check engine TOYOTA CAMRY 2000 Service Repair Manual

3
CAMRY ± OUTLINE OF NEW FEATURES27
8. Brakes
The specifications of the front and rear brakes have been changed.
9. Suspension
The front and rear springs, stabilizers, and shock absorbers have been modified to realize excellent stability,
controllability, and riding comfort.
10. Steering
A check valve has been added to the power steering gear box to help reduce kickback.
The rack stroke of the 5S-FE engine model has been changed to 145mm (5.71 in.), which is the same as
in the 1MZ-FE engine.
11. Body
Hood support dampers are used.
Two utility hooks added in the luggage room for the gasoline engine model.
To install the fuel tank in the front area of the luggage compartment, the upper back panel has been cut
out for the 5S-FNE engine model.
A performance rod that joins the tops of the right and left rear suspension strut towers has been adopted
for the 5S-FNE engine model.
The shape of the rear floor pan has been changed to prevent the luggage compartment capacity from being
reduced as a result of the installation of the fuel tank in the luggage compartment for the 5S-FNE engine
model.
12. Seat
The seat cover of the LE grade model has been changed.
Optional driver power seat added for the LE grade model.
A fixed type seat back is used for the rear seat for the 5S-FNE engine model.
13. Seat Belt
2-point NR (Non-Retractor) seat belt is used for the rear center seat for the 5S-FNE engine model.
14. Wireless Door Lock Control
Audio answer back is adopted.
15. Lighting
Along with the adoption of the 4-beam headlights, the electrical circuit of the daytime running light system
has been changed.
16. Air Conditioning
The air inlet mode selector of heater control panel has been changed from the lever type to the push button
type on the CE and LE grade model.
When the air outlet mode is set to the DEF or FOOT / DEF mode, the air inlet mode also changes to the
FRESH mode, has been also added on the CE and LE grade model.
A fully automatic controlled type air conditioning is used on the XLE grade model.
A defroster-linked air conditioning start up control has been continuing to use since the previous models
with air conditioning.
17. SRS Airbag
The inflator of the SRS airbag for the driver has been made more compact and lightweight.
A signal that causes the supply of fuel to be cut off during a frontal collision is output by the airbag sensor
assembly to the ECM for the 5S-FNE engine model.

3
CAMRY ± NEW FEATURES
172CM14
Fuel
Pressure
SensorFuel Temp.
SensorFuel
Pressure
RegulatorFuel Shutoff ValveFuel Tank
Fuel Shutoff ValveRelief Valve
Inlet Check
Valve
Fuel Temp.
Sensor
Coupler
Tank Valve Assembly
Vent Tube Manual
Shutoff
Valve Oil
Separator
Fuel Shutoff Valve Injectors
Delivery Pipe Discharge
ValveFuel
Pressure
SensorFuel
Filter43
6. Fuel System
General
The compressed gas [maximum pressure approximately 250 kg / cm
2 (3600 psi, 24.8 MPa) @ 21C
(70F)] from the CNG fuel tank located in the rear section of the vehicle is routed via a fuel filter to the
engine compartment. The pressure of the fuel is then reduced to 8 kg / cm
2 (114 psi, 785 kPa).
A pressure regulator and injectors designed exclusively for CNG application have been adopted.
A fuel pressure sensor and a fuel temperature sensor that are used for the correction of the fuel injection
volume are located on the delivery pipe.
The fuel tank, pressure regulator, and the delivery pipe are provided with shutoff valves that shut off the
fuel when the ignition switch is turned OFF.
In addition, these valves shut off the fuel when the engine stalls, the SRS airbag is deployed, or the pres-
sure in the main pipe becomes abnormally low.
A fuel temperature sensor for the fuel gauge is mounted on the tank valve assembly, and a fuel pressure
sensor is mounted immediately upstream of the pressure regulator.

Fuel System Diagram 

3
CAMRY ± NEW FEATURES
172CM17
CloseOpen45
2) Fuel Shutoff Valve for Fuel Tank
This valve uses an solenoid valve. The main pipe that supplies compressed gas to the engine is connected
to this valve, which opens when the ignition switch is turned ON. If the engine stalls, this valve automati-
cally shuts off the fuel even if the ignition switch is turned ON. The valve reopens upon restarting the
engine.
Also, this valve shuts off the fuel if the SRS airbag is deployed in a collision or if the pressure in the main
pipe becomes abnormally low.
3) Inlet Check Valve
Connected to a filler pipe that guides the fuel that fills through the coupler, the inlet check valve shuts
off by the force of a spring and by the pressure of the gas in the tank.
During filling, the pressure of the filling gas opens the inlet check valve.
4) Relief Valve
A vent tube is connected to this valve.
If the fuel tank is exposed to an abnormally high temperature, this valve opens (by melting) to discharge
the CNG at a predetermined temperature, thus helping prevent the fuel tank from bursting due to the in-
crease in gas pressure.
The discharged CNG is guided under the floor through a vent tube and is released outside of the vehicle.
Coupler
The coupler allows the fuel to be filled when it is connected with a fuel filling nozzle. The coupler has a
built-in check valve to help prevent the CNG from flowing backward.
Manual Shutoff Valve
This valve is mounted below the vehicle floor.
When servicing the vehicle, this valve can be
manually turned 90 degrees to shut off the main
pipe.

3
CAMRY ± NEW FEATURES
172CM18
172CM19
ON
OFF1 sec 1 sec
1 sec 1 sec
ON
OFF1 sec 1 sec
2 sec 2 sec 2 sec53
Injector Control
1) General
Fuel clearing control and injector unsticking control have been added to the injector control.
2) Fuel Clearing Control
While the vehicle is being driven at speeds higher than 60 km / h (37.5 mph), and the ignition switch is
turned OFF after the ECM has detected a low temperature condition of less than 25C (77F) of intake
air temperature, the ECM closes the fuel shutoff valve for the delivery pipe. However, instead of immedi-
ately stopping the engine, the fuel clearing control allows the engine to stop on its own after the fuel in
the delivery pipe has been used up. If the engine is running even after 2 seconds or more have elapsed
after the ignition switch has been turned OFF, the EFI relay is turned OFF to stop the engine.
3) Injector Unsticking Control
When the ignition switch is turned ON after executing the fuel clearing control, the injector unsticking
control activates two cylinders at a time to unstick the valve that is frozen stuck onto the valve seat. At
low temperature conditions. At this time, the shutoff valve remains closed so that the injectors will not
inject fuel.
Gas Leak Judgment
If the ECM has detected a gas leak through the signals received from the pressure sensors, the ECM closes
the shutoff valves and flashes the low fuel level warning light.
These functions are canceled by resetting the ECM (by disconnecting the negative [-] terminal of the bat-
tery), which enables the engine to start.
(The ECM should be reset only after performing a gas leak check and making sure that the leak has been
eliminated.)
NOTE: The low fuel level warning light also flashes when the fuel level is extremely low. The flashing
patterns shown below differentiates a gas leak from a low fuel level.
Flashing Pattern
Gas Leak
Fuel Low Level

(09248±05011) Valve Lifter Press
(09248±05021) Valve Lifter Stopper
09226±10010 Crankshaft Front & Rear Bearing
Replacer
09616±30011 Steering Worm Bearing Adjusting
Screw Wrench09224±74010 Engine Balancer Backlash
Adjusting Tool
09330±00021 Companion Flange Holding Tool09248±55020 Valve Clearance Adjust Tool Set
RECOMMENDED TOOLS
09816±30010 Oil Pressure Switch Socket09278±54012 Drive Shaft Holding Tool09249±63010 Torque Wrench Adaptor
09843±18020 Diagnosis Check Wire
09090±04010 Engine Sling Device
09200±00010 Engine Adjust KitCamshaft timing pulley
For suspension engineCrankshaft pulley
Oil pump pulley
Knock sensor
± 5S±FE ENGINEENGINE MECHANICALEG1±5

ENGINE OIL INSPECTION
1. CHECK OIL QUALITY
Check the oil for deterioration, entry of water, dis±
coloring or thinning.
If oil quality is visibly poor, replace it.
Oil grade:
API grade SG or SH, Energy Conserving II multi±
grade engine oil or ILSAC multigrade engine oil.
Recommended viscosity is as shown in the illustra±
tion.
TUNE±UP
ENGINE COOLANT INSPECTION
1. CHECK ENGINE COOLANT LEVEL AT RESERVOIR
TANK
The engine coolant level should be between the
ªLOWº and ªFULLº lines at low temperature.
If low, check for leaks and add engine coolant up to
the ªFULLº
2. CHECK ENGINE COOLANT QUALITY
There should be no excessive deposits of rust or
scales around the radiator cap or radiator filler hole,
and the engine coolant should be free from oil.
If excessively dirty, replace the engine coolant.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ªLº and ªFº marks
on the dipstick.
If low, check for leakage and add oil up to the ªFº
mark.
± 5S±FE ENGINEENGINE MECHANICALEG1±8

2. Except Delco Battery:
CHECK BATTERY VOLTAGE AND SPECIFIC
GRAVITY
A. Maintenance Free Battery
Measure the battery voltage between the terminals
negative (±) and positive (+) of the battery.
Standard voltage:
12.7 ± 12.9 V at 205C (685F)
HINT:
wBefore measuring the voltage, turn the ignition
switch to LOCK and turn off the electrical sys±
tems (headlight, blower motor, rear defogger etc.)
for 60 seconds to remove the surface charge.
wIf the vehicle has been running, wait 5 minutes or
more after the vehicle stops before measuring
the battery voltage.
If the voltage is less than specification, charge the
battery.
HINT: Check the indicator as shown in the illustration. 1. Except Delco Battery:
CHECK BATTERY ELECTROLYTE LEVEL
Check the electrolyte quantity of each cell.
A. Maintenance Free Battery
If under the lower level, replace the battery (or add
distilled water if possible). Check the charging system.
B. Except Maintenance Free Battery
If under the ªLOWERº or ªMINº line, add distilled
water.
BATTERY INSPECTION
± 5S±FE ENGINEENGINE MECHANICALEG1±9

3. Delco Battery:
CHECK HYDROMETER
Green Dot visible:
Battery is adequately charged
Dark (Green Dot not visible):
Battery must be charged
Clear or Light Yellow:
Replace battery
HINT: There is no need to add water during the entire
service life of the battery.
AIR FILTER INSPECTION
1. INSPECT AIR FILTER
Visually check that the element is not excessively
dirty, damaged or oily.
2. CLEAN AIR FILTER
Clean the element with compressed air.
First blow air from the inside thoroughly. Then blow
off the outside of the element.B. Except Maintenance Free Battery
Check the specific gravity of each cell.
Standard specific gravity:
55D23L battery for GNB Incorporated
1.25 ± 1.27 at 205C (685F)
55D23L battery for JOHNSON CONTROLS
1.26 ± 1.28 at 275C (815F)
80D26L battery for GNB Incorporated
1.27 ± 1.29 at 205C (685F)
80D26L battery for JOHNSON CONTROLS
1.28 ± 1.30 at 27
C (81
F)
If the gravity is less than specification, charge the
battery.
HINT: Check the indicator as shown in the illustration.
HIGH±TENSION CORDS INSPECTION
1. DISCONNECT HIGH±TENSION CORDS FROM
SPARK PLUGS
Disconnect the high ± tension cords at the rubber
boot. Do not pull on the high±tension cords.
NOTICE: Pulling on or bending the cords may damage the
conductor inside.
± 5S±FE ENGINEENGINE MECHANICALEG1±10

GENERATOR DRIVE BELT INSPECTION
INSPECT DRIVE BELT
(a) Visually check the drive belt for excessive wear,
frayed cords etc.
If any defect has been found, replace the drive belt.
HINT: Cracks on the rib side of a drive belt are consid±
ered acceptable. If the drive belt has chunks missing
from the ribs, it should be replaced.4. INSPECT HIGH±TENSION CORD RESISTANCE
Using an ohmmeter, measure the resistance.
Maximum resistance:
25 k
per cord
If the resistance is greater than maximum, check the
terminals. If necessary, replace the high ± tension
cord.
5. RECONNECT HIGH±TENSION CORDS TO
DISTRIBUTOR CAP
6. CALIFORNIA ONLY:
RECONNECT HIGH±TENSION CORD TO IGNITION
COIL
7. RECONNECT HIGH±TENSION CORDS TO SPARK
PLUGS2. CALIFORNIA ONLY:
DISCONNECT HIGH±TENSION CORD FROM
IGNITION COIL
3. DISCONNECT HIGH ±TENSION CORDS FROM
DISTRIBUTOR CAP
(b) Using a belt tension gauge, measure the belt tension.
Belt tension gauge:
Nippondenso BTG±20 (95506±00020)
Borroughs No. BT±33±73F
± 5S±FE ENGINEENGINE MECHANICALEG1±11

Drive belt tension:
w/ A/C
New belt
175 + 5 lbf
Used belt
130 + 10 lbf
w/o A/C
New belt
125 + 25 lbf
Used belt
95 + 20 lbf
If the belt tension is not as specified, adjust it.
HINT:
wªNew beltº refers to a belt which has been used
less than 5 minutes on a running engine.
wªUsed beltº refers to a belt which has been used
on a running engine for 5 minutes or more.
wAfter installing a belt, check that it fits properly in
the ribbed grooves.
wCheck with your hand to confirm that the belt has
not slipped out of the groove on the bottom of
the pulley.
wAfter installing a new belt, run the engine for
about 5 minutes and recheck the belt tension.
VALVE CLEARANCE INSPECTION AND
ADJUSTMENT
HINT: Inspect and adjust the valve clearance when
the engine is cold.
1. DISCONNECT HIGH ± TENSION CORDS FROM
SPARK PLUGS
Disconnect the high ± tension cords at the rubber
boot. DO NOT pull on the cords.
NOTICE: Pulling on or bending the cords may damage the
conductor inside.
2. REMOVE CYLINDER HEAD COVER
(a) Disconnect the PCV hoses.
(b) Loosen the 2 wire harness clamp bolts (No.2 timing
belt cover) mounting bolts.
(c) Remove the 4 nuts, grommets, head cover and gasket.
± 5S±FE ENGINEENGINE MECHANICALEG1±12