trunk TOYOTA CAMRY 2000 Service Owner's Manual

N13159
N13160
I08491
GND
PRG
PRG
GND
Wireless Door
Lock ECU
Remote Control Mirror
Switch Connector
DI±804
± DIAGNOSTICSWIRELESS DOOR LOCK CONTROL SYSTEM
1039 Author: Date:
(d) Replace the battery for transmitter.
(1) Using a screwdriver, pry outward the cover.
(2) Remove the battery.
(3) Set a new battery into the transmitter.
(4) Install the cover to the transmitter.
3. REGISTRATION OF RECOGNITION CODE
The recognition code of the transmitter is electronically regis-
tered (written to and stored) in an EEPROM contained in the
wireless door lock ECU. This makes it possible to register up to
2 different codes in the EEPROM.
New recognition codes can be registered after all previous
codes have been erased. A transmitter code can be registered
into the EEPROM by following the steps numbered (1) to (5).
(1) The wireless door lock ECU and remote control mir-
ror switch are connected to each other via a PRG
terminal, and the GND terminal of the remote con-
trol mirror switch connector is grounded to body.
Remove the connector from the remote control mir-
ror switch, and use a test lead to short the PRG and
GND connector together. As a result, the PRG ter-
minal of the wireless door lock ECU will be
grounded to body and will cause all transmitter rec-
ognition codes previously registered in the EE-
PROM to be erased. At the same time, the ECU will
respond by operating once the lock and unlock
functions of all the doors, and the open function of
the trunk lid.

Toyota Supports ASE CertificationPage 1 of 1
AX001-01Title:
RETRO-FIT INTERNAL TRUNK
RELEASE KITS
Models:
All Applicable '90 ± '00 Models
Technical Service
BULLETIN
March 9, 2001

In order to respond to requests of our valued customers, we are offering Retro±Fit
Internal Trunk Release Kits. These kits allow the trunk to be opened from the inside in
case of entrapment.
MODELMODEL CODEMODEL YEAR# CLAMPS
AvalonMCX101995 ± 19994AvalonMCX2020004
CamrySXV10, MCV10, VCV101992 ± 19964CamrySXV20, MCV201997 ± 20004
Celica (Coupe)AT200, ST2041994 ± 19994
Corolla (Sedan)AE10#1993 ± 19974Corolla (Sedan)ZZE1101998 ± 20005
ECHONCP1220004
MR2SW20, 211990 ± 19952
PaseoEL441992 ± 19954PaseoEL541996 ± 19994
SolaraSXV20, MCV201999 ± 20004
TercelEL421991 ± 19944TercelEL531995 ± 19994
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
±64640±33030Trunk Release
±64610±17040Trunk Release (MR2 Only)
±90464±00551Clamp
±MDC 00107±00316±TRInstallation Instructions
Order the appropriate trunk release, at least as many clamps as listed above, and a set
of installation instructions. Follow the installation procedure detailed in the installation
instructions. Installation time is 0.7 hours.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
ACCESSORIES
Introduction
Applicable
Vehicles
Parts
Information
Installation
Procedure
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 2
AX003±00Title:
PORT INSTALLED RS3000 TVIP TRUNK
COURTESY CONNECTION
Models:
'99 Camry
Technical Service
BULLETIN
March 31, 2000

The trunk courtesy connection for 1999 model year Camry vehicles equipped with a Port
Installed Option RS3000 (V3) has been relocated from the luggage compartment light
switch to below the dash (lower finish panel) on the driver's side in the Instrument Panel
J/B. (Refer to Illustrations A & B on page 2.)
The location was changed to improve the installation process.
A splicing connector is used for the new trunk courtesy wire installation (blue) to the
vehicle's wire harness at Instrument Panel J/B (red/yellow).
The previous location is the same as the dealer installed RS3000 trunk courtesy
connection to the luggage compartment light switch connection.
For service related purposes, this bulletin describes the procedures to locate the new
trunk courtesy connection at Instrument Panel J/B in vehicles equipped with PIO
RS3000.
The remote transmitter has two
buttons, Top and Bottom.The status monitor has a Toyota label,
LED, and microphone.
Remote Control
LED
Status Monitor
Microphone
1999 model year Camry vehicles equipped with PIO (V3) TVIP.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
ACCESSORIES
Introduction
Applicable
Vehicles
Warranty
Information

PORT INSTALLED RS3000 TVIP TRUNK COURTESY CONNECTION ± AX003±00 March 31, 2000
Page 2 of 2
New Location:
These steps below are to be followed to
locate the new trunk courtesy connection
when servicing Camry vehicles equipped
with the PIO RS3000 TVIP.
1. Remove the negative battery cable.
2. Remove the driver's step cover.
3. Remove the driver's cowl cover (1
nut).
4. Locate the Connector Junction Block
in the driver's cowl area. You will
notice a RED/YELLOW wire routed to
the Blue 10P connector which
terminates at an adjacent splicing
connector. This is the TVIP Trunk
Courtesy Wire.
5. Disconnect the Blue 10P connector
from the Connector Junction Block.
With the tab of the Blue 10P
connector facing up, look at the back
(wire side) and locate the wire in the
bottom row, second space from the
right, which has the splicing connector
attached to it. This is the Vehicle's
Trunk Courtesy Signal Wire.
6. After completing the parts inspection
and repairs if applicable, reconnect
the Blue 10P connector and install all
previously removed parts.
Previous Location:
The White 1P connector for the Vehicle's
Trunk Courtesy Signal is located at the
trunk courtesy lamp switch near the trunk
latch in the vehicle's trunk.
Locating
Procedure
Connector
Junction Block
Illustration A
10P
Connector
(Blue)
TVIP Trunk
Courtesy Wire
(Yellow/Red)
Illustration B
Splicing
Connector
10P
Connector
(Blue)
Wire Side View

TSB
Title:
1997 CAMRY REAR SPOILER INSTALLATION
Models:
`97 Camry
IntroductionUpon installation of the rear spoiler, as outlined in the Dealer Installation Instruction sheet
enclosed with the spoiler, please follow the outlined procedure for verification of the trunk
lid operation:
Affected1997 Model Year Camry.
Vehicles
Procedure1. Reinstall the carpet trim panel on the
inside of the trunk lid with the
appropriate fasteners.
2. The trunk lid must remain open and
hold its position, up to approximately
45 degrees from horizontal as shown.
3. If the trunk lid does not hold its open
position and the trunk lid closes:
a. Move the end of one of the torsion
rods to the next upper open slot.
b. Verify that the trunk lid functions
as outlined above.
c. If the condition is not corrected,
adjust the other torsion bar to
the next upper open slot position.
4. If the trunk lid does not hold its open
position and the trunk lid opens fully
forcibly:
a. Move the end of one of the torsion
rods to the next lower open slot
position.
b. Verify that the trunk lid functions
as outlined above.
c. If the condition is not corrected,
please adjust the other torsion
bar to the next lower open slot
position.
ACCESSORY
April 25, 1997
Page 1 of 1
AX005-97
NOTE:
Upon completion of the procedure
described in this bulletin, please refer
to the Dealer Installation Instructions
for final checks.
Upper Slot
Lower Slot

Toyota Supports ASE CertificationPage 1 of 1
BO028-00Title:
LEAKS INTO TRUNK
Models:
'97 - '01 Camry (U.S.), '98 - '01 Sienna,
'99 - '01 Solara & '01 Avalon
Technical Service
BULLETIN
November 3, 2000

A field fix is available for incidents of moisture and odors permeating into the vehicle.
The Quarter Panel Air Duct flaps may have become loose or missing. Replacing the
Quarter Panel Air Duct will remedy the condition.
1997 ± 2001 model year Camry (U.S. produced)
1998 ± 2001 model year Sienna
1999 ± 2001 model year Solara
2001 model year Avalon
MODELSTARTING VIN
2001 MY Camry, 4 cylinder4T1BG22K81U019710
4T1BG22KB1U768622
2001 MY Camry, 6 cylinder4T1BF28K11U116208
4T1BF22K51U958204
2001 MY Sienna4T3ZF13C#1U335575
2001 MY Solara2T1CF22P#1C435983
2001 MY Solara Convertible2T1FF28P#1C435448
2001 MY Avalon4T1BF28B11U123532
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
62940-AA01062940-AA011Quarter Panel Air Duct
Replace the Quarter Panel Air Duct.
OP CODEDESCRIPTIONTIMEOPNT1T2
BD0036R & R Quarter Panel Air Duct1.062940-AA0106257
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Repair
Procedure
Warranty
Information