power steering TOYOTA COROLLA 1996 User Guide

Part 7Checking the engine oil level
155
DO-IT-YOURSELF
MAINTENANCEÐ
Chapter 7-2
Engine and Chassis
Checking the engine oil level
Checking the engine coolant
level
Checking brake fluid
Checking power steering fluid
Checking tire pressure
Checking and replacing tires
Rotating tires
Installing snow tires and chains
Replacing wheels
Aluminum wheel precautions
With the engine at operating tempera-
ture and turned off, check the oil level
on the dipstick.
1. To get a true reading, the vehicle
should be on a level spot. After turning off
the engine, wait a few minutes for the oil
to drain back into the bottom of the en-
gine.
2. Pull out the dipstick, and wipe it clean
with a rag.
3. Reinsert the dipstick'push it in as far
as it will go, or the reading will not be cor-
rect.
4. Pull the dipstick out and look at the oil
level on the end.If the oil level is below or only slightly
above the low level line, add engine oil
of the same type as already in the en-
gine.
Remove the oil filter cap and add engine
oil in small quantities at a time, checking
the dipstick.
The approximate quantity of oil needed to
fill between the low level line and the full
level line on the dipstick is indicated below
for reference.
When the level reaches within the correct
range, install the filler cap hand-tight.
Oil quantity, L (qt., Imp. qt.):
4A-FE engine 1.0 (1.1, 0.9)
7A-FE engine 1.2 (1.3, 1.1)
NOTICE
Avoid overfilling, or the engine
could be damaged.
Check the oil level on the dipstick
once again after adding the oil.
ProCarManuals.com

158If the level is low, add SAE J1703 or
FMVSS No. 116 DOT 3 brake fluid to the
brake reservoir.
Remove and replace the reservoir covers
by hand. Fill the brake fluid to the dotted
line. This brings the fluid to the correct lev-
el when you put the cover back on.
Use only newly opened brake fluid. Once
opened, brake fluid absorbs moisture
from the air, and excess moisture can
cause a dangerous loss of braking.
CAUTION!
Take care when filling the reservoir
because brake fluid can harm your
eyes and damage painted surfaces.
If fluid gets in your eyes, flush your
eyes with clean water.
If you spill the fluid, be sure to wash
it off with water to prevent it from
damaging the parts or paint.
NOTICE
Check the fluid level on the dipstick. If
necessary, add automatic transmis-
sion fluid DEXRON
[-II or-III.
If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little more
in frigid temperatures), the fluid is hot
(60C'80C or 140F'175F). You
may also check the level when the fluid is
cold (about room temperature,
10C'30C or 50F'85F) if the engine
has not been run for about five hours.
a. Clean all dirt from outside of the reser-
voir tank.
b. Remove the filler cap by turning it
counterclockwise and wipe the dipstick
clean.c. Reinstall the filler cap.
d. Remove the filler cap again and look at
the fluid level. If the fluid is cold, the level
should be in the COLDº range on the dip-
stick. Similarly, if it is hot, the fluid level
should be in the HOTº range. If the level
is at the low side of either range, add auto-
matic transmission fluid DEXRON

-II or
-III to bring the level within the range.
e. After replacing the filler cap, visually
check the steering box case, vane pump
and hose connections for leaks or damage.
CAUTION!
The reservoir tank may be hot so be
careful not to burn yourself.
Avoid overfilling, or the power
steering could be damaged.
NOTICE
Checking power steering fluid
ProCarManuals.com

182 Model:
4A-FE and 7A-FE
Type:
4 cylinder in line, 4 cycle, gasoline
Bore and stroke, mm (in.):
4A-FE engine
81.0 x 77.0 (3.19 x 3.03)
7A-FE engine
81.0 x 85.5 (3.19 x 3.37)
Displacement, cm
3 (cu. in.):
4A-FE engine 1587 (96.8)
7A-FE engine 1762 (107.5)Fuel type:
Unleaded fuel, Research Octane Num-
ber 91 (Octane Rating 87) or higher
Fuel tank capacity, L (gal., Imp. gal.):
50 (13.2, 11.0)ENGINE
Valve clearance (engine cold), mm (in.):
Intake 0.15'0.25 (0.006'0.010)
Exhaust 0.25'0.35 (0.010'0.014)
Spark plug type:
NIPPONDENSO K16R-U
NGK BKR5EYA
Spark plug gap, mm (in.):
0.8 (0.031)
Drive belt tension measured with Borroughs
drive belt tension gauge No. BT- 33- 73F
(used belt), Ibf:
Generator belt 115 + 20
Air conditioning
compressor belt 100 + 20
Power steering
pump belt 80 + 20
ENGINE LUBRICATION
Oil capacity (drain and refill), L (qt., Imp.
qt.):
4A-FE engine
With filter 3.0 (3.2, 2.6)
Without filter 2.8 (3.0, 2.5)
7A-FE engine
With filter 3.7 (3.9, 3.3)
Without filter 3.5 (3.7, 3.1)
Fuel Service specifications Engine
ProCarManuals.com

184 DIFFERENTIAL
(3- speed type automatic transmission)
Fluid capacity, L (qt., Imp. qt.):
1.4 (1.5, 1.2)
Fluid type:
Automatic transmission fluid DEX-
RON
[II
BRAKES
Minimum pedal clearance when de-
pressed, with the pressure of 490 N (50 kgf,
110 lbf) with the engine running, mm (in.):
70 (2.8)
Pedal freeplay, mm (in.):
1Ð6 (0.04Ð0.24)
Pad wear limit, mm (in.):
1.0 (0.04)
Lining wear limit, mm (in.):
1.0 (0.04)
Parking brake adjustment when pulled
with the force of 196 N (20 kgf, 44 lbf):
4Ð7 clicks
Fluid type:
SAE J1703 or FMVSS No. 116 DOT 3
STEERING
Wheel freeplay:
Less than 30 mm (1.2 in.)
Power steering fluid type:
Automatic transmission fluid DEX-
RON
[-II or-IIITire size:
Spare tire
T115/70D14
T135/70D15
175/65R14 82S
P175/65R14 81S
185/65R14 85S
185/65R14 86S
P185/65R14 85S
Except spare tire
175/65R14 82S
P175/65R14 81S
185/65R14 85S
185/65R14 86S
P185/65R14 85S
Tire pressure, kPa (kgf/cm
2 or bar, psi):
T115/70D14 420 (4.2, 60)
T115/70D15 420 (4.2, 60)
175/65R14 82S 210 (2.1, 30)
P175/65R14 81S 210 (2.1, 30)
185/65R14 85S 210 (2.1, 30)
185/65R14 86S 210 (2.1, 30)
P185/65R14 85S 210 (2.1, 30)Wheel size:
T115/70D14 14 x 4T
T135/70D15 15 x 4T
Other tires 14 x 5.5J
14 x 5.5JJ
Wheel nut torque, NVm (kgfVm, ftVlbf):
103 (10.5, 76)
Tires
ProCarManuals.com