set clock TOYOTA HIGHLANDER 2001 Service Repair Manual

'05 HIGHLANDER_U (L/O 0409)
4
2005 HIGHLANDER from Nov. '04 Prod. (OM48570U)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches
3. Emergency flasher switch
4. Clock
5. Front passenger 's seat belt reminder
light
6. Rear window and outside rear view
mirror defogger and windshield wiper
de- icer switch
7. Air conditioning controls
8. Audio system
9. AIRBAG ONº and AIRBAG OFFº
indicator lights
10. Snow mode button
11. Seat heater switches
12. Cigarette lighter
13. TRAC OFFº switch
(two- wheel drive models)
14. Cruise control switch
15. Ignition switch
16. Tilt steering lock release lever
17. Tire pressure warning system reset
switch
Vehicles with manual air conditioning controls (view B)

'05 HIGHLANDER_U (L/O 0409)
6
2005 HIGHLANDER from Nov. '04 Prod. (OM48570U)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches
3. Emergency flasher switch
4. Clock
5. Front passenger 's seat belt reminder
light
6. Air conditioning controls and
multi- information display
7. Rear window and outside rear view
mirror defogger and windshield wiper
de- icer switch
8. Audio system
9. AIRBAG ONº and AIRBAG OFFº
indicator lights
10. Snow mode button
11. Seat heater switches
12. Cigarette lighter
13. TRAC OFFº switch
(two- wheel drive models)
14. Cruise control switch
15. Ignition switch
16. Tilt steering lock release lever
17. Tire pressure warning system reset
switch
Vehicles with automatic air conditioning controls (view B without navigation system)

'05 HIGHLANDER_U (L/O 0409)
35
2005 HIGHLANDER from Nov. '04 Prod. (OM48570U)
2. To remove the fuel tank cap, turn
the cap counterclockwise by 90 de-
grees (to the pressure point 1), and
then turn it an additional 30 degrees
(to point 2). Pause slightly before
removing it.
It is not unusual to hear a slight swoosh
when the cap is opened.3. The removed cap can be stored on
the back side of the fuel filler door.
Position the cap so that the hooks point
to the left and right, and set it in the
receptacle on the back side of the door.When installing the cap, turn the cap
clockwise until you hear a click. When
you hear the click, the cap is fully
closed.
If the cap is not installed securely, the
malfunction indicator lamp comes on.
Make sure the cap is tightened securely.
The indicator lamp goes off after driving
several times. If the indicator lamp does
not go off, contact your Toyota dealer as
soon as possible.
CAUTION

Make sure the cap is installed se-
curely to prevent fuel spillage in
the event of an accident.

Use only a genuine Toyota fuel tank
cap for replacement. It is designed
to regulate fuel tank pressure.
NOTICE
To prevent damage to the cap, apply
force only in the turning direction to
the cap. Do not pull or pry it.

'05 HIGHLANDER_U (L/O 0409)
171
2005 HIGHLANDER from Nov. '04 Prod. (OM48570U)
YOUR RADIO ANTENNA
Your vehicle has the mast type antenna or
on- glass antenna printed on the inside of
the rear quarter window.
Mast type antennaÐTo remove an anten-
na, carefully turn it counterclockwise.
NOTICE

Mast type antenna:
To prevent damage to the antenna,
make sure it is removed before
driving your Toyota through an au-
tomatic car wash.

On- glass antenna:
Attaching the film (especially con-
ductive or metallic type) on the rear
glass will noticeably reduce the
sensitivity of the radio.
YOUR CASSETTE PLAYER
When you insert a cassette, the exposed
tape should face to the right.
NOTICE
Do not oil any part of the player and
do not insert anything other than cas-
sette tapes into the slot, or the tape
player may be damaged.
YOUR COMPACT DISC PLAYER (type 1)
When you insert a disc, gently push it in
with the label side up. The player will play
from track 1 through to the end of the
disc. Then it will play from track 1 again.
NOTICE
Never try to disassemble or oil any
part of the compact disc player. Do
not insert anything other than com-
pact discs into the slot.
8 cm (3 in.) compact disc singles
Your compact disc player does not need
an adaptor to play compact disc singles.
Compact disc singles are about 8 cm (3
in.) in diameter- smaller than standard
discs.
After you eject a compact disc single, do
not insert a standard 12 cm (4.7 in.) disc
until DISCº disappears from the display.
NOTICE
Do not use an adaptor for compact
disc singles
Ðit could cause tracking
errors or interfere with the ejection of
compact discs.
YOUR COMPACT DISC PLAYER WITH
CHANGER (type 2)
When you insert a disc, push the LOADº
button and gently push the disc in with
the label side up. This compact disc play-
er can store up to six discs. The player
will play from track 1 through to the end
of the disc. Then it will play from track
1 of the next disc.
The player is intended for use with 12 cm
(4.7 in.) discs only.

2005 HIGHLANDER (EWD592U)
155
SRS
NOTICE: When inspecting or repairing the SRS, perform service in accordance with the following precautionary instructions
and the procedure, and precautions in the Repair Manual applicable for the model year.

Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the most important source of information
when troubleshooting. When troubleshooting the SRS, always inspect the DTCs before disconnecting the battery.

Work must be started more than 90 seconds after the ignition SW is turned to the ºLOCKº position and the
negative (-) terminal cable is disconnected from the battery.
(The SRS is equipped with a back-up power source so that if work is started within 90 seconds from
disconnecting the negative (-) terminal cable of the battery, the SRS may deploy.)

When the negative (-) terminal cable is disconnected from the battery, the memory of the clock and audio system will be
cleared. So before starting work, make a record of the contents in the audio memory system. When work is finished,
reset the audio systems as they were before and adjust the clock. Some vehicles have power tilt steering, power
telescopic steering, power seat and power outside rear view mirror which are all equipped with memory function.
However, it is not possible to make a record of these memory contents. So when the work is finished, it will be
necessary to explain it to your customer, and ask the customer to adjust the features and reset the memory. To avoid
erasing the memory in each system, never use a back-up power supply from outside the vehicle.

Before repair, remove the airbag sensor if shocks are likely to be applied to the sensor during repair.

Do not expose the following parts directly to hot air or flame;

Even in cases of a minor collision where the SRS does not deploy, the following parts should be inspected;

Never use SRS parts from another vehicle. When replacing parts, replace with new parts.

For the purpose of reuse, never disassemble and repair the following parts.

If the following parts have been dropped, or have cracks, dents and other defects in their case, bracket, and connector,
replace with new one.

Use a volt/ohmmeter with high impedance (10 kW/V minimum) for troubleshooting electrical circuits of the system.

Information labels are attached to the periphery of the SRS components. Follow the instructions of the notice.

After work on the SRS is completed, check the SRS warning light.

If the vehicle is equipped with a mobile communication system, refer to the precaution in the IN section of the Repair
Manual.
*Steering wheel pad
*Front passenger airbag assembly
*Side airbag assembly
*Curtain shield airbag assembly
*Seat belt pretensioner
*Center airbag sensor assembly
*Front airbag sensor assembly
*Side airbag sensor assembly

'05 HIGHLANDER_U (L/O 0409)
267
2005 HIGHLANDER from Nov. '04 Prod. (OM48570U)
3. Average fuel consumption
(AVG MPGº or AVG L/100 kmº)
Average fuel consumption is calculated
and displayed based on total driving
distance and total fuel consumption
with the engine running.
The displayed value is updated every 10
seconds.
4. Instantaneous fuel consumption
(MPGº or L/100 kmº)
The instantaneous fuel consumption is
calculated and displayed based on dis-
tance and fuel consumption for 1 sec-
onds with the engine running.
The displayed value is updated every 2
seconds.
Note that an accurate figure may not be
shown in the following cases.
The vehicle is stopped with the engine
running. (The display will indicate the
extremely high fuel consumption.)
The vehicle is driving down a long
slope applying the engine brake. (The
display will indicate the extremely low
fuel consumption.)
The calculation is reset when the ignition
switch is turned off.5. Driving time (E/Tº)
The elapsed time after the engine starts
is displayed.
When the engine is started, driving time
is counted from 0:00. Up to 11:59 (11
hours, 59 minutes) can be displayed.
When the driving time exceeds 11:59, the
counter returns to 0:00.
The calculation is reset when the ignition
switch is turned off.
To reset the hour: Push the Hº button.
To reset the minutes: Push the Mº button.
The key must be in the ACCº or ONº
position.
If the electrical power source has been
disconnected from the clock, the time dis-
play will automatically be set to 1:00 (one
o'clock).
Clock

No. 4 Cylinder TDC/Compression
IN
EXA52470
Timing MarkPaint Mark
Timing Mark
Groove Paint Mark
A52471
A13325
- ENGINE MECHANICALVALVE CLEARANCE (2AZ-FE)
14-7
2500 Author
: Date
:
2005 HIGHLANDER REPAIR MANUAL (RM1144U)
Valve clearance (Cold):
ItemSpecified Condition
Intake0.19 to 0.29 mm (0.008 to 0.011 in.)
Exhaust0.30 to 0.40 mm (0.012 to 0.016 in.)
(b) Turn the crankshaft clockwise 1 revolution (360) and set
the No.4 cylinder to TDC/compression.
(c) Check only the valve indicated on the left.
(1) Using a feeler gauge, measure the clearance be-
tween the valve lifter and camshaft.
(2) Record valve clearance measurements that are out
of the specified range. These measurements will be
used later to determine the size of the adjustment
shim to be installed.
Valve clearance (Cold):
ItemSpecified Condition
Intake0.19 to 0.29 mm (0.008 to 0.011 in.)
Exhaust0.30 to 0.40 mm (0.012 to 0.016 in.)
12. ADJUST VALVE CLEARANCE
NOTICE:
Be sure not to turn the crankshaft without the chain ten-
sioner.
(a) Turn the crankshaft clockwise 1 revolution (360) and set
the No. 1 cylinder to the TDC/compression.
(b) Place paint marks on the timing chain and camshaft tim-
ing gear sprocket.
(c) Remove the 2 bolts and chain tensioner.

05IS7-02
I38587*1
*2*1
*2*3
*4
05-1768
- DIAGNOSTICSNAVIGATION SYSTEM
1958 Author
: Date
:
2005 HIGHLANDER REPAIR MANUAL (RM1144U)
DIAGNOSIS DISPLAY DETAILED DESCRIPTION
HINT:

This section contains a detailed description of displays within diagnostic mode.

Illustrations may differ from the actual vehicle depending on the device settings and options. There-
fore, some detailed areas may not be shown exactly the same as on the actual vehicle.
1. System Check
(a) System Check Mode Display
Device Names and Hardware Address/*1
HINT:

Registered device names are displayed below.

If a device name is unknown to the system, its physical address is shown instead.
Address No.NameAddress No.Name
11 0EMV120AV X
1281DIN TV140AV N
144G-BOOK178NAVI
17CMONET190AUDIO H/U
1ACCAMERA-C1B0Rr-TV
1C0Rr-CONT1C2TV-TUNER2
1C4PANEL1C6G/W
1C8FM-M-LCD1D8CONT-SW
1ECBody1F0RADIO TUNER
1F1XM1F2SIRIUS
230TV-TUNER240CD-CH2
250DVD-CH280CAMERA
360CD-CH13A0MD-CH
17DTEL440DSP-AMP
530ETC5C8MAYDAY
1A0DVD-P1C6CLOCK
1F4RSA1F6RSE
480AMP

B51847
Driving Axis
ClockwiseCounterclock-
wise
4 5 6 7 8
B51844
05-1924
- DIAGNOSTICSPOWER WINDOW CONTROL SYSTEM
2114 Author
: Date
:
2005 HIGHLANDER REPAIR MANUAL (RM1144U)
5 INSPECT POWER WINDOW REGULATOR MOTOR ASSY RH (PASSENGER SIDE)
(a) Inspect the operation of the front LH power window regu-
lator motor assembly.
(1) Check that the motor operates smoothly when the
battery voltage is applied to each terminal of the
connector.
Standard:
Measuring ConditionOperational Direction
Battery positive - Terminal 4
Battery negative - Terminal 5Clockwise rotation toward driving axis
Battery positive - Terminal 5
Battery negative - Terminal 4Counterclockwise rotation toward driving
axis
(b) Inspect the PTC operation inside the power window regulator motor.
NOTICE:
The inspection should be performed with the power window regulator and door glass installed to the
vehicle.
(1) Set a DC 400 A probe of the electrical tester in the wire harness of terminal 1 or 2.
NOTICE:
Match the arrow mark of the probe with the current direction.
(2) Set the door glass in the fully closed position.
(3) When 60 seconds have elapsed after the door glass is fully closed, check now long the current
takes to charge, from approximately 16 - 34 A into 1 A or less, when the power window switch
is turned UP once again.
Standard: Approximately 4 - 90 seconds
(4) When approximately 60 seconds have elapsed after the inspection of the current cut-off, check
that the door glass goes down when the power window regulator switch is turned DOWN.
OK REPAIR OR REPLACE HARNESS AND
CONNECTOR
NG REPLACE POWER WINDOW REGULATOR
MOTOR ASSY RH
6 CHECK POWER WINDOW REGULATOR SWITCH ASSY REAR (REAR RH AND LH)
(a) Inspect the power source voltage.
(1) Disconnect the regulator switch connector.
(2) Check the voltage between terminal 7 (+B) of the
regulator switch vehicle's side connector and the
body ground.
Standard: 10 - 14 V with ignition switch ON
NG REPAIR OR REPLACE HARNESS AND
CONNECTOR
OK

B51848
Driving Axis
Clockwise
Counterclockwise
05-1926
- DIAGNOSTICSPOWER WINDOW CONTROL SYSTEM
2116 Author
: Date
:
2005 HIGHLANDER REPAIR MANUAL (RM1144U)
9 INSPECT POWER WINDOW REGULATOR MOTOR ASSY RH (REAR RH)
(a) Inspect the operation of the power window regulator mo-
tor assy RH (Rear RH side).
(1) Check that the motor operates smoothly when the
battery voltage is applied to each terminal of the
connector.
Standard:
Measuring ConditionOperational Direction
Battery positive - Terminal 5
Battery negative - Terminal 4Clockwise rotation toward driving axis
Battery positive - Terminal 4
Battery negative - Terminal 5Counterclockwise rotation toward driving
axis
(b) Inspect the PTC operation inside the power window regulator motor.
NOTICE:
The inspection should be performed with the power window regulator and door glass installed to the
vehicle.
(1) Set a DC 400 A probe of the electrical tester in the wire harness of terminal 1 or 2.
NOTICE:
Match the arrow mark of the probe with the current direction.
(2) Set the door glass in the fully closed position.
(3) When 60 seconds have elapsed after the door glass is fully closed, check now long the current
takes to charge, from approximately 16 - 34 A into 1 A or less, when the power window switch
is turned UP once again.
Standard: Approximately 4 - 90 seconds
(4) When approximately 60 seconds have elapsed after the inspection of the current cut-off, check
that the door glass goes down when the power window regulator switch is turned DOWN.
OK REPAIR OR REPLACE HARNESS AND
CONNECTOR
NG REPLACE POWER WINDOW REGULATOR
MOTOR ASSY RH