light TOYOTA COROLLA 1996 Owner's Guide

95 If the indicator light flashes, contact your
Toyota dealer as soon as possible. There
may be a slippage of the drive belt or
trouble in the compressor. If this happens,
the air conditioning is automatically turned
off to avoid damage to the drive belt.
(b) Heating
1. Place the temperature control lever
anywhere except the LOW position.
When dehumidified heating is desired,
place the lever between the HIGH and
middle positions.
If cooler air is desired at face level for bi-
level operation, place the lever around the
middle.
2. Move the air intake control lever to the
OUTSIDE AIR position.
If quick circulation of heated air is desired,
move the lever to the RECIRCULATED
AIR position.
For normal use, it is best to keep the lever
in the OUTSIDE AIR position. Otherwise
the windows will fog up more easily.
3. Move the air flow control lever to the
FLOOR position.
If cooler air is desired at face level for bi-
level operation, place the lever to the BI-
LEVEL position.If the windshield fogs up easily, move the
lever to the FLOOR/WINDSHIELD posi-
tion.
For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Move fan speed control lever any-
where except the OFFº position.
5. Leave the air conditioning on-off but-
ton in the ºOFFº position.
If dehumidifed heating is desired, press in
the air conditioning on-off button.
(c) Cooling
1. Place the temperature control lever
anywhere between the middle and LOW
positions.
If warmer air is desired at floor level for bi-
level operation, place the lever around the
middle.
2. Move the air intake control lever to the
OUTSIDE AIR position.
If quick circulation of cooled air is desired,
move the lever to the RECIRCULATED
AIR position.
For normal use, it is best to keep the lever
in the OUTSIDE AIR position.3. Move the air flow control lever to the
FACE position.
If warmer air is desired at floor level for bi-
level operation, place the lever to the BI-
LEVEL position.
For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Move the fan speed control lever any-
where except the OFFº position.
5. Press in the air conditioning on-off but-
ton.
(d) Ventilation
1. Place the temperature control lever at
the LOW position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Move the air flow control lever to the
FACE position.
For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Move the fan speed control lever any-
where except the OFFº position.
5. Leave the air conditioning on-off but-
ton in the OFFº position.ProCarManuals.com

96(e) Windshield defogging and defrost-
ing
To remove interior fog on the windshield:
1. Place the temperature control lever at
any position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Move the air flow control lever to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Move fan speed control lever any-
where except the OFFº position.
5. Press in the air conditioning on-off but-
ton.
To remove frost or exterior fog on the
windshield:
1. Place the temperature control lever at
the HIGH position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Move the air flow control lever to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Move fan speed control lever to the
HIº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.(f) Air flow selection
FACE positionÐThis position directs the
air flow to face level.
BI-LEVELÐThis position directs the air
flow to face level and floor. Except in ven-
tilation, the air to the floor is slightly warm-
er than that to the face level.
FLOOR positionÐThis position directs
the air flow mostly to the floor.
FLOOR / WINDSHIELD position Ð This
position directs the air flow to the wind-
shield and front side windows as well as
the floor.
WINDSHIELD positionÐThis position di-
rects the air flow mostly to the windshield,
front side windows.
Do not use the WINDSHIELD position
during cooling operation in extremely hu-
mid weather. The difference between the
temperature of the outside air and that of
the windshield could cause the outer sur-
face of the windshield to fog up blocking
your vision.
(g) Operating tips

Be sure the air inlet grilles in front of the
windshield are not blocked by leaves
or other obstructions.
If air flow control is not satisfactory,
check the side vents. (See Side
ventsº after Heater controlsº.)

To help cool down the interior after
parking in the hot sun, drive for the first
few minutes with the windows open.
After the excess heat has blown away,
close the windows.

When driving on dusty roads, close all
windows. If dust thrown up by the ve-
hicle is still drawn into the vehicle after
closing the windows, it is recom-
mended that the air intake control le-
ver be set to the OUTSIDE AIR posi-
tion and the fan speed control lever
anywhere except the OFFº position.

If following another vehicle on a dusty
road, or driving in windy and dusty con-
ditions, it is recommened that the air
intake control lever be temporarily set
to the RECIRCULATED AIR position,
which will close off the outside pas-
sage and prevent outside air and dust
from entering the vehicle interior.ProCarManuals.com

99 (b) Heating
1. Place the temperature control lever
anywhere except the NO HEAT position.
If cooler air is desired at face level for bi-
level operation, place the lever around the
middle.
2. Move the air intake control lever to the
OUTSIDE AIR position.
If quick circulation of heated air is desired,
move the lever to the RECIRCULATED
AIR position.
For normal use, it is best to keep the lever
in the OUTSIDE AIR position. Otherwise
the windows will fog up more easily.
3. Move the air flow control lever to the
FLOOR position.
If cooler air is desired at face level for bi-
level operation, move the lever to the BI-
LEVEL position.
If the windshield fogs up easily, move the
lever to the FLOOR/WINDSHIELD posi-
tion.
For detailed information on air flow control
including other settings, see (e) Air flow
selectionº.
4. Move fan speed control lever any-
where except the OFFº position.(c) Ventilation
1. Place the temperature control lever at
the NO HEAT position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Move the air flow control lever to the
FACE position.
For detailed information on air flow control
including other settings, see (e) Air flow
selectionº.
4. Move fan speed control lever any-
where except the OFFº position.
(d) Windshield defogging and defrost-
ing
1. Place the temperature control lever at
FULL HEATING position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Move the air flow control lever to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (e) Air flow selectionº.
4. Move fan speed control lever to the
HIº position.
(e) Air flow selection
FACE positionÐThis position directs the
air flow to face level.BI-LEVEL positionÐThis position directs
the air flow to face level and floor. Except
in ventilation, the air to the floor is slightly
warmer than that to face level.
FLOOR positionÐThis position directs
the air flow mostly to the floor.
FLOOR / WINDSHIELD position Ð This
position directs the air flow to the wind-
shield and front side windows as well as
the floor.
WINDSHIELD positionÐThis position di-
rects the air flow mostly to the windshield,
front side windows.
(f) Operating tips

Be sure the air inlet grilles in front of the
windshield are not blocked by leaves
or other obstructions.

If air flow control is not satisfactory, check
the side vents. (See Side ventsº.)

When driving on dusty roads, close all
windows. If dust thrown up by the ve-
hicle is still drawn into the vehicle after
closing the windows, it is recom-
mended that the air intake control le-
ver be set to the OUTSIDE AIR posi-
tion and the fan speed control lever
anywhere except the OFFº position.ProCarManuals.com

Part 1Clock
Cigarette lighter and ashtray
101
OPERATION OF
INSTRUMENTS
AND CONTROLSÐ
Chapter 1-8
Other equipment

Clock

Cigarette lighter and ashtray

Glovebox

Cup holder

Luggage cover

Floor mat
The digital clock indicates the time
with the ignition key at the ACCº or
ONº position. To reset the hour, de-
press the Hº button. To reset the min-
utes, depress the Mº button. To ad-
just the time to full hour, depress the
:00º button.
For example, if the :00º button is de-
pressed when the time is between
1:01Ð1:29, the time will change to 1:00.
If the time is between 1:30Ð1:59, the time
will change to 2:00.
When the instrument panel lights are
turned on, the brightness of the time indi-
cation will be reduced.
Once the electrical power source has
been disconnected from the clock, the
time is automatically set to 1:00 (one
o'clock).To operate the cigarette lighter, press
it in. When it becomes heated, it auto-
matically pops out ready for use.
If the engine is not running, the key must
be in the ºACCº position.
Do not hold the cigarette lighter pressed
in.
When finished with your cigarette, thor-
oughly extinguish it in the ashtray to pre-
vent other cigarette butts from catching
fire. After using the ashtray, press it back
in completely.
To remove the ashtray, press down on the
lock spring plate and pull it out.
Use a Toyota genuine cigarette lighter or
equivalent for replacement.
ProCarManuals.com

103
To use the luggage cover, pull it out of
the retractor and hook it to the anchors.To remove the luggage cover, lift up
the luggage cover.Vehicles with rear speakersÐ
For more luggage space, remove the lug-
gage cover board.
Unlock the rear seatback and fold it down
slightly. Pull up the front of the luggage
cover board first, then pull the luggage
cover board toward you.
Luggage cover (wagon)
ProCarManuals.com

106If your engine knocks...
If you detect heavy knocking even when
using the recommended fuel, or if you
hear steady knocking while holding a
steady speed on level roads, consult your
Toyota dealer.
However, now and then, you may notice
light knocking for a short time while accel-
erating or driving up hills. This is no cause
for concern.
GASOLINES CONTAINING DETER-
GENT ADDITIVES
Toyota recommends use of gasolines
that contain detergent additives to
avoid build-up of engine deposits.
For further details, ask your Toyota dealer
or a local gasoline retailer.
GASOLINES CONTAINING MTBE
Gasolines that contain MTBE (Methyl
Tertiary-Butyl Ether) are available in
the market. If you use a gasoline mixed
with MTBE, make certain that it does
not contain more than 15% of MTBE.
If the use of gasolines containing MTBE
causes poor driveability and/or poor fuel
economy, you should discontinue the use
of fuels containing MTBE.GASOLINES CONTAINING ALCOHOL
If you use gasohol in your Toyota, be
sure that it is unleaded, has an octane
rating no lower than 87 and does not
contain more than 10% ethanol.
Gasohol is a mixture of gasoline and etha-
nol.
Toyota does not recommend the use of
gasolines containing methanol. If you use
gasoline containing methanol, use only
gasoline meeting the requirements above
and also containing less than 5% metha-
nol with cosolvents and corrosion inhibi-
tors for methanol.

Do not use gasohol other than
stated above. It will cause fuel
system damage or vehicle perfor-
mance problems.
If driveability problems are en-
countered (poor hot starting, va-
porizing, engine knock, etc), dis-
continue the use.
Take care not to spill gasohol dur-
ing refueling. Gasohol may cause
paint damage.
NOTICE
FUEL TANK CAPACITY
50 L (13.2 gal., 11.0 imp. gal.)If you plan to drive your Toyota in anoth-
er country...
First, comply with the vehicle registration
laws.
Second, confirm the availability of the
correct fuel (unleaded and minimum oc-
tane number).
Operation in foreign countries
ProCarManuals.com

109 The amount of engine oil consumed
depends on the viscosity of the oil, the
quality of the oil and the conditions
the vehicle is driven under.
More oil is consumed by high-speed driv-
ing and frequent acceleration and decel-
eration.
A new engine consumes more oil, since
its pistons, piston rings and cylinder walls
have not become conditioned.
When judging the amount of oil con-
sumption, note that the oil may be-
come diluted and make it difficult to
judge the true level accurately.
As an example, if a vehicle is used for re-
peated short trips, and consumes a nor-
mal amount of oil, the dipstick may not
show any drop in the oil level at all, even
after 1000 km (600 miles) or more. This
is because the oil is gradually becoming
diluted with fuel or moisture, making it ap-
pear that the oil level has not changed.
The diluting ingredients evaporate out
when the vehicle is then driven at high
speeds, as on an expressway, making it
appear that oil is excessively consumed
after driving at high speeds.IMPORTANCE OF ENGINE OIL LEVEL
CHECK
One of the most important points in proper
vehicle maintenance is to keep the engine
oil at the optimum level so that oil function
will not be impaired. Therefore, it is essen-
tial that the oil level be checked regularly.
Toyota recommends that the oil level be
checked every time you refuel the vehicle.
NOTICE
Failure to check the oil level
regularly could lead to serious
engine trouble due to insufficient
oil.
For detailed information on oil level check,
see Checking the engine oil levelº in
Chapter 7-2.TANDEM MASTER CYLINDER BRAKE
SYSTEM
The tandem master cylinder brake system
is a hydraulic system with two separate
sub-systems. If either sub-system should
fail, the other will still work. However, the
pedal will be harder to press, and your stop-
ping distance will be longer. Also, the brake
system warning light may come on.
CAUTION!
Do not drive your vehicle with only
a single brake system. Have your
brakes fixed immediately.
BRAKE BOOSTER
The brake booster uses engine vacuum to
power-assist the brakes. If the engine
should quit while you are driving, you can
bring the vehicle to a stop with normal
pedal pressure. There is enough reserve
vacuum for one or two stopsÐbut no
more!
CAUTION!

Do not pump the brake pedal if the
engine stalls. Each push on the
pedal uses up your vacuum re-
serve.
Brake system
ProCarManuals.com

11 0

Even if the power assist is com-
pletely lost, the brakes will still
work. But you will have to push the
pedal hardÐmuch harder than nor-
mal. And your braking distance will
be longer.
ANTI-LOCK BRAKE SYSTEM (vehicles
with ABSº warning light)
The anti-lock brake system is designed to
prevent lock-up of the wheels during sud-
den braking or braking on slippery road
surfaces. This assists the driver in con-
trolling the vehicle under these circum-
stances.
The anti-lock brake system becomes op-
erative after the vehicle has accelerated
to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the
vehicle decelerates to a speed below
approximately 5 km/h (3 mph).
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
is started. This means that the anti-lock
brake system is in the self check mode,
and does not indicate a malfunction.When the anti-lock brake system function
is in action, you may feel the brake pedal
pulsating and hear a noise. In this situa-
tion, to let the anti-lock brake system
work for you, just hold the brake pedal
down more firmly. Do not pump the brake.
The brake pedal pulsation caused by the
anti-lock brake system may indicate haz-
ardous road surface conditions. Although
the anti-lock brake system assists in pro-
viding vehicle control, it is still important to
drive with all due care, because the anti-
lock brake system cannot overcome the
laws of physics that act on your vehicle:

Braking capability is dependent on tire
friction with the road surface.

Even though the anti-lock brake sys-
tem is operating, a driver cannot main-
tain full control on certain slippery road
surfaces, when cornering at high
speeds, or in violent maneuvers.

Avoid high speeds on wet roads. The
anti-lock brake system cannot elimi-
nate the risk of hydroplaning and loss
of tire friction.Always maintain a safe distance from the
vehicle in front of you. Compared with ve-
hicles not fitted with an anti-lock brake
system, your vehicle may require a longer
stopping distance in the following cases:

Driving on rough, gravel or snow-cov-
ered roads.

Driving with tire chains installed.

Driving on roads where the road sur-
face is pitted or has other differences
in surface height.
ProCarManuals.com

111
ABSº warning light
This light comes on when the ignition key
is turned to the ONº position. After about
3 seconds, the light will go off.
If either of the following conditions occurs,
this indicates a malfunction somewhere in
the parts monitored by the warning light
system. Contact your Toyota dealer as
soon as possible to service the vehicle.

The light does not come on as de-
scribed above, or remains on.

The light comes on while driving.Even if the anti-lock brake system should
fail, the brake system will still operate con-
ventionally. Have your vehicle checked by
your Toyota dealer as soon as possible.The brake pad wear limit indicators on
your disc brakes give a warning noise
when the brake pads are worn to
where replacement is required.
If you hear a squealing or scraping noise
while driving, have the brake pads
checked and replaced by your Toyota
dealer as soon as possible. Expensive ro-
tor damage can result if the pads are not
replaced when necessary.
Brake pad wear limit indicators
ProCarManuals.com

Part 3
How to start the engineÐ
(a) Before cranking Before starting the engine
11 5
STARTING AND
DRIVING

Before starting the engine

How to start the engine

Tips for driving in various
conditions

Winter driving tips

Trailer towing

How to save fuel and make your
vehicle last longer, too
1. Check the area around the vehicle be-
fore entering it.
2. Adjust seat position, seatback angle,
head restraint height and steering wheel
angle.
3. Adjust inside and outside rear view
mirrors.
4. Lock all doors.
5. Fasten seat belts.1. Apply the parking brake firmly.
2. Turn off unnecessary lights and acces-
sories.
3.Manual transmission: Press the
clutch pedal to the floor and shift the
transmission into neutral. Hold the clutch
pedal to the floor until the engine is
started. A starter safety device will pre-
vent the starter from operating if the
clutch pedal is not fully depressed.
Automatic transmission: Put the selec-
tor lever in Pº. If you need to restart the
engine while the vehicle is moving, put the
selector lever in Nº. A starter safety de-
vice will prevent the starter from operating
if the selector lever is in any drive position.
4.Automatic transmission only: De-
press the brake pedal and hold it to the
floor until driving off.
ProCarManuals.com