torque TOYOTA ECHO 2005 1.G Owners Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2005, Model line: ECHO, Model: TOYOTA ECHO 2005 1.GPages: 268, PDF Size: 5.09 MB
Page 200 of 268
1922005 ECHO from Aug. ’04 Prod. (OM52636U)
—Lowering your vehicle
SU41127
9. Lower the vehicle completelyand tighten the wheel nuts.
Turn the jack handle counterclock-
wise to lower the vehicle.
Use only the wheel nut wrench to
tighten the nuts. Do not use other
tools or any additional leverage other
than your hands, such as a hammer,
pipe or your foot. Make sure the
wrench is securely engaged over the
nut.
Tighten each nut a little at a time in
the order shown. Repeat the process
until all the nuts are tight.
CAUTION
When lowering the vehicle,
make sure all portions of your
body and all other persons
around will not be injured as
the vehicle is lowered to the
ground.
Have the wheel nuts tightened
with torque wrench to 103 N·m
(10.5 kgf·m, 76 ft·lbf), as soon
as possible after changing
wheels. Otherwise, the nuts
may loosen and the wheels
may fall off, which could cause
a serious accident.
SY41019
10.Reinstall the wheel ornament.
1. Put the wheel ornament into posi- tion.
On some models, align the cutout
of the wheel ornament with the
valve stem as shown.
2. Press hand firmly on one side of wheel ornament and then firmly
tap the other side around the edge
of wheel ornament with the heel
of your hand to snap into place.
—Reinstalling wheel ornament
(steel wheel)
Page 201 of 268
1932005 ECHO from Aug. ’04 Prod. (OM52636U)
CAUTION
Take due care in handling the or-
nament to avoid unexpected per-
sonal injury.
—After changing wheels
11. Check the air pressure of the re-placed tire.
Adjust the air pressu re to the specifi-
cation designed in Section 8. If the
pressure is lower, dr ive slowly to the
nearest service station and fill to the
correct pressure.
Do not forget to reinstall the tire valve
cap as dirt and moisture could get into
the valve core and possibly cause air
leakage. If the cap is missing, have
a new one put on as soon as possible.
12.Restow all the tools, jack and
flat tire securely.
As soon after changing wheels as
possible, tighten the wheel nuts to the
torque specified in Section 8 with a
torque wrench and have a technician
repair the flat tire.CAUTION
Before driving, make sure all the
tools, jack and flat tire are se-
curely in place in their storage
location to reduce the possibility
of personal injury during a colli-
sion or sudden braking.
Page 259 of 268
2512005 ECHO from Aug. ’04 Prod. (OM52636U)
Tires
Tire size and cold tire inflation pressure:
Except spare tirekPa (kgf/cm
2 or bar, psi)
Ti r e siz e
FrontRearWheel size
P175/65R14 81S220 (2.2, 32)220 (2.2, 32)14 x 5 1/ 2J , 14 x 5 1/ 2J J
P185/60R15 84T220 (2.2, 32)220 (2.2, 32)15 x 5J
Spare tire Ti r e siz e
Tire inflation pressure kPa (kgf/cm2 or bar, psi)Wheel size
T115/70D14∗1420 (4.2, 60)14 x 4T
T125/70D16∗2420 (4.2, 60)16 x 4T
∗1: With P175/65R14 81S tires∗2: With P185/60R15 84T tires
Wheel nut torque, N·m (kgf·m, ft·Ibf): 103 (10.5, 76)
NOTE: For a complete information on tires (e.g. replacing ti res or replacing wheels), see “Checking tire inflation pres-
sure” through “Aluminum wheel precautions”, page 227 through 235 in Section 7 −2.