ECO mode TOYOTA ECHO 2000 Accessories, Audio & Navigation (in English)

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS
2 of 10
Page 2 TOYOTA TVIP SY STEM PROGRAMMING −RS3200

A DD AD DI TIONAL R EMOTE CO NTROL( S) TO SYSTEM
Follow this procedure to add additional rem ote contro ls to a system . The RS3200 may be progra mmed to
operate with a maxi mum of four re mote contro ls. When a new remote controls is progra mmed, it will work
in the default operatio n mode (press the UNLOCK but ton twice to un lock all doors and no AUX button
func tion on 4 but ton remote contro ls); to change the operation mode , you must perfor m the separate
REMOTE CONTROL FUNCTI ON SELECT procedure as sh own on pag es 6 and 7.
























* I f the system does not ac tiv a te the lights, buzzer and door locks 1 t ime, start ov er.
1. Before you begin: Open the dr iv er’s door
and remove the key f rom
the ignition switch .
2. Start the programming procedure. (Co mplete these step s within 40 seconds. )
a. Insert the key into,
and remove it from
the ign ition switch
2 times. b.
Close, then open
the driver’s door
2 times. c.
Insert the key into,
and remove it from
the ignition switch
1 time. d.
Close, the open
the driver’s door
2 times.
e. Insert the key into,
the ignition switch
and leave it in. f.
Close the driver’s
door. g.
Turn t he key from
LOCK to ON, then
back to LOCK. h.
Remove the key
from the ignition
switch.
i. The ta il and marker l ights flas h 1 time,
the buzzer chirps 1 time and the doors
lock and unlock 1 time.*

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS
4 of 10
Page 4 TOYOTA TVIP SY STEM PROGRAMMING −RS3200

REPROGRA M EXISTING REM OTE CON TROLS
Follow this procedure to clear all existing remote control codes and rep\
rogram existing remote controls to
a system. When existing remote controls are reprogrammed, they will work\
in the default operation mode
(press the UNLOCK button twice to unlock all doors and no AUX button fu\
nction on 4 button remote
controls); to change the operation mode, you must perform the separate \
REMOTE CONTROL FUNCTION
SELECT procedure as shown on pages 6 and 7.























*I f the system does not act iv ate the lights, buzzer and d oor locks 2 tim es, start over.
1. Before you begin:
Open the driver’s door and remove the key from
the ignition switch.
2.
Start the programming procedure: (Co mplete these step s within 40 seconds. )
a. Insert the key into,
and remove it from
the ignition switch
2 times. b.
Close, then open
the driver’s door
2 times. c.
Insert the key into,
and remove it from
the ignition switch
1 time. d.
Close, then open
the driver’s door
2 times.
e. Insert the key into
the ignition switch
and leave it in. f.
Close the driver’s
door. g.
Turn t he key from
LOCK to ON 2 times
(ending at LOCK). h.
Remove the key
from the ignition
switch.
i. The ta il and marker l ights flas h 2 times, the buzzer
chirps 2 times and the doors lock and unlock 2 times.*

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS
6 of 10
Page 6 TOY OTA TVIP SY STEM PROGRAMMING −RS3200

REMOTE CON TROL FUNC TION SELEC T
Fol low this procedure to ch ange the opera ting func tions of re mote contro ls already progr am med into a
system. You may change the remote control’s default unlock operation \
mode so that pressing the UNLOCK
button once causes al l doors to unlock at the same time. Also, you may activ ate the AUX button func tion
on 4 button remote cont rols.
























* I f the system does not ac tiv a te the lights, buzzer and door locks 4 t imes, start over .
1. Before you begin:
Open the driver’s door and remo ve the key
f rom the ign ition switch .

2.
Start the programming procedure. (Co mplete these step s within 40 seconds. )
a. Insert the key into,
and remove it from
the ignition switch
2 times. b.
Close, then open
the driver’s door
2 times. c.
Insert the key into,
and remove it from
the ignition switch
1 time. d.
Close, then open
the driver’s door
2 times.
e. Insert the key into,
the ignition switch
and leave it in. f.
Close the driver’s
door. g.
Turn t he key from
LOCK to ON 4 times
(ending at LOCK). h.
Remove the key
f rom the ign ition
switch.
i. The tail and marker lights flash 4 times,
the buzzer chirps 4 times and the doors
lock and unlock 4 times.*

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS
9 of 10
9

e
g
a
P

G
N
I
M
M
A
R
G
O
R
P

M
E
T
S
Y
S

P
I
V
T

A
T
O
Y
O
T

P ASS IVE ARMING ON/ OFF SELE CTIO N AND ENTRY DEL AY TIME SELEC TION

The RS3200 is fa ctory set to not passi vely ar m. To cha nge the system’s operation for passive arming,
as well as to adjust the entry delay time, f ollow the procedure below .
































1. Before you begin:
Close all the doors and the trunk or hatch, unlock all th e doors with the inside
lock switch, then remove the key fro m th e igni tion switc h.

a.
Using a remote control,
lock, then unlock the
doors 3 times.
2.
Start the programming procedure. (Co mplete these steps within 30 seconds. ) b. Open the dr iv er’s door.c. Lock, then unlock the
dri ver’s door ins ide lock
butt on 3 time s.
d. The system locks the door
in 2 seconds; i f th is does
not happen, start o ver. e. Unlock the driver’s door
inside lock button.
a. Close, then open the door :
2 t im es= passi ve arming off
3 times= passi ve arming on,
0 sec. entr y delay.
4 ti mes= passi ve arming on,
15 sec. entry delay.
5 ti mes= passi ve arming on,
30 sec. entry delay.
b.
Lock, then unlock the
driver’s door inside
lock button 1 time. c. The system locks the
door in 2 seconds;
Programming is now
complete . If this does not
happen, start o ver.
3. Select the operating mode and entry time delay, and co mplete the
programming ste ps.

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS
10 of 10
Page 10 TOYOTA TVIP S YSTEM PROGRAMMING −RS3200

IGNITI ON−CON TROLLED AU TOMA TIC DOOR LOCK/ UNLO CK
W hen al l doors are c losed, the RS3200 is fac tory set to auto matically loc k the v ehic le’s door when the
igni tion key is turned to ON or START , and unlock them (open or not) when the key is turned bac k to
ACC or LOCK . Follow the procedure below to change t his feature’s operation mode .























1. Before you begin:
Open the dr iv er’s door and remo ve the key
f rom the ign ition switch .

2.
Start the programming procedure. (Co mplete these step s within 30 seconds.)
a. Insert the key into the
igni tion switch and turn it
from LOCK to ON 5 times
(ending a t ON).
b.
The ta il and marker lig hts
flash 1 time, and the b uzzer
c hirps 1 time. c. The status mon itor’s LED
(or the engine immobi lizer
system’s LED) turns on
for 30 seconds.
Note: I f the s
ystem does not act iv ate the lights and buzzer, start over .
3. Select the operating mode and co mplete the programming steps.

a. Close the door: Ig nition
controlled door locks on .

Close, then o pen and close
the door: Ignition controlled
door locks off. b.
Turn the ignition key
back to lock. c. The ta il and marker l ights flas h 1
time, and t he buzzer chirps 1 time
i f the system was set for I G door
lock co ntrol ON, twice f or IG door
lock control OFF. I f this does not
happen, start o ver: otherwise,
program ming is now complete .