tow TOYOTA FJ CRUISER 2007 1.G User Guide

11 82007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
With the selector lever in “3” or “2”, the
vehicle will start in first gear and automat-
ically shift to third gear or second gear.
With the selector lever in “L”, the trans-
mission is engaged in first gear.
NOTICE
Be careful not to overrev the en-
gine. Watch the tachometer to keep
engine rpm from going into the red
zone. The approximate maximum al-
lowable speed for each position is
given below for your reference:
Twowheel drive models
“3” 148 km/h (92 mph) . . . . . . .
“2” 101 km/h (63 mph) . . . . . . .
“L” 58 km/h (36 mph) . . . . . . . .
Fourwheel drive models
Fourwheel drive control lever
at “H2” or “H4”“3” 148 km/h (92 mph) . . . . . . .
“2” 101 km/h (63 mph) . . . . . . .
“L” 58 km/h (36 mph) . . . . . . . .
Fourwheel drive control lever
at “L4” “3” 56 km/h (35 mph) . . . . . . . .
“2” 38 km/h (24 mph) . . . . . . . .
“L” 22 km/h (14 mph) . . . . . . . .
Do not continue hill climbing or
hard towing for a long time in the
“3”, “2” or “L” position. This may
cause severe automatic transmis-
sion damage from overheating. To
prevent such damage, “4” position
should be used in hill climbing or
hard towing.
(e) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the selector lever to the
“R” position.
NOTICE
Never shift into reverse while the ve-
hicle is moving.
(f) Parking
1. Bring the vehicle to a complete stop.
2. With the brake pedal pressed down, fully depress the parking brake pedal
to apply the parking brake securely.
3. With the brake pedal pressed down, shift the selector lever to the “P” posi-
tion.
CAUTION
Never attempt to move the selector
lever into “P” position under any cir-
cumstances while the vehicle is mov-
ing. Serious mechanical damage and
loss of vehicle control may result.
(g) Good driving practice
If the transmission repeatedly shifts up
and down between fourth gear and
overdrive when climbing a gentle slope,
shift the selector lever to the “4” posi-
tion. Be sure to shift the selector lever
to the “D” position immediately after-
ward.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use “D” position.
CAUTION
Always keep your foot on the brake
pedal while stopped with the engine
running. This prevents the vehicle
from creeping.

1202007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Maximum allowable speeds
To get on a highway or to pass slower
traffic, maximum acceleration may be nec-
essary. Make sure you observe the follow-
ing maximum allowable speeds in each
gear:gear km/h (mph) “H” or “HL” “LL”
1 48 (30) 18 (11)
2 93 (58) 35 (22)
3 138 (86) 53 (33)
4 172 (107) 66 (41)
5 175 (109) 80 (50)
NOTICE
Do not downshift if you are going
faster than the maximum allowable
speed for the next lower gear.
Good driving practice
If it is difficult to shift into reverse, put
the transmission in neutral, release the
clutch pedal momentarily, and then try
again.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use sixth gear.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to skid or
spin.
NOTICE
 Make sure the vehicle is completely
stopped before shifting into reverse.
 Do not use any gears other than
first gear when starting off and
moving forward. Doing so may dam-
age the clutch.
TS17005
Use the fourwheel drive control lever
to select the following transfer modes.
“H” (high speed position): Lever at “H”
Use this for normal driving on dry hard −
surfaced roads. This position gives greater
economy, quietest ride and least wear.
“HL” (high speed position, center differ-
ential locked): Lever at “HL”
Use this for normal driving on wet, icy or
snow −covered roads.
“N” (neutral position): Lever at “N”
No power is delivered to the wheels. The
vehicle must be stopped.
Fourwheel drive system
(fulltime fourwheel drive
models)—
(a) Fourwheel drive control

1762007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
If following another vehicle on a dusty
road, or driving in windy and dusty
conditions, it is recommended that the
air intake selector be temporarily set to
RECIRCULATE, which will close off the
outside passage and prevent outside
air and dust from entering the vehicle
interior.Heating
For best results, set controls to:
Fan speed— Any setting except “OFF”
Temperature— To w a r d s WARM (red
zone)
Air intake—FRESH (outside air)
Air flow—FLOOR
Air conditioning—OFF
For quick heating, select recirculated
air for a few minutes. To keep the
windows from fogging, select fresh af-
ter the vehicle interior has been
warmed.
Press the “A/C” button on for dehumidi-
fied heating.
Choose floor/windshield air flow to heat
the vehicle interior while defrosting or
defogging the windshield.
Air conditioning
For best results, set controls to:
Fan speed— Any setting except “OFF”
Temperature— To w a r d s COLD (blue
zone)
Air intake—FRESH (outside air)
Air flow—PANEL
Air conditioning—ON
TS19011
For quick cooling, turning the temperature
selector knob fully towards COLD (MAX
A/C) changes the air intake selector mode
to RECIRCULATE.

1842007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS10005
The outside temperature display indi-
cates the outside air temperature. The
displayed value is updated.
To set the unit, push the “E/M” button
until the desired unit display appears.
The displayed temperature ranges from
−30 C ( −22 F) up to 50 C (122 F).
If an abnormality exists in the connection
of the outside air temperature sensor,
“ −− C” (“ −−F”) will appear on the display.
If “ −−C” (“ −−F”) appears on the display,
contact your Toyota dealer.
There may be a case that “−− C” (“ −−F”)
appears momentarily when the ignition is
quickly turned to “ON”. It is normal if it
goes out soon.
TS10006
The compass indicates the direction
that the vehicle is heading. In the
above case, it indicates that the vehicle
is heading north.
Displays
Directions
NE
S
WNorth
East
South West
The compass points north for about 3 sec-
onds after the ignition switch is turned to
the “ON” position, and then indicates the
actual direction the vehicle facing. When
the ignition switch is turned to the “ACC”
or “LOCK” position, it indicates the actual
direction for about 5 seconds and then
points in a random direction.
The compass may not indicates the cor-
rect direction in the following conditions:
The vehicle is stopped immediately af-
ter turning.
The compass does not adjust while the
vehicle is stopped.
The ignition switch is turned off imme-
diately after turning.
The vehicle is on an inclined surface.
The vehicle is in a place where the
earth’s magnetic field is subject to in-
terference by artificial magnetic fields
(underground parking, under a steel
tower, between buildings, roof parking,
near a crossing, near a large vehicle,
etc.).
The vehicle is magnetized. (There is a
magnet or a metal object on or near
the accessory meter.)
The battery has been disconnected.
—Outside temperature display —Compass

1872007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS10009a
CALIBRATING THE COMPASS (circling
calibration)
Sometimes the direction display on the
compass may not change after a turn. To
rectify this, stop the vehicle and do as
follows.1. Push and hold the “SET” button for about 2 seconds. The zone number ap-
pears on the outside temperature dis-
play.
2. Push the “SET” button. “ −−” will start
moving.
TS10010
3. Drive the vehicle in a circle at 8 km/h (5 mph). If there is not enough space
to drive in a circle, drive around the
block.
When the compass display returns to the
outside temperature display, calibration is
complete.
When circling calibration fails, “Er” is dis-
played for 2 seconds and then “COM-
PASS” flashes. It also flashes when cir-
cling calibration is not completed.
If you want to cancel the calibration be-
fore it is complete, push the “SET” button
for about 2 seconds. Perform circling calibration just after
you have purchased your Toyota. And
then always perform circling calibration
after the battery has been removed, re-
placed or disconnected.
Do not perform circling calibration of
the compass in a place where the
earth’s magnetic field is subject to in-
terference by artificial magnetic fields
(underground parking, under a steel
tower, between buildings, roof parking,
near a crossing, near a large vehicle,
etc.).
During calibration, do not operate elec-
tric systems (power windows, etc.) as
they may interfere with the calibration.

1912007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
In the following cases, the system may
not work properly.
When ice, snow, mud or other objects
build up on the sensor.
When the vehicle is parked in extreme-
ly high or extremely low temperature
for a long period.
When driving on bumpy or graveled
roads or on grass.
When a device such as a horn from
another vehicle, motorcycle engine, or
an air brake sound from a heavy −duty
vehicle, issues ultrasonic waves, near
your vehicle.
When attaching a two −way radio anten-
na.
When rain or water splashes on the
sensor.
When operating the vehicle on an in-
clined surface.
When a radio antenna or fender pole
is mounted on your vehicle.
When a towing hitch is mounted on
your vehicle. The system may not detect the follow-
ing.
Thin objects such as a wire or rope
Objects with a surface area too small
to reflect ultrasonic waves such as
wire gauze
Sound wave absorbing objects or mate-
rial such as cotton or snow
A person near the vehicle (depending
on the type of clothes worn)
Objects with a sharp edge
Small or short objects
Tall objects with an upper part project-
ing toward the vehicle
Objects just under the bumper
Objects very close to your vehicle
In the following cases, have your
Toyota dealer check the system.
When the bumper is damaged.
When the buzzer keeps sounding inter-
mittently even though nothing is close
to the sensors.
TS10001a
The power outlet is designed for power
supply for car accessories.
The key must be in the “ACC” or “ON”
position for the power outlet to be used.
Power outlet (12 VDC)

2002007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS10014a
To secure your luggage, use the tie
down hooks as shown above.
See “—Stowage precautions” on page 226
in Section 2 for precautions when loading
luggage.
CAUTION
To avoid personal injury, keep the tie
down hooks folded in place on the
floor when not in use.
NOTICE
Do not use the seat anchors instead
of the tiedown hooks.
TS10015
Grocery bag hooks
TS10024
Cargo net hooks
These hooks are designed to hang
things like grocery bags or cargo net.
To hang the cargo net, use the cargo net
hooks and rear tie−down hooks.
Although the cargo net itself is not in-
cluded as an original equipment, these
hooks can be used to hang the cargo net.
NOTICE
 To prevent damage to the hooks, do
not hang any object heavier than 4
kg (8.8 lb.) in them.
 To prevent damage to the hook,
avoid hanging things other than a
cargo net on it when using them as
cargo net hooks.
Tiedown hooks Grocery bag/cargo net hooks

2052007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Always slow down in gusty cross-
winds. Because of its profile and
higher center of gravity, your ve-
hicle is more sensitive to side
winds than an ordinary passenger
car. Slowing down will allow you to
have better control.
When driving offroad or in rugged
terrain, do not drive at excessive
speeds, jump, make sharp turns,
strike objects, etc. This may cause
loss of control or vehicle rollover
causing death or serious injury. You
are also risking expensive damage
to your vehicle’s suspension and
chassis.
Do not drive horizontally across
steep slopes. Driving straight up or
straight down is preferred. Your ve-
hicle (or any similar offroad ve-
hicle) can tip over sideways much
more easily than forward or back-
ward.
Drive gently and avoid high speeds.
Your vehicle does not need an elaborate
break−in. But following a few simple tips
for the first 1600 km (1000 miles) can add
to the future economy and long life of
your vehicle:
Avoid full throttle acceleration when
starting and driving.
Avoid racing the engine.
Try to avoid hard stops during the first
300 km (200 miles).
Do not drive for a long time at any
single speed, either fast or slow.
Do not tow a trailer during the first 800
km (500 miles). FUEL TYPE
Your new vehicle must use only un-
leaded gasoline.
To help prevent gas station mix
−ups, your
Toyota has a smaller fuel tank opening.
The special nozzle on pumps with un-
leaded fuel will fit it, but the larger stan-
dard nozzle on pumps with leaded gas will
not.
At a minimum, the gasoline you use
should meet the specifications of ASTM
D4814 in the U.S.A. and CGSB 3.5 −M93
in Canada.NOTICE
Do not use leaded gasoline. Use of
leaded gasoline will cause the three
way catalytic converter to lose its ef-
fectiveness and the emission control
system to function improperly. Also,
this can increase maintenance costs.
Breakin period Fuel

2252007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Vehicle load limits include total load
capacity, seating capacity, towing ca-
pacity and cargo capacity. Follow the
load limits shown below. Total load ca-
pacity and seating capacity are also
described on the tire and loading in-
formation label. For location of the tire
and loading information label, see
“Checking tire inflat ion pr es s ur e” on
page 297.
Total load capacity:
540 kg (1190 lb.)
Total load capacity means combined
weight of occupants, cargo and lug-
gage. Tongue load is included when
trailer towing. Seating capacity:
Total 5 (Front 2, Rear 3)
Seating capacity means the maximum
number of occupants whose esti-
mated average weight is 68 kg (150
lb.) per person. Depending on the
weight of each person, the seating ca-
pacity given may exceed the total
load capacity.
NOTICE
Even if the number of occu-
pants are within the seating ca-
pacity, do not exceed the total
load capacity.
Towing capacity: 2268 kg (5000 lb.)
Towing capacity means the maximum
gross trailer weight (trailer weight plus
its cargo weight) that your vehicle is
able to tow.
Veh icle lo ad limit s

2262007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Cargo capacity
Cargo capacity may increase or de-
crease depending on the size (weight)
and the number of occupants. For de-
tails, see “Capacity and distribution”
that follows.
CAUTION
Do not apply the load more than
each load limit. That may cause
not only damage to the tires, but
also deterioration to the steering
ability and braking ability, which
may cause an accident.
When stowing cargo and luggage in
the vehicle, observe the following: Put cargo and luggage in the lug-
gage compartment when at all
possible. Be sure all items are se-
cured in place.
 Be careful to keep the vehicle bal-
anced. Locating the weight as far
forward as possible helps maintain
balance.
 For better fuel economy, do not
carry unneeded weight.
CAUTION
To prevent cargo and l uggage
from sliding forward during
braking, do not stack anything
in the luggage compartment
higher than the seatbacks.
Keep cargo and luggage low,
as close to the floor as pos-
sible.
 Do not place anything on the
flattened seat or it may slide
forward during braking.
 Never allow anyone to ride in
the luggage compartment. It is
not designed for passengers.
They should ride in their seats
with their seat belts properly
fastened. Otherwise, they are
much more likely to suffer
death or serious bodily injury,
in the event of sudden braking
or a collision.
 Do not drive with objects left
on top of the instrument panel.
They may interfere with the
driver’s field of view. Or they
may move during sharp vehicle
acceleration or turning, and im-
pair the driver’s control of the
vehicle. In an accident they
may injure the vehicle occu-
pants.
Cargo and luggage—
—Stowage precautions