oil filter TOYOTA CAMRY 1999 Service Repair Manual

I00400
PlugAntenna
Terminal
(1) (2)
I00427
I00428
I00429I00408
Ground point:
Antenna Cord
Center Brace Luggage Room (RH side)
Pillar (LH) Noise Filter BE±90
± BODY ELECTRICALAUDIO SYSTEM
2310 Author: Date:
6. Fixed mast antenna:
GROUNDING FOR THE ANTENNA CORD AND CHOKE
COIL
HINT:
During troubleshooting, in case that the antenna code continu-
ity check, grounding check and grounding check of the choke
coil are needed, please check refering to the following illustra-
tions.
Terminal connectionNormal condition
(1) e (2)Continuity

I01472
Is the condition bad in comparison with other vehicle?
6 Radio POOR RECEPTION
An electric wave environment.
Is there any additional installation parts? (Sun shade film,
telephone antenna etc.).Does the condition get better if removing them? Ye s
No
Ye s
No
Check if there is any scratch and breaking in a
wire on the glass antenna and the defogger pattern.
(See page
BE±115)Influence of additional installation parts. No
Repair Ye s
No
No
Is the contact of the plug jack of the radio OK?
Check for contact.
Ye s
No
Does the condition get better by using the outer
antenna? (Such as pillar antenna)Check the radio.
Ye s
No
Ye s
No Is the contact of the antenna terminal on the glass
surface and the defogger terminal?Measure for contact.
Is the continuity of the antenna cord OK? Exchange the antenna cord.
Check the grounding of the antenna, antenna cord,
choke coil and noise filter.Ye s
NG
Grounding failure.
OK
Does the condition get better by exchanging the choke
coil?Exchange the choke coil. Ye s
No
Ye s
Does the condition get better by exchanging the
antenna cord?Exchange the antenna cord.
Exchange the glass.NoYe s
BE±98
± BODY ELECTRICALAUDIO SYSTEM
2318 Author: Date:

I01473
23 Noise NOISE OCCURS
Does the noise occur only in the radio? It occurs in the cassette CD. (Go to step 13 or 20)
Does the noise occur in a particular place? An electric environment.No
Ye s
Ye s
Is there any additional installation part around the glass
printed antenna? (Sunshade film, telephone antenna, etc.)Does the noise stop by removing it?
Influence of the film of the noise radiation of
additional installation part.
Does the noise occur even pulling out the antenna cord
from the radio?
Check the radio. No
No
NoNo Ye s
Ye s
Ye s
Does the noise occur even pulling out the antenna
terminal on the glass surface?Mixing into the antenna cable.
Is there any adhesive stuck on the bases of the
antenna terminal, defogger terminal and bus bar?Failure of glass installation. Must plane the butyl rubber.
Does the noise occur even pulling out the defogger
terminal?Interfering noise from the defogger line and choke
coil. Does the condition get better by exchanging the
choke coil? Ye s
Ye s
Ye s No
No
No
Check the grounding of the antenna, antenna cord,
choke coil and noise filter.Exchange the choke coil.
NG
Grounding failure.
Does the condition get better by exchanging the antenna
cord?
Radiates directly to the antenna from the generation
source.Exchange the antenna cord.
NoYe s OK
± BODY ELECTRICALAUDIO SYSTEM
BE±111
2331 Author: Date:

I00400
PlugAntenna
Terminal
(1) (2)
I00427
I00428
I00429I00408
Ground point:
Antenna Cord
Center Brace Luggage Room (RH side)
Pillar (LH) Noise Filter BE±90
± BODY ELECTRICALAUDIO SYSTEM
2310 Author: Date:
6. Fixed mast antenna:
GROUNDING FOR THE ANTENNA CORD AND CHOKE
COIL
HINT:
During troubleshooting, in case that the antenna code continu-
ity check, grounding check and grounding check of the choke
coil are needed, please check refering to the following illustra-
tions.
Terminal connectionNormal condition
(1) e (2)Continuity

I01472
Is the condition bad in comparison with other vehicle?
6 Radio POOR RECEPTION
An electric wave environment.
Is there any additional installation parts? (Sun shade film,
telephone antenna etc.).Does the condition get better if removing them? Ye s
No
Ye s
No
Check if there is any scratch and breaking in a
wire on the glass antenna and the defogger pattern.
(See page
BE±115)Influence of additional installation parts. No
Repair Ye s
No
No
Is the contact of the plug jack of the radio OK?
Check for contact.
Ye s
No
Does the condition get better by using the outer
antenna? (Such as pillar antenna)Check the radio.
Ye s
No
Ye s
No Is the contact of the antenna terminal on the glass
surface and the defogger terminal?Measure for contact.
Is the continuity of the antenna cord OK? Exchange the antenna cord.
Check the grounding of the antenna, antenna cord,
choke coil and noise filter.Ye s
NG
Grounding failure.
OK
Does the condition get better by exchanging the choke
coil?Exchange the choke coil. Ye s
No
Ye s
Does the condition get better by exchanging the
antenna cord?Exchange the antenna cord.
Exchange the glass.NoYe s
BE±98
± BODY ELECTRICALAUDIO SYSTEM
2318 Author: Date:

I01473
23 Noise NOISE OCCURS
Does the noise occur only in the radio? It occurs in the cassette CD. (Go to step 13 or 20)
Does the noise occur in a particular place? An electric environment.No
Ye s
Ye s
Is there any additional installation part around the glass
printed antenna? (Sunshade film, telephone antenna, etc.)Does the noise stop by removing it?
Influence of the film of the noise radiation of
additional installation part.
Does the noise occur even pulling out the antenna cord
from the radio?
Check the radio. No
No
NoNo Ye s
Ye s
Ye s
Does the noise occur even pulling out the antenna
terminal on the glass surface?Mixing into the antenna cable.
Is there any adhesive stuck on the bases of the
antenna terminal, defogger terminal and bus bar?Failure of glass installation. Must plane the butyl rubber.
Does the noise occur even pulling out the defogger
terminal?Interfering noise from the defogger line and choke
coil. Does the condition get better by exchanging the
choke coil? Ye s
Ye s
Ye s No
No
No
Check the grounding of the antenna, antenna cord,
choke coil and noise filter.Exchange the choke coil.
NG
Grounding failure.
Does the condition get better by exchanging the antenna
cord?
Radiates directly to the antenna from the generation
source.Exchange the antenna cord.
NoYe s OK
± BODY ELECTRICALAUDIO SYSTEM
BE±111
2331 Author: Date:

CO06C±03
S05299
w/ Oil Cooler
Oil Filter
Thermostat

Gasket
Water Inlet

Non±reusable part CO±10
± COOLING (5S±FE)THERMOSTAT
1584 Author: Date:
THERMOSTAT
COMPONENTS

CO06D±03
S05322
± COOLING (5S±FE)THERMOSTAT
CO±11
1585 Author: Date:
REMOVAL
HINT:
Removal of the thermostat would have an adverse effect, caus-
ing a lowering of cooling efficiency. Do not remove the thermo-
stat, even if the engine tends to overheat.
1. DRAIN ENGINE COOLANT
2. w/ Oil Cooler:
REMOVE OIL FILTER (See page LU±2)
3. REMOVE WATER INLET AND THERMOSTAT
(a) Remove the 2 nuts, and disconnect the water inlet from
the water pump cover.
(b) Remove the thermostat.
(c) Remove the gasket from the thermostat.

CO0SN±01
P13611
Protrusion
Jiggle
Valve5°5°
S05322
± COOLING (5S±FE)THERMOSTAT
CO±13
1587 Author: Date:
INSTALLATION
1. PLACE THERMOSTAT IN WATER INLET
(a) Install a new gasket to the thermostat.
(b) Align the jiggle valve of the thermostat with the protrusion
of the water inlet, and insert the thermostat in the water
inlet.
HINT:
The jiggle valve may be set within 5° of either side of the pre-
scribed position.
2. INSTALL WATER INLET AND THERMOSTAT
Install the water inlet and thermostat with the 2 nuts.
Torque: 8.8 N´m (90 kgf´cm, 78 in.´lbf)
3. w/ Oil Cooler:
INSTALL OIL FILTER (See page LU±2)
4. FILL WITH ENGINE COOLANT
5. START ENGINE AND CHECK FOR COOLANT LEAKS
6. CHECK ENGINE OIL LEVEL

P00495
Outside
Inside
± DIAGNOSTICSENGINE (5S±FE)
DI±9
244 Author: Date:
2 Is engine cranked?
NO Proceed to page ST±2 and continue to
troubleshoot.
YES
3 Does engine start?
NO Go to step 7.
YES
4 Check air filter.
PREPARATION:
Remove the air filter.
CHECK:
Visually check that the air filter is not dirty or excessive oily.
HINT:
If necessary, clean the filter with compressed air. First blow from
inside thoroughly, then blow from outside of the filter.
NG Repair or replace.
OK