instrument panel TOYOTA FJ CRUISER 2007 1.G User Guide

1352007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
The cruise control is designed to main-
tain a set cruising speed without requir-
ing the driver to operate the accelera-
tor. Cruising speed can be set to any
speed above 40 km/h (25 mph).
Within the limits of the engine’s capabili-
ties, cruising speed can be maintained up
or down grades. However, changes in ve-
hicle speed may occur on steeper grades.
CAUTION
To help maintain maximum control
of your vehicle, do not use the
cruise control when driving in
heavy or varying traffic, or on slip-
pery (rainy, icy or snowcovered) or
winding roads.
Avoid vehicle speed increases when
driving downhill. If the vehicle
speed is too fast in relation to the
cruise control set speed, cancel the
cruise control then downshift the
transmission to use engine braking
to slow down.
TS17013
TURNING THE SYSTEM ON AND OFF
To turn the cruise control on, press the
“ON−OFF” button. The “CRUISE” indicator
light on the instrument panel will come on
to indicate that the cruise control is opera-
tional. Pressing the “ON −OFF” button
again turns the system off.
When the system is turned off, cruising
speed must be reset when the cruise con-
trol is turned on again.
CAUTION
Due to the cruise control switch be-
ing located just behind the steering
wheel, there is a possibility that it
may be touched accidentally. To avoid
accidentally engaging the cruise con-
trol, turn the system off when it is
not in use. Make sure the “CRUISE”
indicator light is off.
Cruise control

1402007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
PS18502
Type 1: AM·FM radio/compact disc player
/MP3/WMA player (with compact disc
changer controller)
TS18001a
Type 2: AM·FM radio/compact disc player
with changer/MP3/WMA player (with XM
satellite radio
∗ controller)
∗: Use of satellite radio requires XM
tuner and service. Contact your Toyota
dealer for details. This section describes some of the basic
features on Toyota audio systems. Some
information may not pertain to your sys-
tem.
Your audio system works when the ignition
key is in the “ACC” or “ON” position.
Welcome function (type 2)
When you turn the ignition switch to the
“ACC” or “ON” position, “FJ CRUISER”
will appear scrolling on the display. And
then “FJammer” will appear for 6 seconds.
While this function is operating, the dis-
play is illuminated with full intensity and
the instrument panel light control dial is
disabled. However, you can turn off the
display illumination by pushing the
“PWR·VOL” knob.
TURNING THE SYSTEM ON AND OFF
Push “PWR·VOL” to turn the audio system
on and off.
Push “AM”, “FM1”, “FM2”,
“AM·SAT”∗ or
“DISC·AUX” to turn on that function with-
out pushing “PWR·VOL”. To turn on the
compact disc player, a compact disc must
be loaded in the player.
You can turn on the compact disc player
by inserting a compact disc.
Reference Using your audio system—
—Some basics

1732007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Fan speed selector
Turn the knob to adjust the fan speed—to
the right to increase, to the left to de-
crease.
Temperature selector
Turn the knob to adjust the temperature—
to the right to warm, to the left to cool.
G18021
Air flow selector
Turn the knob to select the vents used for
air flow.1. Panel— Air flows mainly from the
instrument panel vents.
2. Bilevel— Air flows from both the floor
vents and the instrument panel vents.
3. Floor— Air flows mainly from the floor
vents.
4. Floor/Windshield— Air flows mainly
from the floor vents and windshield
vents.
Turning the air flow selector to the
floor/windshield position turns on the
defogging/defrosting function with the
purpose of clearing the windshield. In this position, air intake selector
mode changes to FRESH automatically
to clear the windshield quickly. If you
want to return the setting to RECIRCU-
LATE mode, press the air intake selec-
tor button once again.
5. Windshield— Air flows mainly from the
windshield vents.
Turning the air flow selector to the
windshield position turns on the defog-
ging/defrosting function with the pur-
pose of clearing the windshield.
In this position, air intake selector
mode changes to FRESH automatically
to clear the windshield quickly. It is not
possible to return to RECIRCULATE in
this position.
For details about air flow selector settings,
see “Air flow selector settings” described
below.

1932007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
The protection circuit may be activated to
cut the power supply if any of the follow-
ing conditions apply:
The engine is started with the power
outlet switch on.
Use of electrical appliances exceeding
the maximum capacity is attempted.
A sound may be heard when the
protection circuit is activated. This is
normal and does not indicate a mal-
function.
Electrical appliances, which consume
power exceeding 100W, have been
used continuously for a long time per-
iod.
The total power usage by all electrical
features (headlights, air conditioning,
etc.) has exceeded the total vehicle
maximum for an extended period of
time.
If the protection circuit is activated and
the power supply is cut, conduct the fol-
lowing procedure:
1. Park the vehicle in a safe area, and then securely apply the parking brake.
2. Check and ensure the following condi- tions: Automatic transmission models: The
selector lever is in the “P” or “N” posi-
tion.
Manual transmission models: The shift
lever is in the neutral position and the
clutch pedal is not depressed.
3. Make sure that the power consumption of the electric appliance is within the
maximum capacity of the power outlet
and the appliance is not broken.
4. Push the power outlet main switch again.
When the cabin temperature is high, open
the windows to cool the temperature
down. Once it reaches the normal temper-
ature, turn the power outlet main switch
on again.
If the power supply is not resumed even
after performing the above procedure,
have the vehicle inspected by a Toyota
dealer.
TS10003
Indicator light
(green)
Indicator light
(yellow)
To use the power outlet, push the main
switch located on the instrument panel.
The color of the indicator light changes
according the maximum available capacity,
as follows: Illumination color
Maximum capacity
Green and yellow115 VAC/400W
Ye l l o w115 VAC/100W
To turn the power outlet off, push the
main switch again. When the power outlet
is not in use, make sure that the main
switch is off and that the indicator light is
not illuminated.

1972007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS10012
Type A (instrument panel)
TS10013
Type B (right side of luggage compart-
ment)
The cup holder is designed for holding
cups or drinkcans securely. To use
them, observe the following illustra-
tions.
CAUTION
Do not place anything else other than
cups or drinkcans in the cup holder,
as such items may be thrown about
and possibly injure people in the ve-
hicle during sudden braking or in an
accident.
TS10018a
Type A (vehicles with automatic transmis-
sion)
Cup holders

2152007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS20012
The rear bumper is for rear end protec-
tion and easier stepup loading.
To get on the rear step bumper, use the
shaded area between the arrows in the
illustration.
CAUTION
Do not allow more than one person
to get on the rear step bumper at
a time. It is designed for only one
person.
Never drive the vehicle with anyone
on the rear step bumper.
TS20006
The vehicle identification number (VIN)
is the legal identifier for your vehicle.
This number is on the left top of the
instrument panel, and can be seen
through the windshield from outside.
This is the primary identification number
for your Toyota. It is used in registering
the ownership of your vehicle.
TS20007
The vehicle identification number (VIN) is
also on the Certification Label.
Rear step bumperYour Toyota’s identification—
—Vehicle identification number

2262007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Cargo capacity
Cargo capacity may increase or de-
crease depending on the size (weight)
and the number of occupants. For de-
tails, see “Capacity and distribution”
that follows.
CAUTION
Do not apply the load more than
each load limit. That may cause
not only damage to the tires, but
also deterioration to the steering
ability and braking ability, which
may cause an accident.
When stowing cargo and luggage in
the vehicle, observe the following: Put cargo and luggage in the lug-
gage compartment when at all
possible. Be sure all items are se-
cured in place.
 Be careful to keep the vehicle bal-
anced. Locating the weight as far
forward as possible helps maintain
balance.
 For better fuel economy, do not
carry unneeded weight.
CAUTION
To prevent cargo and l uggage
from sliding forward during
braking, do not stack anything
in the luggage compartment
higher than the seatbacks.
Keep cargo and luggage low,
as close to the floor as pos-
sible.
 Do not place anything on the
flattened seat or it may slide
forward during braking.
 Never allow anyone to ride in
the luggage compartment. It is
not designed for passengers.
They should ride in their seats
with their seat belts properly
fastened. Otherwise, they are
much more likely to suffer
death or serious bodily injury,
in the event of sudden braking
or a collision.
 Do not drive with objects left
on top of the instrument panel.
They may interfere with the
driver’s field of view. Or they
may move during sharp vehicle
acceleration or turning, and im-
pair the driver’s control of the
vehicle. In an accident they
may injure the vehicle occu-
pants.
Cargo and luggage—
—Stowage precautions

2762007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Carpets
Use a good foamtype shampoo to
clean the carpets.
Begin by vacuuming thoroughly to remove
as much dirt as possible. Several types of
foam cleaners are available; some are in
aerosol cans and others are powders or
liquids which you mix with water to pro-
duce a foam. To shampoo the carpets,
use a sponge or brush to apply the foam.
Rub in overlapping circles.
Do not apply water—the best results are
obtained by keeping the carpet as dry as
possible. Read the shampoo instructions
and follow them closely.
Seat belts
The seat belts may be cleaned with
mild soap and water or with lukewarm
water.
Use a cloth or sponge. As you are clean-
ing, check the belts for excessive wear,
fraying, or cuts.NOTICE
Do not use dye or bleach on the
belts—it may weaken them.
 Do not use the belts until they be-
come dry.
Windows
The windows may be cleaned with any
household window cleaner.
NOTICE
When cleaning the inside of the rear
window, be careful not to scratch or
damage the heater wires or connec-
tors.
Air conditioning control panel, audio
panel, instrument panel, console panel
and switches
Use a soft damp cloth for cleaning.
Soak a clean soft cloth in water or luke-
warm water then lightly wipe off dirt.
NOTICE
Do not use organic substances (sol-
vents, kerosene, alcohol, gasoline,
etc.) or alkaline or acidic solutions.
These chemicals can cause discol-
oring, staining or peeling of the
surface.
 If you use cleaners or polishing
agents, make sure their ingredients
do not include the substances men-
tioned above.
 If you use a liquid car freshener, do
not apill the liquid onto the ve-
hicle’s interior surfaces. It may con-
tain the ingredients mentioned
above. Immediately clean any spill
using the method mentioned above.
Leather interior
The leather upholstery may be cleaned
with neutral detergent for wool.
Remove dirt using a soft cloth dampened
with 5% solution of neutral detergent for
wool. Then thoroughly wipe off all traces
of detergent with a clean damp cloth.

3212007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS80001a
Engine compartment
Fuses (type A)1. SPARE 10 A: Spare fuse
2. SPARE 15 A: Spare fuse
3. TOWING TAIL 15 A: Trailer lights
4. OFFROAD LP 15 A: Offroad lamp
5. STOP 10 A: Stop lights, high mounted
stoplight, anti −lock brake system, trac-
tion control system, active traction con-
trol system, vehicle stability control
system, “AUTO LSD” system, multiport
fuel injection system/sequential multi-
port fuel injection system, shift lock
system
6. AUX LP 15 A: Driving lamp
TS80002
Instrument panel
7. OBD 7.5 A: On−board diagnosis sys-
tem
8. HEAD (LO RH) 10 A: Right −hand
headlight (low beam) (vehicles with
daytime running light), right −hand head-
light (vehicles without daytime running
light)
9. HEAD (LO LH) 10 A: Left−hand head-
light (low beam) (vehicles with daytime
running light), left −hand headlight (ve-
hicles without daytime running light)
10. HEAD (HI RH) 10 A: Right −hand head-
light (high beam)
TS80003a
Engine compartment
11. HEAD (HI LH) 10 A: Left −hand head-
light (high beam)
12. EFI NO.2 10 A: Multiport fuel injection
system/s equential multiport fuel injec-
tion system
13. DRL 7.5 A: Daytime running light
system
14. DEFOG 30 A: Back window defogger
15. DEFOG NO.2 7.5 A: Multiport fuel in-
jection system/sequential multiport fuel
injection system
16. DOME 10 A: Interior light, luggage
compartment light, clock, accessory
meter, meter and gauge
Fuses

3222007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
17. RADIO NO.1 20 A: Audio system
18. ECUB 10 A: Air conditioning system,
multiplex communication system, SRS
airbag system, front passenger occu-
pant classification system
19. ALTS 7.5 A: Charging system
20. HORN 10 A: Horn
21. A/F HEATER 15 A: Multiport fuel injec-
tion system/sequential multiport fuel in-
jection system
22. TRNHAZ 15 A: Turn signal lights,
emergency flashers
23. ETCS 10 A: Multiport fuel injection
system/s equential multiport fuel injec-
tion system, electronic throttle control
system
24. EFI 20 A: “EFI NO.2” fuse, Multiport
fuel injection system/sequential multi-
port fuel injection system
25. DR/LCK 20 A: Door lock system, mul-
tiplex communication system
26. TOWING 15 A: Towing converter
27. RADIO NO.2 20 A: Audio system28. IGN 10 A:
Multiport fuel injection sys-
tem/sequential multiport fuel injection
system, anti −lock brake system, vehicle
stability control system, traction control
system, active traction control system,
“AUTO LSD” system, SRS airbag sys-
tem, front passenger occupant classifi-
cation system
29. GAUGE 7.5 A: Meter and gauge
30. FR WIPWSH 30 A: Windshield wipers
and washer
31. 4WD/DIFF 20 A: Four−wheel drive sys-
tem, rear differential lock system
32. PWR OUTLET 15 A: Power outlet
33. RR WSH 15 A: Back window wiper
and washer, multiplex communication
system
34. ECUIG 10 A: Anti−lock brake system,
vehicle stability control system, traction
control system, active traction control
system, “AUTO LSD” system, multiport
fuel injection system/sequential multi-
port fuel injection system, cruise con-
trol system, back door lock system,
shift lock system, multiplex communica-
tion system 35. IG1 15 A:
Turn signal lights, air condi-
tioning system, charging system, clutch
start cancel switch, anti −lock brake
system, traction control system, active
traction control system, vehicle stability
control system, “AUTO LSD” system,
back −up lights, intuitive parking assist,
rear differential lock system, power out-
let, accessory meter, meter and gauge
36. STA 7.5 A: Starting system, clutch
start cancel switch, power outlet
37. TAIL 10 A: Tail lights, license plate
lights, parking lights, instrument panel
light control, illuminations
38. ACC 7.5 A: Shift lock system, outside
rear view mirrors, audio system, power
outlet, clock, accessory meter, multi-
plex communication system
Fuses (type B)
39. AM1 50 A: “ACC”, “ECU−IG”, “IG1”,
“PR WSH”, “FR WIP −WSH”, “4WD/
DIFF” and “STA” fuses
40. J/B 50 A: “TAIL”, “PWR OUTLET”,
“POWER”
4

1. ABS MTR 40 A: Anti−lock brake sys-
tem, vehicle stability control system,
traction control system, active traction
control system, “AUTO LSD” system