coolant TOYOTA CAMRY 1999 Service Manual PDF

DI1JT±03
D00032
E9E8E7
ECM Terminals DI±22
± DIAGNOSTICSENGINE (5S±FE)
257 Author: Date:
TERMINALS OF ECM
Without engine immobiliser system
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
BATT (E7 ± 1) ± E1 (E9 ± 14)B ± Y e BRAlways9 ~ 14
+ B (E7 ± 12) ± E1 (E9 ± 14)B ± Y e BRIG switch ON9 ~ 14
VC (E8 ± 1) ± E2 (E8 ± 9)Ye BRIG switch ON4.5 ~ 5.5
VTA (E8 11) E2 (E8 9)LGBR
IG switch ON
Throttle valve fully closed0.3 ~ 1.0
VTA (E8 ± 11) ± E2 (E8 ± 9)LG e BRIG switch ON
Throttle valve fully open3.2 ~ 4.9
PIM (E8 2) E2 (E8 9)BYBR
IG switch ON3.3 ~ 3.9
PIM (E8 ± 2) ± E2 (E8 ± 9)B ± Y e BRApply vacuum 26.7 kPa (200 mmHg, 7.9 in.Hg)2.5 ~ 3.1
THA (E8 ± 3) ± E2 (E8 ± 9)Y ± B e BRIdling, Intake air temp. 20°C (68° F)0.5 ~ 3.4
THW (E8 ± 4) ± E2 (E8 ± 9)G ± B e BRIdling, Engine coolant temp. 80°C (176°F) 0.2 ~ 1.0
STA (E7 11) E1 (E9 14)*1 GR e BRCranking6.0 or moreSTA (E7 ± 11) ± E1 (E9 ± 14) *2 B ± O e BRCranking6.0 or more
IG switch ON9 ~ 14
#10 (E9 ± 12) ± E01 (E9 ± 13) L e BRIdlingPulse generation
(See page DI±89)
IG switch ON9 ~ 14
#20 (E9 ± 11) ± E01 (E9 ± 13)R e BRIdlingPulse generation
(See page DI±89)
IG switch ON9 ~ 14
#30 (E9 ± 25) ± E01 (E9 ± 13)Y e BRIdlingPulse generation
(See page DI±89)
IG switch ON9 ~ 14
#40 (E9 ± 24) ± E01 (E9 ± 13)W e BRIdlingPulse generation
(See page DI±89)
IGT1 (E9 ± 20) ± E1 (E9 ± 14)B e BRIdlingPulse generation
(See page DI±163)
IGT2 (E9 ± 19) ± E1 (E9 ± 14)Y ± R e BRIdlingPulse generation
(See page DI±163)
IG switch ON, Disconnect ignition coil connector4.5 ~ 5.5
IGF (E9 ± 3) ± E1 (E9 ± 14)W ± R e BRIdlingPulse generation
(See page DI±163)
*1: TMC made
*2: TMMK made

A02958
E7ECM Terminals
E9E8E10
11
19
1412 10 9 8
7652
43
18 21 22
20
16151
13
17 11 14
109
87 652 4
3
21 2220
16 15 131
12 11 1 09
652
43 1 12
7 8
19
14
109 8
7652
43
18
23 2416
151
17
11 12 13 25
26
± DIAGNOSTICSENGINE (5S±FE)
DI±25
260 Author: Date:
With engine immobiliser system
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
BATT (E7 ± 2) ± E1 (E9 ± 24)B ± Y e BRAlways9 ~ 14
+ B (E7 ± 12) ± E1 (E9 ± 24)B ± Y e BRIG switch ON9 ~ 14
VC (E8 ± 1) ± E2 (E8 ± 9)Ye BRIG switch ON4.5 ~ 5.5
VTA (E8 10) E2 (E8 9)LGBR
IG switch ON
Throttle valve fully closed0.3 ~ 1.0
VTA (E8 ± 10) ± E2 (E8 ± 9)LG e BRIG switch ON
Throttle valve fully open3.2 ~ 4.9
PIM (E8 2) E2 (E8 9)BYBR
IG switch ON3.3 ~ 3.9
PIM (E8 ± 2) ± E2 (E8 ± 9)B ± Y e BRApply vacuum 26.7 kPa (200 mmHg, 7.9 in.Hg)2.5 ~ 3.1
THA (E8 ± 3) ± E2 (E8 ± 9)Y ± B e BRIdling, Intake air temp. 20°C (68° F)0.5 ~ 3.4
THW (E8 ± 4) ± E2 (E8 ± 9)G ± B e BRIdling, Engine coolant temp. 80°C (176°F) 0.2 ~ 1.0
STA (E7 11) E1 (E9 24)*1 GR e BRCranking6.0 or moreSTA (E7 ± 11) ± E1 (E9 ± 24) *2 B ± O e BRCranking6.0 or more
#10 (E9 12)IG switch ON9 ~ 14#10 (E9 ± 12)
± E01 (E9 ± 13) L e BRIdlingPulse generation
(See page DI±89)
#20 (E9 11)IG switch ON9 ~ 14#20 (E9 ± 11)
± E01 (E9 ± 13)R e BRIdlingPulse generation
(See page DI±89)
#30 (E9 10)IG switch ON9 ~ 14#30 (E9 ± 10)
± E01 (E9 ± 13)Y e BRIdlingPulse generation
(See page DI±89)
IG switch ON9 ~ 14
#40 (E9 ± 9) ± E01 (E9 ± 13)W e BRIdlingPulse generation
(See page DI±89)
IGT1 (E9 ± 23)
± E1 (E9 ± 24)B e BRIdlingPulse generation
(See page DI±163)
IGT2 (E9 ± 22)
± E1 (E9 ± 24)Y ± R e BRIdlingPulse generation
(See page DI±163)
IG switch ON, Disconnect ignition coil connector4.5 ~ 5.5
IGF (E9 ± 17) ± E1 (E9 ± 24)W ± R e BRIdlingPulse generation
(See page DI±163)
*1: TMC made
*2: TMMK made

A00309
ECM Manifold Absolute
Pressure Sensor
1PIMVC
E2 Y
B±Y
BRE8
E8
E8 3
25 V
E1 1
2
9 DI±30
± DIAGNOSTICSENGINE (5S±FE)
265 Author: Date:
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P0105 (Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction), P0106 (Manifold
Absolute Pressure /Barometric Pressure Circuit Range/Performance Problem) and P0110 (Intake Air
Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction), P0120 (Throttle/Pedal
Position Sensor/Switch ºAº Circuit Malfunction) are output simultaneously, E2 (sensor ground) may be
open.

Read freeze frame data using TOYOTA hand±held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected, when troubleshooting it is useful for
determining whether the vehicle was running or stopped, the engine warmed up or not, the air±fuel
ratio lean or rich, etc. at the time of the malfunction.

± DIAGNOSTICSENGINE (5S±FE)
DI±33
268 Author: Date:
DTC P0106 Manifold Absolute Pressure Circuit
Range/Performance Problem
CIRCUIT DESCRIPTION
Refer to DTC P0105 (Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction) on page
DI±29.
DTC No.DTC Detecting ConditionTrouble Area
P0106
After engine is warmed up, conditions (a) and (b) continue with
engine speed 400 ~ 1,000 rpm
(2 trip detection logic)
(a) Throttle valve fully closed
(b) Manifold absolute pressure sensor output > 3.0 V

Manifold absolute pressure sensorP0106Condition (c) and (d) continue with engine speed 2,500 rpm or
less
(2 trip detection logic)
(c) VTA > 1.85
(d) Manifold absolute pressure sensor output < 1.0 V

Manifold absolute ressure sensor

Vacuum line
WIRING DIAGRAM
Refer to DTC P0105 (Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction) on page
DI±29.
INSPECTION PROCEDURE
HINT:

If DTC P0105 (Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction) and P0106 (Man-
ifold Absolute Pressure /Barometric Pressure Circuit Range/Performance Problem) are output simul-
taneously, manifold absolute pressure sensor circuit may be open. Perform troubleshooting of DTC
P0105 first.

If DTC P0105 (Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction), P0106 (Manifold
Absolute Pressure /Barometric Pressure Circuit Range/Performance Problem), P0110 (Intake Air
Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction) and P0120 (Throttle/
Pedal Position Sensor/Switch ºAº Circuit Malfunction) are output simultaneously, E2 (sensor ground)
may be open.

Read freeze frame data using TOYOTA hand±held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected, when troubleshooting it is useful for
determining whether the vehicle was running or stopped, the engine warmed up or not, the air±fuel
ratio lean or rich, etc. at the time of the malfunction.
1 Are there any other codes (besides DTC P0106) being output?
YES Go to relevant DTC chart.
NO
DI00N±04

A00310
Intake Air Temp. Sensor
E8
E83
9ECM
5 V
THA
E2
E1 R
Y±B
BR 2
1 DI±36
± DIAGNOSTICSENGINE (5S±FE)
271 Author: Date:
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTCs P0105 (Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction), P0106 (Man-
ifold Absolute Pressure /Barometric Pressure Circuit Range/Performance Problem), P0110 (Intake Air
Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction) and P0120 (Throttle/
Pedal Position Sensor/Switch ºAº Circuit Malfunction) are output simultaneously, E2 (sensor ground)
may be open.

Read freeze frame data using TOYOTA hand±held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected, when troubleshooting it is useful for
determining whether the vehicle was running or stopped, the engine warmed up or not, the air±fuel
ratio lean or rich, etc. at the time of the malfunction.

± DIAGNOSTICSENGINE (5S±FE)
DI±41
276 Author: Date:
DTC P0115 Engine Coolant Temp. Circuit Malfunction

CIRCUIT DESCRIPTION
A thermistor built into the engine coolant temp. sensor changes the resistance value according to the engine
coolant temp.
The structure of the sensor and connection to the ECM is the same as in the intake air temp. circuit malfunc-
tion shown on page DI±35.
If the ECM detects the DTC P0115, it operates fail safe function in which the engine coolant temperature
is assumed to be 80°C (176°F).
DTC No.Detection ItemTrouble Area
P0115Open or short in engine coolant temp. sensor circuit

Open or short in engine coolant temp. sensor circuit

Engine coolant temp. sensor

ECM
HINT:
After confirming DTC P0115, use the OBD II scan tool or TOYOTA hand±held tester to confirm the engine
coolant temp. from the CURRENT DATA.
Temp. DisplayedMalfunction
±40°C (±40°F)Open circuit
140°C (284°F) or moreShort circuit
DI00P±05

A00310
Engine Coolant Temp.
Sensor
2
1ECM
G±B
BR4
E8
E895 V
THW
E2
E1 R DI±42
± DIAGNOSTICSENGINE (5S±FE)
277 Author: Date:
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTCs P0105 (Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction), P0106 (Man-
ifold Absolute Pressure /Barometric Pressure Circuit Range/Performance Problem), P0110 (Intake Air
Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction) and P0120 (Throttle/
Pedal Position Sensor/Switch ºAº Circuit Malfunction) are output simultaneously, E2 (sensor ground)
may be open.

Read freeze frame data using TOYOTA hand±held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected, when troubleshooting it is useful for
determining whether the vehicle was running or stopped, the engine warmed up or not, the air±fuel
ratio lean or rich, etc. at the time of the malfunction.

A00395
ECM ON
Engine Coolant
Temp. Sensor
2
14
9
THW
E25 V
E1 E8
E8
± DIAGNOSTICSENGINE (5S±FE)
DI±43
278 Author: Date:
1 Connect OBD II scan tool or TOYOTA hand±held tester, and read value of
engine coolant temperature.
PREPARATION:
(a) Connect the OBD II scan tool or TOYOTA hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the OBD II scan tool or TOYOTA hand±held tester main switch
ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA hand±held tester.
OK:
Same as actual engine coolant temperature
HINT:

If there is open circuit, OBD II scan tool or TOYOTA hand±held tester indicates ±40°C (±40°F).

If there is open circuit, OBD II scan tool or TOYOTA hand-held tester indicates 140°C (284°F) or more.
NG ±40°C (±40°F) ... Go to step 2.
140°C (284°F) or more ... Go to step 4.
OK
Check for intermittent problems
(See page DI±3).
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the engine coolant temp. sensor connector.
(b) Connect the sensor wire harness terminals together.
(c) Turn the ignition switch ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA
hand±held tester.
OK:
Temperature value: 140°C (284°F) or more
OK Confirm good connection at sensor. If OK, re-
place engine coolant temp. sensor.
NG

A03012A03411
ON
4 Engine Coolant
Temp. Sensor
2
1ECM
THWE2
5 V
THW
E1 E8
E8
9E2
w/o Immobiliser
w/ Immobiliser
THW
E2
DI±44
± DIAGNOSTICSENGINE (5S±FE)
279 Author: Date:
3 Check for open in harness or ECM.
PREPARATION:
(a) Remove the glove compartment (See page SF±64).
(b) Connect between terminals THW and E2 of the ECM con-
nector.
HINT:
The engine coolant temp. sensor connector is disconnected.
Before checking, do a visual and contact pressure check for the
ECM connector (See page IN±31).
(c) Turn the ignition switch ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA
hand±held tester.
OK:
Temperature value: 140°C (284°F) or more
OK Open in harness between terminals E2 or THW,
repair or replace harness.
NG
Confirm good connection at ECM. If OK,
check and replace ECM (See page IN±31).

A00397
ON
Engine Coolant
Temp. Sensor
4
9ECM
E8
E8THW
E25 V
E1
± DIAGNOSTICSENGINE (5S±FE)
DI±45
280 Author: Date:
4 Check for short in harness and ECM.
PREPARATION:
(a) Disconnect the engine coolant temp. sensor connector.
(b) Turn the ignition switch ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA
hand±held tester.
OK:
Temperature value: ± 40°C (± 40°F)
OK Replace engine coolant temp. sensor.
NG