key TOYOTA CAMRY 2000 Service Repair Manual

4. TEMPORARILY INSTALL NO.1 IDLER PULLEY AND
TENSION SPRING
(a) Install the pulley with the bolt. Do not tighten the bolt
yet.
HINT: Use a bolt 42 mm (1.65 in.) in length.
(b) Install the tension spring.
(c) Pry the pulley toward the left as far as it will go and
tighten the bolt.
(d) Check that the idler pulley moves smoothly.
5. TEMPORARILY INSTALL TIMING BELT
NOTICE: The engine should be cold.
(a) Using the crankshaft pulley bolt, turn the crankshaft
and position the key groove of the crankshaft timing
pulley upward.
(b) Remove any oil or water on the crankshaft pulley, oil
pump pulley, water pump pulley, No. 1 idler pulley, No.
2 idler pulley and keep them clean.
(c) Install the timing belt on the crankshaft timing pulley,
oil pump pulley, No.1 idler pulley, water pump pulley
and No.2 idler pulley.
HINT (When re±using timing belt): Align the points
marked during removal, and install the belt with the
arrow pointing in the direction of engine revolution. 2. INSTALL CRANKSHAFT TIMING PULLEY
(a) Align the timing pulley set key with the key groove of
the pulley.
(b) Slide on the timing pulley, facing the flange side
inward.
3. INSTALL NO.2 IDLER PULLEY
(a) Install the pulley with the bolt.
Torque: 42 N±m (425 kgf±cm, 31 ft±lbf)
HINT: Use a bolt 35 mm (1.38 in.) in length.
(b) Check that the idler pulley moves smoothly.
± 5S±FE ENGINEENGINE MECHANICALEG1±34

9. INSTALL CAMSHAFT TIMING PULLEY
(a) Align the camshaft knock pin with the knock pin
groove of the pulley, and slide on the timing pulley.
(b) Using SST, install the plate washer and bolt.
SST 09249 ± 63010 and 09278 ± 54012
Torque: 37 N±m (380 kgf±cm, 27 ft±lbf)
HINT: Use a torque wrench with a fulcrum length of
340 cm (13.39 in.)8. INSTALL CRANKSHAFT PULLEY
(a) Align the pulley set key with the key groove of the
pulley, and slide on the pulley.
(b) Using SST, install the pulley bolt.
SST 09213±54015 (91651 ±60855)
09330±00021
Torque: 108 N±m (1,100 kgf±cm, 80 ft±lbf)
10. SET No.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley, and align its groove with
timing mark ª0º of the No.1 timing belt cover. 7. INSTALL NO.1 TIMING BELT COVER
(a) Install the gasket to the timing belt cover.
(b) Install the timing belt cover with the 4 bolts. 6. INSTALL TIMING BELT GUIDE
Install the guide, facing the cup side outward.
± 5S±FE ENGINEENGINE MECHANICALEG1±35

OIL PUMP INSTALLATION
(See Components for Removal and Installation)
1. INSTALL OIL PUMP
Install a new gasket and the oil pump with the 12
bolts.
Torque: 9.3 N±m (95 kgf±cm, 82 in.±lbf)
HINT: Long bolts are indicated in the illustration.
Bolt length:
Long bolt
35 mm (1.38 in.)
Others
25 mm (0.98 in.)
3. INSTALL CRANKSHAFT TIMING PULLEY
(a) Align the timing pulley set key with the key groove of
the pulley.
(b) Slide on the timing pulley, facing the flange side
inward. 2. INSTALL OIL PUMP PULLEY
(a) Align the cutouts of the pulley and shaft, and slide on
the pulley.
(b) Using SST, install the nut.
SST 09616±30011
Torque: 28 N±m (290 kgf±cm, 21 ft±lbf)
± 5S±FE ENGINELUBRICATION SYSTEMEG1±283

22
INTERIOR

Layout of Audio System
 TILT STEERING
The tilt steering is standard on all models.
The steering wheel position can be changed to any of 6 positions..
 POWER WINDOW SYSTEM
A power window system is standard on the LE and XLE grade models and optional on the CE grade model. The power
window system includes one±touch auto down and key±off operation functions. The one±touch auto down function
automatically opens the driver's side window fully. The key±off operation function makes it possible to operate the
power windows for approximately 45 seconds after the ignition key is turned to the ACC or LOCK position, if the
front doors are not opened.
 DOOR LOCK CONTROL SYSTEM
The door lock control system with 2±step unlock function is standard on the LE and XLE grade model and optional
as a set with the power window system on the CE grade model. With the 2±step function, turning the key once in
the driver's door unlocks the driver's door only. Turning it twice unlocks all the doors.
A key confinement prevention function is provided. When the door is opened and the door lock button is locked
with the key still inserted in the ignition key cylinder, the key confinement prevention mechanism immediately
turns the door lock button to unlock. This prevents the key from being inadvertently locked inside the vehicle.

24
INTERIOR
 KEY REMINDER SYSTEM
All vehicles have a key reminder system as standard equipment. When the ignition key is left inserted in the ignition
key cylinder at ACC or LOCK positioon and the driver's door is opened, this system sounds a warning tone to remind
the driver to remove the ignition key.
 SRS AIRBAG
For all models, the new Camry has as standard equipment a driver's airbag in the steering wheel pad and a front
passenger airbag located in the instrument panel above the glove box.
 CRUISE CONTROL SYSTEM
The cruise control system is standard equipment on the LE and XLE grade model and an option on the CE grade
models. The main switch and control switch are on the a single lever, which is installed on the steering wheel and
can be operated easily.
 ILLUMINATED ENTRY SYSTEM
An illuminated entry system is standard equipment on the LE and XLE models. This system makes it easy to let
the Camry in and out at night, etc.
On the LE grade model, the ignition key cylinder illumination is turned on automatically when the door is opened.
When the door is closed, the ignition key cylinder illumination remains on for approximately 5 seconds, then goes
off automatically.
On the XLE grade model, the illuminated entry system turns on the dome light and ignition key cylinder
illumination for approximately 15 seconds after either door is closed when passengers are entering or leaving the
vehicle. While these lights are on for 15 seconds, if the ignition switch is turned to the ACC or ON position, or if
all doors are locked, the dome light and ignition key cylinder illuminatioons go off immediately.

100BODY ELECTRICALÐLIGHTING
BODY ELECTRICAL
LIGHTING

DESCRIPTION
The new Camry has the following features:
Item
Outline
Daytime Running Light System
This system is designed to automatically activate the headlights during the
daytime to keep the car highly visible to other vehicles.
As in the previous model, the headlights are activated by reducing the nor-
mal high beam brightness.
The basic construction and operation are the same as in the previous model.
Light Auto Turn±Off System
When the ignition key is turned from the ON or ACC to LOCK position and
the driver's door is opened with the taillights and headlights turned on, this
system automatically turns them off.
The basic construction and operation are the same as in the previous model.
Light Auto Turn±Off System
This system is useful when entering the vehicle and inserting the ignition key
into the cylinder in the dark.
2 types of this system are used in the new Camry.
In the first type, when the doors are opened, this system turns on the illu-
minations around ignition key cylinder and dome light (only when the con-
trol switch is set to the DOOR position) simultaneously. These lights fade
out in about 15 seconds. However, under certain conditions such as when all
doors are locked, the lights will turn off immediately even if the system is
operating.
The basic construction and operation are the same as in the '97 Avalon.
In the second type, when the door is opened, this system turns on the illu-
minations around the ignition key cylinder. This illumination remains on for
about 5 seconds after the door is closed.

105 BODY ELECTRICALÐACCESSORIES
ACCESSORIES

DESCRIPTION
The new Camry includes the accessory systems shown in the below.
System
Outline
Power Window System
The power window system includes one±touch auto down and key±off opera-
tion functions. The one±touch auto down function automatically opens the
driver 's door window fully. The key±off operation function makes it possible
to operate the power windows for approximately 45 seconds after the igni-
tion key is turned to the ACC or LOCK position, if the front doors are not
opened.
The basic construction and operation of this system are the same as in the
previous model.
Door Lock Control System
This system has a ªkey±linked lock and unlock functionº and a ªkey±confine
prevention functionº. All doors can be locked and unlocked simultaneously
by a key operation at the front right or left foor. (The key needs to be oper-
ated twice to unlock all the doors at the driver's door.) If the door lock opera-
tion is performed when one of the front doors is open and the ignition key is
inserted in the key cylinder, doors are unlocked automatically to prevent the
ignition key from being left inside the vehicle.
The basic construction and operation are the same as in the previous model.
Wireless Door Lock Remote Con-
trol System
A remote control system in which the lock and unlock functions of all doors
and panic alarm function can be controlled by the signals emitted from a
transmitter is adopted. The transmitter is also provided with a 2±step unlock
function to unlock all the doors by pressing the switch twice.
The basic construction and operation are the same as in the '96 Avalon.
However, certain functions have been changed. For details, see page 107.
Theft Deterrent System
When an attempt is made to forcibly enter the vehicle or open the hood or
trunk lid without a key, or when the battery terminals are removed and re-
connected, this system sounds the horn and flashes the headlights and tail-
lights for about 1 minute to alert the owner. At the same time, it locks all the
doors and electronically disconnects the starter.
The basic operation is the same as in the '96 Avalon.
Power Seat
As in the previous model, the front seats are power assisted by electric mo-
tors so that the seat positions can be adjusted easily by a simple switch op-
eration.
The basic construction and operation are the same as in the previous model.

106BODY ELECTRICALÐACCESSORIES
SystemOutline
SRS Airbag
The SRS (Supplemental Restraint System) airbag is provided for the driver
and front passenger. The SRS airbag has been designed to lessen the shock to
the head and chest of the driver and front passenger in the event of a frontal
impact collision as a supplement to the seat belt.
A 1±sensor type airbag system is used in which the detection of decelera-
tion during a collision as well as control of the airbag system is accom-
plished by the airbag sensor assembly.
The basic construction and operation are the same as in the '96 Avalon.
However, the inflator for front passsenger and airbag sensor assembly have
been changed.
For details, see page 111.
Cruise Control System
Once it has been set at a desired vehicle speed, this system automatically
adjusts the engine throttle position to maintain the vehicle speed at the de-
sired speed without operating the acceleration pedal.
The basic construction and operation are the same as in the previous model.
However, in the new model, a new type acutator has been adopted. Also, the
functions of the cruise control ECU has been changed. For details, see page
116.
Moon Roof
The moon roof is a tilt±up and sliding type the same as in the previous mod-
el. This system includes ªkey±off operationº, which is the same as with the
power window system. The new model offers an additional ªone±touch slide
openº function which enables the moon roof to fully open when the slide
switch is pressed toward the opening side for a few seconds.
Electrical Remote Control Mirror
The electrical remote control mirrors used in the previous model are also
used in the new model. Also, the internal heater to remove water drops from
the mirror surface is provided.
Key Reminder System
When the driver's door is opened with the ignition key in the ACC or LOCK
position, this system sounds a buzzer to warn the driver that the ignition key
has not been removed.
The basic construction and operation are the same as in the previous model.

108BODY ELECTRICALÐACCESSORIES
2. Layout of Functional Parts
The major functional parts of the wireless door lock remote control system are whown below.
3. Construction
Transmitter
The transmitter is a key±holder type, which is
separate from the ignition key. the lock and unlock
functions of all doors can be controlled by operating
the switches on the ransmitter. Also, this transmitter
is equipped with a panic switch which activates the
security alarm of the theft deterrent system.

CAMRY ± NEW FEATURES
149EG07
Clamp
Fuel Hose
Fuel Filter 10
Fuel Filter
A quick connector is used to connect the fuel fil-
ter and the fuel hose together to improve seri-
viceability.
6. Engine Control System
General
The California specification automatic transaxle model has adopted an air-fuel sensor. All models are avail-
able with the Engine Immobiliser System as an optional equipment. The models other than the California
specification automatic transaxle model are basically the same as the '97 models except for the adoption
of the Engine Immobiliser System.
SFI (Sequential Multiport Fuel Injection)
The precision of the air-fuel ratio feedback control has been improved through the adoption of the air-fuel
ratio sensor. The operation of the air-fuel ratio sensor and the ECM are the same as those of the California
specification model with the 5S-FE engine and automatic transaxle. For details, see the '97 Camry New Car
Features (Pub. No. NCF134U).
Engine Immobiliser System
The engine immobiliser system has been designed to prevent the vehicle from being stolen. This system
uses an ECM that stores the ID code of the authorized ignition key. If an attempt is made to start the engine
using an unauthorized key, the ECM prohibits fuel delivery and ignition effectively disabling the engine.
For details, see page 23 in the Engine Immobiliser system section.