance.
Also called a potentiometer or
rheostat. 2. NORMALLY
OPEN RELAY
1. NORMALLY
CLOSEDBasically, an electrically
operated switch which may
be normally closed (1) or
open (2).
Current flow through a
small coil creates a
magnetic field which either
opens or closes an
attached switch.
(2) SPLICED WIRES
(1) NOT
CONNECTED

28
ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
[1MZ±FE]
A 2 A/C Triple Pressure SW (A/C Dual and Single Pressure F 1 Front Airbag Sensor LH
SW) F 2 Front Airbag Sensor RH
A 3 A/C Magnetic Clutch and Lock Sensor F 3 Front Clearance Light LH
A 4 ABS Actuator F 4 Front Clearance Light RH
A 5 ABS Actuator F 5 Front Side Marker LH
A 6 ABS Relay F 6 Front Side Marker RH
A 7 ABS Relay F 7 Front Turn Signal Light LH
A 8 ABS Speed Sensor Front LH F 8 Front Turn Signal Light RH
A 9 ABS Speed Sensor Front RH F 9 Front Wiper Motor
F 10 Fuse Box
B 2 Brake Fluid Level SW F 16 Fuse Box
F 18 Fuse Box
C 2 Cruise Control Actuator
C 17 Camshaft Position Sensor G 1 Generator (Alternator)
C 18 Crankshaft Position Sensor G 2 Generator (Alternator)
D 1 Data Link Connector 1 (Check Connector) H 1 Headlight Hi LH
D 2 Distributor H 2 Headlight Hi RH
H 3 Headlight Lo LH
E 1 EGR Gas Temp. Sensor H 4 Headlight Lo RH
E 2 Electronic Controlled Transmission Solenoid H 5 Horn LH
E 4 Engine Coolant Temp. Sensor (EFI Water Temp. H 6 Horn RH
Sensor) H 11 Heated Oxygen Sensor (Bank 1 Sensor 1)
E 5 Engine Coolant Temp. Sensor (Water Temp. Sensor) H 12 Heated Oxygen Sensor (Bank 2 Sensor 1)
(for Cooling Fan)

30
ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
[5S±FE]
A 1 A/C Condenser Fan Motor E 1 EGR Gas Temp. Sensor
A 2 A/C Triple Pressure SW (A/C Dual and Single Pressure E 2 Electronic Controlled Transmission Solenoid
SW) E 3 Electronic Controlled Transmission Solenoid
A 3 A/C Magnetic Clutch and Lock Sensor E 4 Engine Coolant Temp. Sensor (EFI Water Temp.
A 4 ABS Actuator Sensor)
A 5 ABS Actuator E 5 Water Temp. SW (for Cooling Fan)
A 6 ABS Relay
A 7 ABS Relay F 1 Front Airbag Sensor LH
A 8 ABS Speed Sensor Front LH F 2 Front Airbag Sensor RH
A 9 ABS Speed Sensor Front RH F 3 Front Clearance Light LH
F 4 Front Clearance Light RH
B 1 Back±Up Light SW (M/T) F 5 Front Side Marker LH
B 2 Brake Fluid Level SW F 6 Front Side Marker RH
F 7 Front Turn Signal Light LH
C 2 Cruise Control Actuator F 8 Front Turn Signal Light RH
F 9 Front Wiper Motor
D 1 Data Link Connector 1 (Check Connector) F 10 Fuse Box
D 2 Distributor F 16 Fuse Box
F 17 Fuse Box
F 18 Fuse Box
G 1 Generator (Alternator)
G 2 Generator (Alternator)

55
192 17711 4
11 8
Cruise Control Actuator
C2 C5 C10 C11 C13 D8C12 C3 C4 C6 C8 C9 C14 C16 D1 D3 D4 D6 D7
Center Airbag Sensor Assembly
Cigarette Lighter
Cigarette Lighter Illumination
Clock
Combination Meter
(Turn Signal Indicator Light)Combination Meter
(Cruise Control Indicator Light)
Combination Meter
Combination Meter
(Meter Illmination)
Combination Meter
(Open Door Warning Light)
Combination Meter
(Seat Belt Warning Light)
Combination Meter
(Charge Warning Light)
Combination Meter
(High Beam Indicator Light)
Combination Meter
(Rear Light Warning Light)
Combination Meter
Combination Meter
(SRS Warning Light)
Combination Meter
(A/T Indicator Light)
Combination SW (Horn SW)
Combination SW
(Turn Signal SW)
Combination SW
(Light Control SW)
Combination SW
Front Wiper and Washer SW)
Cooling Fan ECU (1MZ±FE)
Cruise Control ECU
Data Link Connector 1
(Check Connector)
Data Link Connector 2
(TDCL (Toyota Diagnostic
Communication Link))
Daytime Running Light Relay
(Main) (CANADA)
Diode (for Idle±Up)
Diode (for Courtesy) (W/G) Door Lock Control Relay
18912618968
72192236210
21476 130
134
138
140 126120
124
144
148236126
198
204104
11 2
144244 80
90
98
214 90
192
214106
23680
90
98130
134
138
140156
140 104
106
D9 C717080
90
98177 17311 4
11 8106
126
148184
186192 98
204134
140
Diode (for Courtesy) Combination Meter
(Malfunction Indicator Light) Combination Meter
(ABS Warning Light) Clutch Start SW (M/T)
(4): R/B No. 4 (See page 20)(5): R/B No. 5 (See page 19)(6)R/B No. 6 (See Page )
2526 26

57
E10 80
98
204 80
90
98
236 184
F376 144
148126
246252
Engine Control Module (Engine
and Electronic Controlled
Transmission ECU)
High Mount Stop Light
Heated Oxygen Sensor (Bank 2
Sensor 1) (1MZ±FE)
Idle Air Control Valve (ISC Valve)
Igniter
Ignition Coil
Injector No. 1
F4 F5 F6 F7 F8 F9 F15 G2 G3 G4 H1 H2 H3 H4 H5 H6 H7 H8 H9 H10 H11 H12 I1 I2 I3 I4 90
198144
148144
148144
14811 4
11 811 4
11 8126 126 104 106 104 106 104 106 104 106 173 17311 4
11 8
12680120
12480 8080
90
9868
8072
98
23672 80
Heated Oxygen Sensor (Bank 1
Sensor 1) (1MZ±FE) Heated Oxygen Sensor (Bank 1
Sensor 2) Air Vent Mode Control SW (for
Lever Control SW Type) Heater Control SW (for Push
Control SW Type) Hazard SW Horn RH
Horn LH Front Clearance Light LH
Front Clearance Light RH
Front Side Marker LH
Front Side Marker RH
Front turn Signal Light LH
Front turn Signal Light RH
Front Wiper Motor
Fuel Pump and Sender
Generator (Alternator)
Glove Box Light
Glove Box Light SW
Headlight Hi LH (USA)
Headlight Hi LH (CANADA)
Headlight Hi RH (USA)
Headlight Hi RH (CANADA)
Headlight Lo LH (USA)
Headlight Lo LH (CANADA)
Headlight Lo RH (USA)
Headlight Lo RH (CANADA)
(4): R/B No. 4 (See page 20)(5): R/B No. 5 (See page 19)(6)R/B No. 6 (See Page )
2526 26

60
POWER SOURCE (Current Flow Chart)
*Page Nos. of
Related Systems
Parts
Code or
Location
CB or Fuse
Location
156
* These are the page numbers of the first page on which the related system is shown.
The part indicated is located somewhere in the system, not necessarily on the page indicated here.


P13 P14 P15 P16 R1 R2 R3 R5 R6 R7 R8 R9156 156126
222
224
228
234126
190154120
124
Power Window Motor Front LH
Power Window Motor Front RH
Power Window Motor Rear LH
(EX. C/P)
Radiator Fan Motor (5S±FE)
Radio and Player (w/ CD Player)
Radio and Player (w/o CD Player)
Rear Window Defogger SW
Remote Control mirror SW
Rheostat
Stop Light LH
[Rear Comb. Light LH]
Taillight LH
[Rear Comb. Light LH]
Rear Turn Signal Light LH
[Rear Comb. Light LH]
Stop Light LH
[Rear Comb. Light LH]
40A AM1
15A CIG/RADIO
40A DEFOG
15A ECU±1G
10A GAUGE
7.5A IGN
10A MIR±HTR
30A POWER
7.5A SRS
15A STOP
15A TAIL
7.5A TURN
20A WIPER
30A AM2
7.5A ALT±S
30A CDS FAN
20A DOME
15A ECU±B
15A EFI
10A HAZ
15A HEAD (LWR±LH)
15A HEAD (LWR±RH)
15A HEAD (UPR±LH)
15A HEAD (UPR±RH)
15A HEAD LH
15A HEAD RH
10A HORN
40A MAIN
7.5A OBD
10A STARTER
10A A/C
40A HEATER
7.5A DRL
100A ALT
60A ABSR10 R11 R16 R17
Power Window Motor Rear RH
(EX. C/P)
Taillight LH
[Rear Comb. Light LH]
Back±up Light LH
[Rear Comb. Light LH]
Stop Light RH
[Rear Comb. Light RH]
Taillight RH
[Rear Comb. Light RH]
Rear Turn Signal Light RH
[Rear Comb. Light RH]
Taillight RH
[Rear Comb. Light RH]
Stop Light RH
[Rear Comb. Light RH]
Back±up Light RH
[Rear Comb. Light RH]
Rear Window Defogger (+)
(EX. W/G)
Rear Window Defogger (±)
(EX. W/G)
Rear Window Defogger (±)
(W/G)
156 242 126 126144
14811 4
148120
124144
148152120
124144
14811 4
11 8144
148120
124152 190 190 190
[LOCATION](1)
(7): J/B No. 1 (See page 20)
: R/B No. 7 (See page )(2)
(8): J/B No. 2 (See page 19)
: Fuse Box (F10, F17 See
on page )(3): R/B No. 1 (See page 23)
2022
25
27
28 29

62
POWER SOURCE (Current Flow Chart)
*Page Nos. of
Related Systems
Parts
Code or
Location
CB or Fuse
Location
* These are the page numbers of the first page on which the related system is shown.
The part indicated is located somewhere in the system, not necessarily on the page indicated here.


106
Horn Relay
Headlight Relay (Point Side)
Radiator Fan Relay (Point Side)
Turn Signal Flasher
Heater Relay (Point Side)
Radiator Fan Relay No. 2
(Coil Side)
A/C Magnetic Clutch Relay
(Coil Side)
Daytime Running Light Relay No. 3
(Coil Side)
40A AM1
15A CIG/RADIO
40A DEFOG
15A ECU±1G
10A GAUGE
7.5A IGN
10A MIR±HTR
30A POWER
7.5A SRS
15A STOP
15A TAIL
7.5A TURN
20A WIPER
30A AM2
7.5A ALT±S
30A CDS FAN
20A DOME
15A ECU±B
15A EFI
10A HAZ
15A HEAD (LWR±LH)
15A HEAD (LWR±RH)
15A HEAD (UPR±LH)
15A HEAD (UPR±RH)
15A HEAD LH
15A HEAD RH
10A HORN
40A MAIN
7.5A OBD
10A STARTER
10A A/C
40A HEATER
7.5A DRL
100A ALT
60A ABS
Radiator Fan Relay (Coil Side)
Heater Relay (Coil Side)
Radiator Fan Relay No. 2
(Point Side)
Radiator Fan Relay No. 3
(Point Side)
A/C Magnetic Clutch Relay
(Point Side)
Circuit Opening Relay (Coil Side)
Circuit Opening Relay (Coil Side)
Daytime Running Light Relay No. 4
(Coil Side)
106 173 106 242 24211 4
11 8246 246 242 242 242 246 24680
90
9880
90
98
[LOCATION](1)
(4): J/B No. 1 (See page 20)
: R/B No. 4 (See page )(2)
(5): J/B No. 2 (See page 19)
: R/B No. 5 (See page )(3)
(6): R/B No. 1 (See page 23)
: R/B No. 6 (See page )
(7): R/B No. 7 (See page 20)(8): Fuse Box (F10, F17 See
on page 19) 20 2225
25
28 2926 26
27

78
ENGINE CONTROL (1MZ±FE)
THIS SYSTEM UTILIZES AN ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU) AND
MAINTAINS OVERALL CONTROL OF THE ENGINE, TRANSMISSION AND SO ON. AN OUTLINE OF THE ENGINE CONTROL IS
EXPLAINED HERE.
1. INPUT SIGNALS
(1) ENGINE COOLANT TEMP. (WATER TEMP.) SIGNAL CIRCUIT
THE ENGINE COOLANT TEMP. SENSOR (WATER TEMP. SENSOR) DETECTS THE ENGINE COOLANT TEMP. AND HAS A
BUILT±IN THERMISTOR WITH A RESISTANCE WHICH VARIES ACCORDING TO THE WATER TEMP. IS INPUT INTO TERMINAL
THW OF ENGINE CONTROL MODULE (ECU) AS A CONTROL SIGNAL.
(2) INTAKE AIR TEMP. SIGNAL CIRCUIT
THE INTAKE AIR TEMP. SENSOR IS INSTALLED IN THE MASS AIR FLOW (AIR FLOW METER) AND DETECTS THE INTAKE AIR
TEMP., WHICH IS INPUT AS A CONTROL SIGNAL TO TERMINAL THA OF ENGINE CONTROL MODULE (ECU).
(3) OXYGEN SENSOR SIGNAL SYSTEM
THE OXYGEN DENSITY IN THE EXHAUST GASES IS DETECTED AND INPUT AS A CONTROL SIGNAL TO TERMINAL OXL, OXR
AND OXS OF THE ENGINE CONTROL MODULE (ECU). TO MAINTAIN STABLE DETECTION PERFORMANCE BY THE OXYGEN
SENSOR, A HEATER IS USED FOR WARMING THE SENSOR. THE HEATER IS ALSO CONTROLLED BY THE ENGINE CONTROL
MODULE (ECU) (HTL, HTR AND HTS).
(4) RPM SIGNAL SYSTEM
CAMSHAFT POSITION AND CRANKSHAFT POSITION ARE DETECTED BY THE CAMSHAFT POSITION SENSOR AND
CRANKSHAFT POSITION SENSOR. CRANKSHAFT POSITION IS INPUT AS A CONTROL SIGNAL TO TERMINAL G22+ OF THE
ENGINE CONTROL MODULE (ECU), AND ENGINE RPM IS INPUT TO TERMINAL NE+.
(5) THROTTLE SIGNAL CIRCUIT
THE THROTTLE POSITION SENSOR DETECTS THE THROTTLE VALVE OPENING ANGLE AS A CONTROL SIGNAL, WHICH IS
INPUT INTO TERMINAL VTA OF THE ENGINE CONTROL MODULE (ECU). WHEN THE VALVE IS COMPLETELY CLOSED, THE
CONTROL SIGNAL IS INPUT INTO TERMINAL IDL.
(6) VEHICLE SPEED SIGNAL SYSTEM
THE VEHICLE SPEED SENSOR (SPEED SENSOR), INSTALLED INSIDE THE COMBINATION METER, DETECTS THE VEHICLE
SPEED AND INPUTS A CONTROL SIGNAL TO TERMINAL SP1 OF THE ENGINE CONTROL MODULE (ECU).
(7) PARK/NEUTRAL POSITION SW (NEUTRAL START SW) SIGNAL SYSTEM
THE PARK/NEUTRAL POSITION SW (NEUTRAL START SW) DETECTS WHETHER THE SHIFT POSITION IS IN NEUTRAL OR
PARKING OR NOT, AND INPUTS A CONTROL SIGNAL TO TERMINAL NSW OF THE ENGINE CONTROL MODULE (ECU).
(8) A/C SW SIGNAL SYSTEM
THE A/C AMPLIFIER INPUTS THE A/C OPERATIONS TO TEMRINAL A/C OF THE ENGINE CONTROL MODULE (ECU) AS A
CONTROL SIGNAL.
(9) BATTERY SIGNAL CIRCUIT
VOLTAGE IS CONSTANTLY APPLIED TO TERMINAL BATT OF THE ENGINE CONTROL MODULE (ECU). WHEN THE IGNITION SW
TURNED ON, VOLTAGE FOR ENGINE CONTROL MODULE (ECU) START±UP POWER SUPPLY IS APPLIED TO TERMINALS +B
AND +B1 OF ENGINE CONTROL MODULE (ECU) VIA EFI MAIN RELAY.
(10) INTAKE AIR VOLUME SIGNAL CIRCUIT
INTAKE AIR VOLUME IS DETECTED BY THE MASS AIR FLOW (AIR FLOW METER) AND THE SIGNAL IS INPUT TO TERMINAL VG
OF THE ENGINE CONTROL MODULE (ECU). AS A CONTROL SIGNAL.
(11) STA SIGNAL CIRCUIT
TO CONFIRM WHETHER THE ENGINE IS CRANKING, THE VOLTAGE APPLIED TO THE STARTER MOTOR DURING CRANKING IS
DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL STA OF THE ENGINE CONTROL MODULE (ECU) AS A CONTROL
SIGNAL.
(12) ENGINE KNOCK SIGNAL CIRCUIT
ENGINE KNOCKING IS DETECTED BY THE KNOCK SENSOR NO. 1 AND NO. 2 AND THE SIGNALS ARE INPUT INTO TERMINALS
KNKR AND KNKL AS A CONTROL SIGNAL.
SYSTEM OUTLINE

79
2. CONTROL SYSTEM
*SFI (SEQUENTIAL MULTIPORT FUEL INJECTION) (EFI (ELECTRONIC FUEL INJECTION) SYSTEM
THE EFI SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT FROM EACH SENSOR (INPUT SIGNALS
FROM (1) TO (12) ETC.). THE BEST FUEL INJECTION VOLUME IS DECIDED BASED ON THIS DATA AND THE PROGRAM MEMORIZED
BY THE ENGINE CONTROL MODULE (ECU), AND THE CONTROL SIGNAL IS OUTPUT TO TERMINALS #10, #20, #30, #40, #50 AND #60
OF THE ENGINE CONTROL MODULE (ECU) TO OPERATE THE INJECTOR (INJECT THE FUEL). THE EFI SYSTEM PRODUCES
CONTROL OF FUEL INJECTION OPERATION BY THE ENGINE CONTROL MODULE (ECU) IN RESPONSE TO THE DRIVING
CONDITIONS.
*ESA (ELECTRONIC SPARK ADVANCE) SYSTEM
THE ESA SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT TO THE ENGINE CONTROL MODULE (ECU)
FROM EACH SENSOR (INPUT SIGNALS FROM (1), (3), (4) TO (12) ETC.). THE BEST IGNITION TIMING IS DECIDED ACCORDING TO
THIS DATA AND THE MEMORIZED DATA IN THE ENGINE CONTROL MODULE (ECU) AND THE CONTROL SIGNAL IS OUTPUTS TO
TERMINALS IGT1, IGT2, IGT3, IGT4, IGT5 AND IGT6. THIS SIGNAL CONTROLS THE IGNITER TO PROVIDE THE BEST IGNITION
TIMING FOR THE DRIVING CONDITIONS.
*HEATED OXYGEN SENSOR (OXYGEN SENSOR) HEATER CONTROL SYSTEM
THE OXYGEN SENSOR HEATER CONTROL SYSTEM TURNS THE HEATER ON WHEN THE INTAKE AIR VOLUME IS LOW (TEMP. OF
EXHAUST EMISSIONS IS LOW), AND WARMS UP THE OXYGEN SENSOR (NO. 1 AND NO. 2) TO IMPROVE DETECTION
PERFORMANCE OF THE SENSOR.
THE ENGINE CONTROL MODULE (ECU) EVALUATES THE SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (9) TO (10)
ETC.), AND OUTPUT CURRENT TO TERMINALS HTL, HTR AND HTS AND CONTROL THE HEATER.
*IAC (IDLE AIR CONTROL (ISC)) SYSTEM
THE IAC (ISC) SYSTEM (ROTARY SOLENOID TYPE) INCREASES THE RPM AND PROVIDES IDLE STABILITY FOR FAST IDLE±UP
WHEN THE ENGINE IS COLD, AND WHEN THE IDLE SPEED HAS DROPPED DUE TO ELECTRICAL LOAD AND SO ON, THE ENGINE
CONTROL MODULE (ECU) EVALUATES THE SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (5), (8), (9) ETC.),
OUTPUTS CURRENT TO TERMINALS RSO AND RSC TO CONTROL IDLE AIR CONTROL VALVE.
*EGR CONTROL SYSTEM
THE EGR CONTROL SYSTEM DETECTS THE SIGNAL FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (9), (10), ETC)., AND
OUTPUTS CURRENT TO TERMINAL EGR TO CONTROL THE EGR VALVE.
*ACIS (ACOUSTIC CONTROL INDUCTION SYSTEM)
ACIS INCLUDES A VALVE IN THE BULKHEAD SEPARATING THE SURGE TANK INTO TWO PARTS. THIS VALVE IS OPENED AND
CLOSED IN ACCORDANCE WITH THE DRIVING CONDITIONS TO CONTROL THE INTAKE MANIFOLD LENGTH IN TWO STAGES FOR
INCREASED ENGINE OUTPUT IN ALL RANGES FROM LOW TO HIGH SPEEDS.
THE ENGINE CONTROL MODULE (ECU) JUDGES THE ENGINE SPEED BY THE SIGNALS ((4), (5)) FROM EACH SENSOR AND
OUTPUTS SIGNALS TO THE TERMINAL ACIS TO CONTROL THE VSV (FOR OPENING AND CLOSING THE INTAKE CONTROL VALVE)
3. DIAGNOSIS SYSTEM
WITH THE DIAGNOSIS SYSTEM, WHEN THERE IS A MALFUNCTION IN THE ENGINE CONTROL MODULE (ECU) SIGNAL SYSTEM, THE
MALFUNCTIONING SYSTEM IS RECORDED IN THE MEMORY.
4. FAIL±SAFE SYSTEM
WHEN A MALFUNCTION HAS OCCURRED IN ANY SYSTEM, IF THERE IS A POSSIBILITY OF ENGINE TROUBLE BEING CAUSED BY
CONTINUED CONTROL BASED ON THE SIGNALS FROM THAT SYSTEM, THE FAIL±SAFE SYSTEM EITHER CONTROLS THE SYSTEM
BY USING DATA (STANDARD VALUES) RECORDED IN THE ENGINE CONTROL MODULE (ECU) MEMORY OR ELSE STOPS THE
ENGINE.