oil viscosity TOYOTA CAMRY V20 1986 Service Information

REPLACEMENT OF TRANSAXLE GEAR OIL
1. DRAIN TRANSAXLE OIL
2. FILL TRANSAXLE OIL WITH GEAR OIL
Oil: Transaxle oil E50 (08885±80206) or equivalent
Recommended oil
Oil grade: API G!±5
Viscosity: SAE 75W±90 or 80W±90
Above ±18°C (0°F) SAE 90
Below ±18°C (0°F) SAE 80W
Capacity: 5.0 liters (5.3 US qts, 4.4 Imp qts)
(MAIN POINT OF REMOVAL AND
INSTALLATION)
1. REMOVE TRANSAXLE ASSEMBLY
HINT: When removing transaxle from engine, remove as the
following procedure since cylinder block rib contacts
transfer case.
(a) Pull straight until there are space of 60 ± 80mm (2 ±3 in.)
between engine and transaxle case.
(e) While holding the transfer output slightly, pull out
whole transaxle.
2. INSTALL TRANSAXLE ASSEMBLY FOLLOWING
REMOVAL SEQUENCE IN REVERSE(b) Move the transmission case cover to the arrow in the
illustration.
± MANUAL TRANSAXLERemoval and Installation of TransaxleMT±117

11. CONNECT PROPELLER SHAFT
(a) Align the matchmarks on the flanges and connect the
propeller shaft with the four bolts, washers and nuts.
(b) Torque the bolts and nuts.
Torque: 760 kg±cm (54 ft±Ib, 74 N±m)
13. CHECK OIL LEVEL
Oil grade: AN GL±5 hypoid gear oil
Viscosity: Above ± 18
°C (0°F) SAE 90
Below ± 18°C (0°F) SAE 80 W ± 90
Capacity: 1.1 liters (1.2 US qts, 1.0 Imp.qts)
12. INSTALL REAR CROSSMEMBER
Torque: 730 kg±cm (53 ft±Ib, 72 N±m)
10. STAKE DRIVE PINION NUT
± REAR AXLE AND SUSPENSIONDifferential (4WD)RA±30

5. FILL DIFFERENTIAL WITH GEAR OIL
(a) Install the drain plug with new gasket.
Torque: 500 kg±cm (36 ft±Ib, 49 N±m)
(b) Fill the differential with gear oil.
Oil grade: API GL±5 hypoid gear oil
Viscosity: Above ±18
°C (0°F) SAE 90
Below ±18°C
(0°F) SAE 80W±90
Capacity: 1.1 liters (1.2 US qts, 1.0 lmp.qts)
(c) Install the filler plug with new gasket.
Torque: 400 kg±cm (29 ft±lb, 39 N±m)
INSTALLATION OF DIFFERENTIAL
(See page RA±27)
1. INSTALL DIFFERENTIAL
(a) Position the differential and torque the four bolts and nuts.
Torque: 970 kg±cm (70 ft±Ib. 95 N±m)
2. CONNECT PROPELLER SHAFT
(a) Align the matchmarks on the flanges and connect the
flanges with four bolts, nuts and washers.
(b) Torque the four bolts and nuts.
Torque: 750 kg±cm (54 ft±lb, 74 N±m)
4. CONNECT DRIVE SHAFTS (See page RA±131) (b) Install and torque the two bolts.
Torque: 1,500 kg±cm 108 ft±lb, 147 N±m)
± REAR AXLE AND SUSPENSIONDifferential (4WD)RA±49

Dry fill 3S±FE
2VZ± FE
Drain and refill
w/ Oil filter changeAPI grade SG, multigrade,
recommended viscosity and fuel±efficient oil
w/o Oil filter change Engine oil
LUBRICANT
Classification Ca pa city
Imp. qts
US qts Liters Item
± SERVICE SPECIFICATIONSLubricantA±20

Transaxle oil E50 (08885±80206) or
equivalent
Recommended oil
Oil grade: AN GL±5
Viscosity : SAE 75W±90 or 80W±90
SA E 90W
[above ±18°C (0°F)]
SAE 80W
[below ±18°C (0°F)]
Transaxle oil E50 (08885±80206) or
equivalent
Recommended oil
Oil grade: API GL±5
Viscosity : SAE 75W±90 or 80W±90
SAE 90W
[above ±18°C (0°F)]
SAE 80W
[below ±18°C (0°F)]
API grade GL±5
Hypoid gear oil
Viscosity: Above ±18°C (0°F) SAE 90
Below ±18°C (0°F) SAE 80W±90 Differential oil
(w/ Automatic transaxle)
SV21 series
VZV21 series
Molybdenum disulphide lithium base,
NLGI No. 2 Automatic transaxle
fluid
(w/o Differential oil)
ATF type T (08886±00405) or equivalent Al 40E
Dry fill
Drain and refill Al 40L
Dry fill
Drain and refill
A540H
Dry fill
Drain and refillA540E
Dry fill
Drain and refill E56F5
(w/ Differential and
transfer)
API GL±4 or GL±5
SAE 75W±90 or 80W±90
Lithium base multipurpose, NLGI No. 2
SAE J 1703 or FMVSS No. 116, DQT3 S51
(w/ Differential oil)
Steering gear housing grease
Manual
transaxle oil
Wheel bearing greaseTransfer oil (A540H)
Power steering fluid
LUBRICANT
800cc 48.8 cu in. Rear differential oilATF DEXRON II ATF DEXRON
11Classification
Brake fluidCapacity
Imp. qts
US qts Liters
Item
E52
ATF DEXRON II
ATF DEXRON II
± SERVICE SPECIFICATIONSLubricantA±42