torque specifications TOYOTA CAMRY 1999 Service Manual PDF

SS04X±03
SS±10
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
FRONT AXLE
Hub nut1031,05076
Steering knuckle x Shock absorber2112,150156
Steering knuckle x Brake caliper1071,09079
Steering knuckle x Tie rod end4950036
Axle hub x Drive shaft2943,000217
Lower ball joint x Lower suspension arm1271,30094
Lower ball joint x Steering knuckle1231,25090
ABS speed sensor set bolt8.08271 in.´lbf
Tie lod end lock nut7475054
FRONT DRIVE SHAFT
Drive shaft center bearing lock bolt3233024
FRONT SUSPENSION
Suspension support x Body8082059
Suspension support x Piston rod4950036
Flexible hose and ABS speed sensor wire harness x Shock absorber2930022
Lower suspension arm set bolt2062,100152
Stabilizer bar link set bolt3940029
REAR AXLE
Hub nut1031,05076
Axle hub set bolt8082059
Shock absorber x Rear axle carrier New nut
Reused nut (Apply engine oil to the threads.)255
1962,600
2,000188
145
No. 1, No. 2 lower suspension arm x Rear axle carrier1811,850134
Strut rod x Rear axle carrier11 31,15083
Flexible hose x Shock absorber2930022
ABS speed sensor set bolt8.08271 in.´lbf
REAR SUSPENSION
ABS speed sensor wire harness x Shock absorber5.45548 in.´lbf
Rear seat outer belt lower side set bolt4243031
Suspension support x Body3940029
Suspension support x Piston rod4950036
Parking brake cable set bolt5.45548 in.´lbf
No. 2 lower suspension arm lock nut5657041
No. 1, No. 2 lower suspension arm x Suspension member1811,850134
Strut rod x Body11 31,15083
Stabilizer bar bracket x Suspension member1919514
Stabilizer bar link set nut3940029

SS13F±01
SS±12
± SERVICE SPECIFICATIONSBODY
70 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
REAR BUMPER±±±
Rear bumper cover x Body4.95143 in.´lbf
Rear bumper reinforcement x Body3435025
Rear bumper side retainer x Body4.95143 in.´lbf
LUGGAGE COMPARTMENT DOOR AND HINGE±±±
Door lock striker x Body5.45549 in.´lbf
Door lock x Door panel5.45549 in.´lbf
Luggage compartment door hinge x Door panel7.88069 in.´lbf
REAR SEAT±±±
Rear seatback x Body1818513
SEAT BELT±±±
Front seat belt±±±
Retractor x Body Upper:7.88069 in.´lbf
Lower:4142030
Inner belt x Seat4142030
Shoulder anchor x Body4142030
Floor anchor x Body4142030
Rear seat belt±±±
Retractor x Body4142030
Floor anchor x Body4142030
RH center belt x Body4142030
LH center belt x Body4142030

POWER SEAT MOTOR CABLE REPAIR TIP ± BO017-01 Revised May 25, 2001
Page 2 of 2
1. Remove the seat assembly from the
vehicle.
Turn the seat over and detach motors
from the mounting brackets.
NOTE:
The lower seat cushion must be
removed from the seat frame to access
the motor mounting screws on some
models.
2. Remove the drive cable from the motor gear boxes. Slide a shrink wrap tube
(3/4º diameter x 1.75º, 3M P/N 36596) on each end of the flex shaft, as shown in
the illustration.
The Camry and Sienna will require six (6) shrink tubes.
The Solara will require only one (1) shrink tube.
Camry/Sienna Solara
Front
3. Attach the drive cables to the motors and reinstall motors to the motor mounts.
4. Position each shrink wrap tube so that it overlaps the drive cable housing and motor
housing or gear box housing, as necessary.
5. Using a heat gun, apply heat to the
shrink tubes in a direction from the
center of the drive cable toward the
gear box or motor housing. Be sure to
apply just enough heat to shrink the
tubing.
6. Reinstall the seat cushion to the seat
frame. Tighten the mounting screws to
torque specifications listed in the BO
section of the Repair Manual.
7. Reinstall the seat assembly to the
floor of the vehicle. Assure all
connectors are secure and the power
seat adjustments properly function.
Torque: 37 Nm, 380 kgfcm, 27 ftlbs
Repair
Procedure
Heat Gun
Shrink Tube

SEAT COVER LOOSENESS ± BO020±99 December 17, 1999
Page 3 of 3
6. Reassemble the seat cushion.
7. Bend the locking tabs over the
cushion.
8. After reinstallation of the seat and
manual seat adjuster handle
(if removed), check the seat cushion
retention and seat operation
(sit on seat and push cushion down).
9. Tighten the seat mounting screws to
the torque specifications in the Repair
Manual.Repair
Procedure
(Continued)
Locking Tabs

TOYOTA MOTOR SALES U.S.A., INC.
The following bolt mark and class identification information is currently not included in the Standard
Bolt Torque Specifications found in the Introduction section of each Toyota Repair Manual.
BOLT MARK CLASS
(Hexagon flange bolt or 4 Protruding Lines 9T
Hexagon bolt with washer)
(Hexagon flange bolt or 5 Protruding Lines 10T
Hexagon bolt with washer)
(Hexagon flange bolt or 6 Protruding Lines 11T
Hexagon bolt with washer)
SPECIFIED TORQUE FOR STANDARD BOLTS
SPECIFIED TORQUE
CLASS DIAMETER PITCH HEXAGON HEAD BOLT HEXAGON FLANGE BOLT
mm mm Nm kgfcm ftlbf Nm kgfcm ftlbf
8 1.25 34 340 25 37 380 27
9T 10 1.25 70 710 51 78 790 57
12 1.25 125 1300 94 140 1450 105
8 1.25 38 390 28 42 430 31
10T 10 1.25 78 800 58 88 890 64
12 1.25 140 1450 105 155 1600 116
8 1.25 42 430 31 47 480 35
11T 10 1.25 87 890 64 97 990 72
12 1.25 155 1600 116 175 1800 130
STANDARD BOLT TORQUE SPECIFICATIONSPage 1 of 1
PRODUCT GENERAL
INFORMATION
PG95-006
JULY 21, 1995
ALL MODELS