check engine light TOYOTA CAMRY HYBRID 2007 XV40 / 8.G Owners Manual

’07Camry hybrid_U (L/O 0610)
6
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
Drive your vehicle with smooth accel-
eration and deceleration.
While driving, energy is recovered
through the regenerative brake as the
vehicle decelerates. However, for effi-
cient use, do not accelerate or deceler-
ate your vehicle more than necessary.
Avoid abrupt acceleration and decelera-
tion.
The power of the hybrid battery can be
checked on the multi−information dis-
play or the navigation system screen
(with navigation system). See “—Hybrid
battery status” on page 5 for details.
Gradual or non −abrupt acceleration and
deceleration will make more effectively
use of the traction motor without hav-
ing to use engine power. When parking, be sure to put the trans-
mission into the “P” position. While
driving, put the transmission into the
“D” position.
In the “N” position, the engine operates
but electricity cannot be generated. The
hybrid battery will be discharged requir-
ing unnecessary engine power to re-
charge.
The hybrid system automatically re-
charges the hybrid battery when the
remaining battery power is reduced.
However, the hybrid battery cannot be
recharged if the transmission is in the
“N” position.
For detailed information, see “How to save
fuel and make your vehicle last longer” on
page 311 in Section 3.
INFORMATION
The engine starts and stops automati-
cally. (It stops during a low load driv-
ing, deceleration or when the vehicle
is stopped.)
As long as the “READY” light remains
on, you can start your vehicle using
the traction motor even with the en-
gine stopped.
The engine may not stop automatical-
ly in the following conditions:
 During engine warmup
 During hybrid battery charging
 During low or high hybrid battery
temperature
Efficient use of your hybrid
vehicle

’07Camry hybrid_U (L/O 0610)
143
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
MessageStatusAction
qSteering lock is stuck.Turn steering wheel slightly.
rOil change is nearly due.Check engine oil.
sOil change is due.Change engine oil.
tWasher fluid level is low.Add washer fluid.
uMoon roof is opened with “POWER” switch turned off.Close moon roof.
vFuel door is left open.Close the fuel door.

’07Camry hybrid_U (L/O 0610)
302
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
The engine may not start even with the
“READY” light on.
If there is a problem somewhere in the
hybrid system, the message “CHECK
HYBRID SYSTEM” will appear on the
multi−information display. Have your
vehicle checked by your Toyota dealer as
soon as possible.
If the hybrid system will not start...
In the following cases, the hybrid system
will not start.
If a buzzer sounds from the vehicle,
and the message “KEY IS NOT
DETECTED” appears on the multi −infor-
mation display and the master warning
light comes on when pressing the
“POWER” switch, this indicates that the
key is not in the vehicle.
If the key is placed in the trunk, the
hybrid system cannot be started.
There are instances in which the hybrid
system will not start, even if the key
is in the vehicle (e.g. on the floor, in
the cup holder or glove box).
When the push button start function
does not operate properly, the following
may be causes:
The key battery may be discharged if
the electronic key does not work.
You can start the hybrid system by
touching the Toyota logo side of the
electronic key to the “POWER” switch.
For details, see “Smart key system” on
page 32 in Section 1 −2.
Replace the key battery as soon as
possible. (See “—Replacing battery” on
page 30 in Section 1 −2.)
The hybrid system was repeatedly
turned on and off over a short period.
Wait 10 seconds and then start the
hybrid system.

’07Camry hybrid_U (L/O 0610)
305
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
If the warning light is still lit when the key
is in the vehicle, the key battery is dis-
charged. Check that the indicator light on
the key comes on by pushing the lock
button on the key. When the indicator light
does not come on, change the key battery
so that smart key system works properly.
(B) A warning buzzer sounds once fromthe instrument cluster, accompanied
by three warning sounds from the
vehicle when the driver gets out of
the vehicle and closes the door.
This indicates that the driver is attempting
to leave the vehicle carrying the key with
“POWER” switch turned off although the
transmission selector lever has been set
in the “P” position. The message “KEY IS
NOT DETECTED” will also appear on the
multi −information display and the master
warning light will come on.
Get out of the vehicle only after turning
off the hybrid system by pressing the
“POWER” switch and checking that the
indicator light on the “POWER” switch has
gone off. If the driver returns to the ve-
hicle without carrying the key and begins
driving, a warning buzzer will sound once
more. (C) A warning buzzer sounds from the
vehicle for two seconds after locking
the door with the door handle
switch.
This indicates that the driver is attempting
to lock the doors while carrying the key,
neglecting to follow the instructions for
case (B) above.
Lock the doors only after turning off the
hybrid system by pressing the “POWER”
switch and checking that the indicator light
on the “POWER” switch has gone off.
A warning buzzer that sounds even though
the engine has been turned off indicates
that driver is attempting to lock the ve-
hicle with the keys still in the vehicle.
Leave the vehicle only after making sure
that you are carrying the key. (D) A warning buzzer sounds continu-
ously from the instrument cluster
when opening the driver ’s door.
This indicates that the transmission selec-
tor lever is in a position other than “P”
and that the “POWER” switch is not
turned off. The message “SHIFT TO P
RANGE” will also appear on the multi −in-
formation display.
Get out of the vehicle only after setting
the transmission selector lever in the “P”
position, turning off the hybrid system by
pressing the “POWER” switch and
checking that the indicator light on the
“POWER” switch has gone off.

’07Camry hybrid_U (L/O 0610)
306
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
(E) A warning buzzer sounds continu-ously from the instrument cluster
and from the vehicle when closing
the door after getting out of the ve-
hicle.
This indicates that the driver is attempting
to leave the vehicle carrying the key, ne-
glecting to follow the instructions for case
(D) above. The messages, “SHIFT TO P
RANGE” and “KEY IS NOT DETECTED”,
will also appear alternately on the multi −
information display and the master warn-
ing light will come on.
Get out of the vehicle only after setting
the transmission selector lever in the “P”
position, turning off the hybrid system by
pressing the “POWER” switch and
checking that the indicator light on the
“POWER” switch has gone off. (F) A warning buzzer sounds once from
the instrument cluster and three
times from the vehicle when a pas-
senger is getting out of the vehicle.
This indicates that the passenger is
attempting to leave the vehicle carrying
the key, without turning the hybrid system
off. The message “KEY IS NOT
DETECTED” will also appear on the
multi −information display and the master
warning light will come on.
When passengers get out of the vehicle,
care should be taken to leave the key
with the driver. If the driver begins driving
after a passenger gets out of the vehicle
carrying the key, a warning buzzer will
sound once more.
(G) A warning buzzer sounds from the vehicle for two seconds when lock-
ing the vehicle from the outside with
the door handle switch.
This indicates that the driver is attempting
to lock the door with the key still in the
vehicle.
Leave the vehicle only after making sure
that you are carrying the key. (H) A warning buzzer sounds once from
the instrument cluster when the
“POWER” switch is turned off.
This indicates that the key battery is low.
(This warning buzzer sounds only when
the hybrid system has been on or the
“POWER” switch has been set at ON for
20 minutes or more.) The message “LOW
KEY BATTERY” will also appear on the
multi −information display.
Change the key battery ahead of time in
order to ensure that the smart key system
works properly.
(I) A warning buzzer sounds repeatedly from the instrument cluster when
opening the driver ’s door with the
“POWER” switch turned off.
This indicates that the steering wheel is
not locked. Turn the engine off and then
open the door in order to lock the steering
wheel.

’07Camry hybrid_U (L/O 0610)
307
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
(J) The “POWER” switch flashes greenonce every second.
This indicates that the steering lock is
stuck. The message “S/T IS NOT
UNLOCKED” will also appear on the
multi −information display.
To free it, rotate the steering wheel slight-
ly while pressing the “POWER” switch.
(K) The “POWER” switch flashes amber once every 2 seconds.
When the message “CHECK S/T LOCK”
appears on the multi −information display—
This indicates a problem with the steering
lock function. Have your vehicle checked
at your Toyota dealer.
When no message appears on the multi −
information display—
This indicates a problem with the push
button start function. Have your vehicle
checked at your Toyota dealer. THEFT PREVENTION FUNCTION
When the hybrid system is turned off,
the engine immobilizer system is auto-
matically set. (See “Engine immobilizer
system” on page 24 in Section 1
−2.)
When the driver ’s door is opened after
turning off the hybrid system, the steer-
ing wheel will lock.
When the 12 volt battery is discharged,
the steering lock function may not op-
erate properly.
Always slow down in gusty crosswinds.
This will allow you much better control.
Drive slowly onto curbs and, if pos-
sible, at a right angle. Avoid driving
onto high, sharp− edged objects and
other road hazards. Failure to do so
can lead to severe tire damage such
as a tire burst.
Drive slowly when passing over bumps
or travelling on a bumpy road. Other-
wise, the impact could cause severe
damage to the tires and/or wheels.
When parking on a hill, turn the front
wheels until they touch the curb so
that the vehicle will not roll. Apply the
parking brake, and place the transmis-
sion in “P”. If necessary, block the
wheels.
Tips for driving in various
conditions

’07Camry hybrid_U (L/O 0610)
308
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
Washing your vehicle or driving through
deep water may get the brakes wet. To
see whether they are wet, check that
there is no traffic near you, and then
press the pedal lightly. If you do not
feel a normal braking force, the brakes
are probably wet. To dry them, drive
the vehicle cautiously while lightly
pressing the brake pedal with the park-
ing brake applied. If they still do not
work safely, pull to the side of the road
and call a Toyota dealer for assistance.
CAUTION
Before driving off, make sure that
the parking brake is fully released
and the parking brake reminder
light is off.
Do not leave your vehicle unat-
tended while the hybrid system is
operating.
Do not rest your foot on the brake
pedal while driving. It can cause
dangerous overheating, needless
wear, and poor fuel economy.
To drive down a long or steep hill,
reduce your speed and use engine
brake. Remember, if you ride the
brakes excessively, they may over-
heat and not work properly.
Be careful when accelerating, en-
gine braking or braking on a slip-
pery surface. Sudden acceleration
or engine braking could cause the
vehicle to skid or spin.
Do not drive in excess of the speed
limit. Even if the legal speed limit
permits it, do not drive over 140
km/h (85 mph) unless your vehicle
has highspeed capability tires.
Driving over 140 km/h (85 mph) may
result in tire failure, loss of control
and possible injury. Be sure to con-
sult a tire dealer to determine
whether the tires on your vehicle
are highspeed capability tires or
not before driving at such speeds.
Do not continue normal driving
when the brakes are wet. If they are
wet, your vehicle will require a
longer stopping distance, and it
may pull to one side when the
brakes are applied. Also, the park-
ing brake will not hold the vehicle
securely.

’07Camry hybrid_U (L/O 0610)
335
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
2. Wash with a mild car−wash soap,
mixed according to the manufacturer ’s
instructions. Use a soft cotton mitt and
keep it wet by dipping it frequently into
the wash water. Do not rub hard—let
the soap and water remove the dirt.
Fuel filler door: Do not apply water (high −
pressure car wash, for example) at or
near the fuel tank inlet with the fuel filler
door opened. If the water enters the air
vent, you may experience trouble with re-
fueling or rough engine idling.
Plastic wheel ornaments: The plastic
wheel ornaments are damaged easily by
organic substances. If any organic sub-
stances splash an ornament, be sure to
wash them off with water and check if the
ornament is damaged.
Aluminum wheels: Use only a mild soap
or neutral detergent.
Plastic bumpers: Wash carefully. Do not
scrub with abrasive cleaners. The bumper
faces are soft.
Exterior lights: Wash carefully. Do not use
organic substances or scrub them with a
hard brush. This may damage the sur-
faces of the lights. Road tar: Remove with turpentine or
cleaners that are marked safe for painted
surfaces.
3. Rinse thoroughly—dried soap can cause streaking. In hot weather you
may need to rinse each section right
after you wash it.
4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not
rub or press hard—you might scratch
the paint.
NOTICE
Do not use organic substances
(gasoline, kerosene, benzine or
strong solvents), which may be tox-
ic or cause damage.
 Do not scrub any part of the ve-
hicle with a hard brush, which may
cause damage.
Automatic car wash
Your vehicle may be washed in an auto-
matic car wash, but remember that the
paint can be scratched by some types of
brushes, unfiltered washing water, or the
washing process itself. Scratching reduces
paint durability and gloss, especially on
darker colors. The manager of the car
wash should be able to advise you wheth-
er the process is safe for the paint on
your vehicle.
Waxing your Toyota
Polishing and waxing is recommended
to maintain the original beauty of your
Toyota’s finish.
Apply wax once a month or if the vehicle
surface does not repel water well.
1. Always wash and dry the vehicle be- fore you begin waxing, even if you are
using a combined cleaner and wax.
2. Use a good quality polish and wax. If the finish has become extremely weath-
ered, use a car −cleaning polish, fol-
lowed by a separate wax. Carefully fol-
low the manufacturer ’s instructions and
precautions. Be sure to polish and wax
the chrome trim as well as the paint.

’07Camry hybrid_U (L/O 0610)
343
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
Exhaust system
If you notice any change in the sound of
the exhaust or smell exhaust fumes, have
the cause located and corrected immedi-
ately. See “Engine exhaust cautions” on
page 278 in Section 2.
IN THE TRUNK
12 volt battery condition
See page 369 in Section 7−3 for addition-
al information.
INSIDE THE VEHICLE
Items listed below should be checked
regularly, e.g. while performing periodic
services, cleaning the vehicle, etc.
Lights
Make sure the headlights, stop lights, tail
lights, turn signal lights, and other lights
are all working. Check headlight aim.
Service reminder indicators and warning
buzzers
Check that all service reminder indicators
and warning buzzers function properly.
Steering wheel
Be alert for changes in steering condition,
such as hard steering or strange noise. Seats
Check that all front seat controls such as
seat adjusters, seatback recliner, etc. op-
erate smoothly and that all latches lock
securely in any position. Check that the
head restraints move up and down
smoothly and that the locks hold securely
in any latched position. For folding
−down
rear seatbacks, check that the latches
lock securely.
Seat belts
Check that the seat belt system such as
buckles, retractors and anchors operate
properly and smoothly. Make sure that the
belt webbings not cut, frayed, worn or
damaged.
Accelerator pedal
Check the pedal for smooth operation and
uneven pedal effort or catching.
Brake pedal
Check the pedal for smooth operation and
that the pedal has the proper clearance.
Check the brake booster function.
Brakes
In a safe place, check that the brakes do
not pull to one side when applied. Parking brake
Check that the pedal has the proper travel
and that, on a safe incline, your vehicle
is held securely with only the parking
brake applied.
Transmission “Park” mechanism
Check the lock release button of the se-
lector lever for proper and smooth opera-
tion. On a safe incline, check that your
vehicle is held securely with the selector
lever in “P” position and all brakes re-
leased.
OUTSIDE THE VEHICLE
Items listed below should be performed
from time to time, unless otherwise
specified.
Fluid leaks
Check underneath for leaking fuel, oil, wa-
ter or other fluid after the vehicle has
been parked for a while. If you smell fuel
fumes or notice any leak, have the cause
found and corrected immediately.
Doors and engine hood
Check that all doors including trunk lid
operate smoothly and all latches lock se-
curely. Make sure the engine hood sec-
ondary latch secures the hood from open-
ing when the primary latch is released.

’07Camry hybrid_U (L/O 0610)
355
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
Low level Full level
Add oil O.K. Too full
With the hybrid system at operating
temperature and turned off, check the
oil level on the dipstick. 1. To get a correct reading, the vehicle should be on level ground. After turning
off the hybrid system, wait a few min-
utes for the oil to drain back into the
bottom of the engine.
2. Pull the dipstick out, hold a rag under the end and wipe it clean.
3. Reinsert the dipstick—push it in as far as it will go, or the reading will not be
correct.
4. Pull the dipstick out and look at the oil level while holding a rag under the
end.
CAUTION
Be careful not to touch the hot ex-
haust manifold.
NOTICE
Be careful not to drop engine oil on
the vehicle components.
If the oil level is below or only slightly
above the low level line, add engine oil
of the same type as already in the en-
gine.
Remove the oil filler cap and add engine
oil in small quantities at a time, checking
the dipstick. We recommend that you use
a funnel when adding oil.
The approximate quantity of oil needed to
raise the level between low and full on the
dipstick is indicated as follows:
1.1L(1.2qt.,1.0Imp.qt.)
For the engine oil capacity, see “Service
specifications” on page 382 in Section 8.
When the level reaches within the correct
range, install the filler cap hand− tight.
NOTICE
Be careful not to spill engine oil on
the vehicle components.
 Avoid overfilling, or the engine
could be damaged.
 Check the oil level on the dipstick
once again after adding the oil.
Checking the engine oil level