engine oil capacity TOYOTA CAMRY V20 1986 Service Information

C. (4WD M/T (3S±FE))
Replace transaxle (incl. transfer) oil
(a) Remove the engine under cover.
(b) Remove the filler and drain plugs, and drain the oil.
(c) Reinstall the drain plug securely.
(d) Add new oil until it begins to run out of the filler hole.
Transaxle oil: Transaxle oil E50 (08885±80206) or equiv-
alent
Recommended transaxle oil:
Oil grade API GL±5
Viscosity SAE 75w±90 or 80W±90
Above ±18
°C (0°F) SAE 90
Below ±18°C (0°F) SAE 80W
Capacity: 5.0 liters (5.3 US qts, 4.4 Imp. qts)
(e) Reinstall the filler plug securely.
(f) Reinstall the engine under cover.
(d) with the engine OFF, add new fluid through the
dipstick tube.
Transmission fluid: ATF DEXRON
II
Drain and refill capacity: 2.5 liters
(2.6 us qts, 2.2 Imp. qts)
(e) Start the engine and shift the selector into all posi-
tions from ºf'º through ºLº, and then shift into ºPº.
(f) With the engine idling, check the fluid level. Add
fluid up to the ºCOOLº level on the dipstick.
NOTICE: Do not overfill. The transmission and differ-
ential are separate units.
(g) Recheck the fluid level with the normal tempera-
ture (70 ± 80
°C (158 ± 176°F)) and add as neces-
sary.
(h) Reinstall the engine under cover. D. (2WD A/T)
Replace transaxle fluid
(Transmission)
(a) Remove the engine under cover.
(b) Using a 10 mm hexagon wrench, remove the drain
plug and drain the fluid.
(e) Reinstall the drain plug securely.
± MAINTENANCEMaintenance OperationsMA±12

G. (4WD)
Replace rear differential oil
(a) Remove the filler and drain plugs, and drain the oil.
(b) Reinstall the drain plug securely.
(c) Add new oil until it beings to run out of the filler hole.
Rear differential oil:
Oil grade API GL±5 hypoid gear oil
Viscosity Above ±18°C (0°F) SAE 90
Below ±18°C (0°F) SAE 80W±90
Capacity: 1.1 liters (1.2 U S qts, 1.0 Imp. qts)
(d) Reinstall the filler plug securely.
22. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
Tighten the following parts:
wFront seats mount bolts
Torque: 375 kg±cm (27 ft±Ib, 37 N±m)
(d) Add new oil through the dipstick tube.
Transaxle oil: Transaxle oil E50 (08885±80206) or
equivalent
Recommended transaxle oil:
Oil grade API GL±5
Viscosity SAE 75W±90 or 80w±90
Above ±18°C (0°F) SAE 90
Below ±18°C (0°F) SAE 80W
Capacity: 0.7 liters (0.74 US qts, 0.62 Imp. qts)
F. (4WD A/T)
Replace transfer oil
(a) Remove the engine under cover.
(b) Using a 10 mm hexagon wrench, remove the drain plug
and drain the oil.
(c) Reinstall the drain plug securely.
(e) Check the oil level and add as neces-
sary.
M Reinstall the engine under cover.
± MAINTENANCEMaintenance OperationsMA±14

REPLACEMENT OF TRANSAXLE GEAR OIL
1. DRAIN TRANSAXLE OIL
2. FILL TRANSAXLE OIL WITH GEAR OIL
Oil: Transaxle oil E50 (08885±80206) or equivalent
Recommended oil
Oil grade: API G!±5
Viscosity: SAE 75W±90 or 80W±90
Above ±18°C (0°F) SAE 90
Below ±18°C (0°F) SAE 80W
Capacity: 5.0 liters (5.3 US qts, 4.4 Imp qts)
(MAIN POINT OF REMOVAL AND
INSTALLATION)
1. REMOVE TRANSAXLE ASSEMBLY
HINT: When removing transaxle from engine, remove as the
following procedure since cylinder block rib contacts
transfer case.
(a) Pull straight until there are space of 60 ± 80mm (2 ±3 in.)
between engine and transaxle case.
(e) While holding the transfer output slightly, pull out
whole transaxle.
2. INSTALL TRANSAXLE ASSEMBLY FOLLOWING
REMOVAL SEQUENCE IN REVERSE(b) Move the transmission case cover to the arrow in the
illustration.
± MANUAL TRANSAXLERemoval and Installation of TransaxleMT±117

Front and rear brake
Pad thickness
Disc thickness
Disc runout
Parking brake
Lining thickness
Drum inside diameter
Front axle and suspension
Ball joint vertical play
Steering wheel freeplay
Torque specifications
Front seat mount bolts
Strut/stabilizer bar bracket x Body
Engine mounting center member x Body
Front suspension lower crossmember x Body
Rear suspension lower crossmember x Body
MAINTENANCE
Engine
Engine oil capacity (Drain and refill with oil fitter change)
Gap
Firing order
Valve clearance Coolant capacity 1w/ Heater) Drive belt tension
Alternator
Spark plug
Type
Chassis
PS pump
± SERVICE SPECIFICATIONSMaintenanceA±2

Engine coolant x Drain plug
Water pump x Water pump cover
Water pump x Cylinder head
Water by±pass pipe X Water pump
Water inlet housing x Water pump
Oil cooler x Radiator tower tank
Cylinder block x Drain plug
Water pump x Cylinder block
Water inlet x Water pump
Water inlet pipe x Alternator belt adjusting bar
LUBRICATION SYSTEM (3S±FE)
SpecificationsTorque Specifi
cations (3S±FE)
COOLING SYSTEM
Specifications
Torque Specifications (2VZ±FE)
Valve opening temperature
Valve lift at 95°C (203°F) Relief valve opening pressure
Engine coolant capacityEngine coolant capacity
at Idling
at 3,040 rpm
STD
Limit
STD
Limit Body clearance .See page A±20 STD
Limit
Part tightened
Part tightenedSee page A±2
Tip clearance3S±FE
2VZ±FE
Oil pressureThermostat
Oil pumpRadiator
± SERVICE SPECIFICATIONSCooling SystemA±17

Engine coolant x Drain plug
Water pump x Water pump cover
Water pump x Cylinder head
Water by±pass pipe X Water pump
Water inlet housing x Water pump
Oil cooler x Radiator tower tank
Cylinder block x Drain plug
Water pump x Cylinder block
Water inlet x Water pump
Water inlet pipe x Alternator belt adjusting bar
LUBRICATION SYSTEM (3S±FE)
SpecificationsTorque Specifi
cations (3S±FE)
COOLING SYSTEM
Specifications
Torque Specifications (2VZ±FE)
Valve opening temperature
Valve lift at 95°C (203°F) Relief valve opening pressure
Engine coolant capacityEngine coolant capacity
at Idling
at 3,040 rpm
STD
Limit
STD
Limit Body clearance .See page A±20 STD
Limit
Part tightened
Part tightenedSee page A±2
Tip clearance3S±FE
2VZ±FE
Oil pressureThermostat
Oil pumpRadiator
± SERVICE SPECIFICATIONSLubrication System (3S±FE)A±17

Engine oil drain plug
Oil pump body cover x Oil pump body
Oil pump x Cylinder block
Oil strainer x Cylinder block
Oil strainer x Oil pump
Oil pan x Cylinder block
Oil pan x Oil pump
Stiffener plate x Cylinder block
Stiffener plate x Transaxle case
Oil pan x Drain plug
Oil pump. x Cylinder block
Oil strainer x Main bearing cap
Oil strainer x Oil pump
Oil pan x Cylinder block
Oil pan x Oil pump
Oil pan X Rear oil seal retainer
Stiffener plate x Cylinder block
Stiffener plate x Transaxle case
LUBRICATION SYSTEM (2VZ±FE)
Specifications
Torque SpecificationsTorque Specifications
Engine coolant capacity
Body clearanceSee page A±20
Part tightened Side clearancePart tightened
Tip clearance Oil pressure
Oil pump
± SERVICE SPECIFICATIONSLubrication System (3S±FE)A±18

Engine oil drain plug
Oil pump body cover x Oil pump body
Oil pump x Cylinder block
Oil strainer x Cylinder block
Oil strainer x Oil pump
Oil pan x Cylinder block
Oil pan x Oil pump
Stiffener plate x Cylinder block
Stiffener plate x Transaxle case
Oil pan x Drain plug
Oil pump. x Cylinder block
Oil strainer x Main bearing cap
Oil strainer x Oil pump
Oil pan x Cylinder block
Oil pan x Oil pump
Oil pan X Rear oil seal retainer
Stiffener plate x Cylinder block
Stiffener plate x Transaxle case
LUBRICATION SYSTEM (2VZ±FE)
Specifications
Torque SpecificationsTorque Specifications
Engine coolant capacity
Body clearanceSee page A±20
Part tightened Side clearancePart tightened
Tip clearance Oil pressure
Oil pump
± SERVICE SPECIFICATIONSLubrication System (2VZ±FE)A±18