check engine TOYOTA CAMRY 2000 Service Repair Manual

DI1KH±03
DI±924
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1159 Author: Date:
DIAGNOSTIC TROUBLE CODE CHART
DTC No.
(See page)Detection ItemTrouble Area
B2795
(DI±928)Unmatched key code
Key

Unregistered key inserted before
B2796
(DI±929)No communication in immobiliser system

Key

Transponder key coil

Amplifier

Wirehaness

ECM
B2797
(DI±932)Communication malfunction No.1
Communication contests

Unregistered key inserted before
B2798
(DI±935)Communication malfunction No.2

Key

Transponder key coil

Amplifier

Wirehaness

ECM
HINT:
To reduce the unnecessary exchange of ECM, check that a trouble occurs with the original ECM at the time
of exchanging ECM and the trouble will disappear with a new ECM.

DI1KK±03
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±927
1162 Author: Date:
PROBLEM SYMPTOMS TABLE
SymptomSuspect AreaSee page
Immobiliser is not set.
(Engine starts with key codes other than the registered key code.)2. ECMIN±31
Engine does not start.
1. Key
2. Wire harness
3. Transponder key coil
4. Amplifier
5. ECM*1
IN±31
BE±128
IN±31
Security indicator is always ON.
1. Security indicator
2. Wire harness
3. ECM*2
IN±31
IN±31
Security indicator is always ON.
(Although code has been registered in the automatic registration
mode, indicator is not OFF.)1. Wire harness
2. Transponder key coil
3. Amplifier
4. ECMIN±31
BE±128
IN±31
Security indicator is OFF
(When DTC of immobiliser is output)
1. Wire harness
2. Transponder key coil
3. Amplifier
4. ECMIN±31
BE±128
IN±31
Security indicator is OFF.
(When DTC of immobiliser is not output)1. Wire harness
2. ECMIN±31
IN±31
Security indicator is abnormally brinking.1. Wire harness
2. ECMIN±31
IN±31
*1 : Check that the key which did not start the engine has been registered and that it is possible to start with
other already registered key codes.
*2 : Finish the automatic registration mode because the mode might still remain.

DI1KN±02
DI±928
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1163 Author: Date:
CIRCUIT INSPECTION
DTC B2795/99 Unmatched Key Code
This DTC is output when an unregistered key is inserted. When this DTC is output, delete DTC and insert
the key that a customer keeps to check that B2795 is output.
When a key that outputs B2795 is found, register this key. When B2795 is not output, there is a possibility
that the unregistered key has been inserted before. (ECM is normal.)
Inquire of a customer about the condition of using the system to find the cause of the trouble.
(Example: Another key has been inserted, etc.)

± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±931
1166 Author: Date:
INSPECTION PROCEDURE
1 Check transponder key coil (See page BE±128).
NG Replace transponder key coil.
OK
2 Check harness and connector between transponder key amplifier and ECM.
NG Repair or replace harness and connector.
OK
3 Does it operate normally after replacement of transponder key amplifier?
Yes Replace transponder key amplifier.
No
Replace ECM.

I02681
Noise
DI±934
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1169 Author: Date:
INSPECTION PROCEDURE
1 Noise check
PREPARATION:
Insert already registered master key in the key cylinder.
CHECK:
Using an oscilloscope or TOYOTA hand±held tester, check that
noise is included in the CODE terminal of ECM.
OK:
No noise is detected.
NG Try to find the cause of the noise and remove it.
OK
2 Does it operate normally after replacement of transponder key amplifier?
Yes Replace transponder key amplifier.
No
Replace ECM.

± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±937
1172 Author: Date:
INSPECTION PROCEDURE
1 Check transponder key coil (See page BE±128).
NG Replace transponder key coil
OK
2 Check harness and connector between transponder key amplifier and ECM.
NG Repair or replace harness and connector
OK
3 Does it operate normally after replacement of transponder key amplifier?
Yes Replace transponder key amplifier.
No
Replace ECM.

EC03E±05
B01082B04812B06707
Type A
Type BGasket
Gasket
B06544
Vacuum
Gauge
S05331
EC±6
± EMISSION CONTROL (5S±FE)EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM
1404 Author: Date:
INSPECTION
1. INSPECT LINES AND CONNECTORS
Visually check for loose connections, sharp bends or damage.
2. INSPECT FUEL TANK FILLER PIPE
Visually check for deformation, cracks or fuel leakage.
3. INSPECT FUEL TANK CAP
Visually check if the cap and/or gasket are deformed or dam-
aged.
If necessary, repair or replace the cap.
4. INSPECT EVAP SYSTEM LINE
(a) Warm up the engine and stop the engine.
Allow the engine to warm up to normal operating tempera-
ture.
(b) Install a vacuum gauge (EVAP control system test equip-
ment vacuum gauge) to the EVAP service port on the
purge line.
(c) TOYOTA Hand±Held Tester:
Forced driving of the VSV for the EVAP.
(1) Connect a TOYOTA hand±held tester to the DLC3.
(2) Start the engine.
(3) Push the TOYOTA hand±held tester main switch
ON.
(4) Use the ACTIVE TEST mode on the TOYOTA
hand±held tester to operate the VSV for the EVAP.

B06548Battery
B06545
B06543
Hose Clipper
Air Drain Hose
± EMISSION CONTROL (5S±FE)EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM
EC±7
1405 Author: Date:
(d) If you have no TOYOTA Hand±Held Tester:
Forced driving of the VSV for the EVAP.
(1) Disconnect the VSV connector for the EVAP.
(2) Connect the positive (+) and negative (±) leads from
the battery to the VSV terminals for the EVAP.
(3) Start the engine.
(e) Check the vacuum at idle.
Vacuum:
Maintain at 0.368 ± 19.713 in.Hg (5 ± 268 in.Aq) for over
5 seconds
HINT:
If the vacuum does not change, you can conclude that the hose
connecting the VSV to the service port has come loose or is
blocked, or the VSV is malfunctioning.
(f) TOYOTA Hand±Held Tester:
Conclude forced driving of the VSV for the EVAP.
(1) Stop the engine.
(2) Disconnect the TOYOTA hand±held tester from the
DLC3.
(g) If you have no TOYOTA Hand±Held Tester:
Conclude forced driving of the VSV for the EVAP.
(1) Stop the engine.
(2) Disconnect the positive (+) and negative (±) leads
from the battery from the VSV terminals for the
EVAP.
(3) Connect the VSV connector for the EVAP.
(h) Disconnect the vacuum gauge from the EVAP service
port on the purge line.
(i) Connect a pressure gauge to the EVAP service port on
the purge line.
(j) Check the pressure.
(1) Close off the air drain hose at the marked position
of the canister with a hose clipper or similar instru-
ment.

EC03G±04
S05568
Cap
Filter
B06540
Vacuum Gauge
3±Way Connector
A07370
SST
E1
TE1
B06541
HOTHigh Vacuum at 2,500 rpm
Port R
Disconnect
EC±12
± EMISSION CONTROL (5S±FE)EXHAUST GAS RECIRCULATION (EGR) SYSTEM
1410 Author: Date:
INSPECTION
1. INSPECT EGR SYSTEM
(a) Inspect and clean the filter in the EGR vacuum modulator.
(1) Remove the cap and filter.
(2) Check the filter for contamination or damage.
(3) Using compressed air, clean the filter.
(4) Reinstall the filter and cap.
HINT:
Install the filter with the coarser surface facing the atmospheric
side (outward).
(b) Using a 3±way connector, connect a vacuum gauge to the
hose between the EGR valve and VSV.
(c) Inspect seating of the EGR valve.
Start the engine and check that the engine starts and runs
at idle.
(d) Using SST, connect terminals TE1 and E1 of the DLC1.
SST 09843±18020
(e) Inspect the VSV operation with the cold engine.
(1) The engine coolant temperature should be below
55°C (131°F).
(2) Check that the vacuum gauge indicates zero at
2,500 rpm.
(f) Inspect the operation of the VSV and EGR vacuum modu-
lator with the hot engine.
(1) Warm up the engine to above 60°C (140°F).
(2) Check that the vacuum gauge indicates low vacu-
um at 2,500 rpm.
(3) Disconnect the vacuum hose port R of the EGR vac-
uum modulator and connect port R directly to the in-
take manifold with another hose.
(4) Check that the vacuum gauge indicates high vacu-
um at 2,500 rpm.

B06539
Disconnect
S05567
Air Engine Stopped
S05566
Engine at
2,500 rpm
Air
± EMISSION CONTROL (5S±FE)EXHAUST GAS RECIRCULATION (EGR) SYSTEM
EC±13
1411 Author: Date:
HINT:
As a large amount of exhaust gas enters, the engine will misfire
slightly.
(g) Remove the vacuum gauge, and reconnect the vacuum
hoses to the proper locations.
(h) Inspect the EGR valve.
(1) Apply vacuum directly to the EGR valve with the en-
gine idling.
(2) Check that the engine runs rough or dies.
(3) Reconnect the vacuum hoses to the proper loca-
tions.
HINT:
As exhaust gas is increasingly recirculated, the engine will start
to misfire.
(i) Remove the SST from the DLC1.
SST 09843±18020
2. INSPECT EGR VACUUM MODULATOR
(a) Disconnect the vacuum hoses from ports P, Q and R of
the EGR vacuum modulator.
(b) Block ports P and R with your finger.
(c) Blow air into port Q, and check that the air passes through
to the air filter side freely.
(d) Start the engine, and maintain speed at 2,500 rpm.
(e) Repeat the above test. Check that there is a strong resis-
tance to air flow.
(f) Reconnect the vacuum hoses to the proper locations.