belt TOYOTA LAND CRUISER 1986 Factory Owner's Manual

BO1LD-03
H18905
Rear Door Opening TrimRoof Headlining Rear Trim
Upper Roof Side
Inner Garnish
Quarter Trim Jack CoverStriker Plate
Quarter Trim Panel Rear Door Scuff PlateQuarter Belt MouldingRear Mat
Rear Mat Set Plate Quarter Window
GlassStriker Plate Quarter Window
Glass Weatherstrip
Striker Plate
x5 Rear
Assist Grip Rear Vent Window Motor
Assist Grip
Plug
Assist Grip
Plug
- BODYQUARTER WINDOW GLASS
BO-61
2635 Author
: Date
:
2004 LAND CRUISER (RM1071U)
QUARTER WINDOW GLASS
COMPONENTS

BO4IW-01
H05257
: 5 Clips
H05258
H05259
H07941
11 Clips BO-62
- BODYQUARTER WINDOW GLASS
2636 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ROOF HEADLINING REAR TRIM
Using a screwdriver, remove the roof headlining rear trim.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE REAR NO. 2 SEATS
3. REMOVE REAR MAT SET PLATE
(a) Remove the 5 screws.
(b) Using a screwdriver, remove the rear mat set plate.
HINT:
Tape up the screwdriver tip before use.
4. REMOVE STRIKER PLATE
(a) Remove the 6 screws.
(b) Using a screwdriver, remove the striker plates.
HINT:
Tape up the screwdriver tip before use.
5. REMOVE REAR MAT
6. REMOVE REAR NO. 2 SEAT OUTER BELT FLOOR AN-
CHOR
Torque:42 N´m (430 kgf´cm, 31 ft´lbf)
7. REMOVE REAR NO. 1 SEAT OUTER BELT FLOOR AN-
CHOR
Torque:42 N´m (430 kgf´cm, 31 ft´lbf)
8. REMOVE REAR DOOR SCUFF PLATE
9. REMOVE REAR DOOR OPENING TRIM
10. REMOVE QUARTER TRIM PANEL
(a) Remove the quarter trim jack cover.
(b) Using a clip remover, remove the 2 clips.
(c) Remove the quarter trim panel, then disconnect the con-
nector.
11. REMOVE REAR NO. 2 SEAT OUTER BELT SHOUL-
DER ANCHOR
12. REMOVE REAR NO. 1 SEAT OUTER BELT SHOUL-
DER ANCHOR

H18906
: 9 Clips
H04108
H05403
Quarter Belt
Moulding
Clip
: 4 Clips
H04110
- BODYQUARTER WINDOW GLASS
BO-63
2637 Author
: Date
:
2004 LAND CRUISER (RM1071U)
13. REMOVE UPPER ROOF SIDE INNER GARNISH
(a) Using a screwdriver, remove the assist grip plugs, then re-
move the 2 screws and the rear assist grip.
HINT:
Tape up the screwdriver tip before use.
(b) Using a clip remover, remove the clip.
(c) Using a screwdriver, remove the upper roof side inner gar-
nish.
HINT:
Tape the screwdriver tip before use.
14. REMOVE QUARTER WINDOW GLASS
(a) Disconnect the connector.
(b) w/ Antenna:
Disconnect the connector.
(c) Remove the 2 bolts, the 2 nuts and the quarter window
glass.
15. REMOVE QUARTER WINDOW GLASS WEATH-
ERSTRIP
16. REMOVE QUARTER BELT MOULDING
(a) Remove the screw.
(b) Using a screwdriver, remove the quarter belt moulding.
HINT:
Tape up the screwdriver tip before use.
17. REMOVE REAR VENT WINDOW MOTOR
Remove the screw and the rear vent window motor.
18. REMOVE QUARTER WINDOW LOCK
Remove the screw and the quarter window lock.

BO1JE-03
H20973
Quarter Window Glass
with WeatherstripDivision Bar
Door Glass Run
Door Glass Door Belt Moulding
Service Hole Cover
Door Inside
Handle Bezel No. 1Inside Handle
Power Window
Switch Door Lock Outside Handle
Window Regulator
Door Courtesy Light
Door TrimDoor CheckDoor Hinge
Speaker
Door Hinge
: Specified torque
N´m (kgf´cm, ft´lbf)

Precoated part
27 (275, 20)
26 (265, 19)
5.0 (51, 44 in.´lbf)

8.0 (82, 71 in.´lbf)
26 (265, 19)
8.0 (82, 71 in.´lbf)
Door Inside
Handle Bezel No. 2
Door Check
Cover
23 (235, 17)
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
8.0 (82, 71 in.´lbf)
23 (235, 17)
BO-14
- BODYREAR DOOR
2588 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REAR DOOR
COMPONENTS

H21409
H04823
H04824
H04825
H04826
BO-16
- BODYREAR DOOR
2590 Author
: Date
:
2004 LAND CRUISER (RM1071U)
6. REMOVE INSIDE HANDLE
(a) Remove the screw and the inside handle.
(b) Disconnect the 2 control cables from the inside handle as
shown in the illustration.
7. REMOVE SPEAKER
Remove the 3 screws and speaker, then disconnect the con-
nector.
8. REMOVE SERVICE HOLE COVER
(a) Remove the clamps and wire harness.
(b) Remove the service hole cover.
NOTICE:
Do not tear the cover.
HINT:
At the time of reassembly, bring out the 2 control cables and
wire harness through the service hole cover.
9. REMOVE DOOR BELT MOULDING
Using a scraper, remove the door belt moulding.
HINT:
Tape up the scraper tip before use.
10. REMOVE DOOR GLASS RUN
11. REMOVE DIVISION BAR
Remove the 2 bolts, screw and division bar.
12. REMOVE DOOR GLASS
Disconnect the glass from the regulator arm and remove the
door glass by pulling it upward.
13. REMOVE QUARTER WINDOW GLASS WITH WEATH-
ERSTRIP
14. REMOVE WINDOW REGULATOR
(a) Disconnect the connector, then remove the 3 bolts.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
(b) Loosen the bolt and window regulator.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
HINT:

Remove the regulator through the service hole.

BO1L0-05
H16046
Headrest
Headrest SupportRear Seat Shoulder
Belt CoverRear Seat
Shoulder Belt Guide
Rear Seat Outer Belt
Reclining Adjuster
Release Handle No. 1 Reclining Cover
Corner Pad
Rear No. 1
Seat Adjuster
Seat Adjuster
Control Cable Seatback Cover
Seatback Pad
Seatback Frame No. 1 ProtectorSeatback Board
Protector
Rear No. 1 Seat AdjusterReclining Inner Cover
Corner Pad
No. 1 Reclining Cover
Hinge
CoverSeat Cushion
Cover
Seat Cushion Pad
Seat Cushion FrameReclining Remote
Control Lever Knob
Hinge Cover
Fold Seat
Stopper Band
Armrest Seat Cushion
Under Cover
Lock Striker
Stay Cover
RH No. 1 Leg
StayLH No. 1 Leg Stay Rear Seat
StayRear Seat
Cushion HingeHinge Cover
Hinge CoverNo. 1 Fold Seat
Lock Control Cable
Seat
Lock
CoverRear Seat
Inner Belt
: Specified torque

Non-reusable part
Hog Ring

Hog Ring
42 (430, 31)
Armrest Hinge
Hinge Cover
41 (420, 30)
Hinge Cover
Rear Seat Lock
Bracket
Seat Cushion
Under Cover
Sub-Assembly
42 (430, 31)
C
41 (420, 30)
N´m (kgf´cm, ft´lbf) BO-1 18
- BODYREAR NO.1 SEAT (LH)
2692 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REAR NO.1 SEAT (LH)
COMPONENTS

H05321
H05329
H07957
H07940
H05324
- BODYREAR NO.1 SEAT (LH)
BO-121
2695 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Remove 10 screws and seat cushion under cover sub-
assembly.
7. REMOVE NO. 1 FOLD SEAT LOCK CONTROL CABLE
Remove the 2 clamps and No. 1 fold seat lock control cable as
shown in the illustration.
8. REMOVE RH NO. 1 SEAT LEG STAY
Using a screwdriver, remove the 2 E-rings and No. 1 seat leg
stay.
HINT:
Tape the screwdriver tip before use.
9. REMOVE RH REAR SEAT LOCK
(a) Remove the screw and rear seat lock cover.
(b) Remove the bolt, seat belt anchor and inner belt.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(c) Remove the RH rear seat lock.
10. REMOVE SEATBACK ASSEMBLY
(a) Remove the 3 screws and seat belt reclining detecting
part.
Torque: 3.9 N´m (40 kgf´cm, 35 in.´lbf)

H05730
A
H05325
H05326
H05327
H05331
BO-122
- BODYREAR NO.1 SEAT (LH)
2696 Author
: Date
:
2004 LAND CRUISER (RM1071U)
HINT:
At the time of reassembly, please refer to the following items.

Tighten the 2 screws on the seatback side.

Fold down the seatback forward and raise it up to the first
lock position.

Turn A to the rear side of the seat cushion for initial posi-
tioning.

Check visually that the reference holes are penetrated.

Tighten the screws on the cushion side of seat belt reclin-
ing detecting part.
(b) Loosen the nut, remove the reclining connecting wire of
LH side edge.
(c) Remove the reclining connecting wire of RH side edge.
(d) Remove the 4 bolts and seatback assembly.
Torque: 41 N´m (420 kgf´cm, 30 ft´lbf)
11. w/ Armrest:
REMOVE ARMREST
(a) Remove the 2 nuts and armrest.
(b) Remove the 2 screws and 2 hinge covers.
(c) Remove the 2 bolts and hinges.
12. REMOVE SEATBACK FRAME
(a) Using a screwdriver, remove the rear seat shoulder belt
cover.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 4 headrest supports.
(c) Disengage the hooks, remove the seatback frame.
13. REMOVE SEAT ADJUSTER CONTROL CABLE

H05332
H05333
H07956
- BODYREAR NO.1 SEAT (LH)
BO-123
2697 Author
: Date
:
2004 LAND CRUISER (RM1071U)
14. REMOVE REAR SEAT OUTER BELT
(a) Remove the 2 bolts and rear seat shoulder belt guide.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
HINT:
At the time of reassembly, please refer to the following item.
Install the shoulder belt guide to the seatback frame with a slit
the guide facing to the rear side of the vehicle.
(b) Remove the 2 nuts and rear seat outer belt.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
15. REMOVE NO. 1 PROTECTOR
16. REMOVE SEATBACK COVER
Remove the hog rings and seatback cover.
HINT:
At the time of reassembly, please refer to the following item.
When installing hog rings, take care to prevent wrinkles as little
as possible.
17. REMOVE SEAT CUSHION FRAME
Remove the hog rings and seat cushion frame.
HINT:
At the time of reassembly, please refer to the following item.
When installing hog rings, take care to prevent wrinkles as little
as possible.
18. REMOVE REAR NO. 1 SEAT ADJUSTER
(a) Remove the 2 bolts and rear No. 1 seat outer adjuster.
Torque: 41 N´m (420 kgf´cm, 30 ft´lbf)
(b) Remove the 2 bolts and rear No. 1 seat inner adjuster.
Torque: 41 N´m (420 kgf´cm, 30 ft´lbf)
(c) Remove the 2 hinge covers from the outer and inner ad-
juster.
19. REMOVE REAR SEAT STAY
Remove the 2 bolts and rear seat stay.
20. REMOVE LH NO. 1 SEAT LEG STAY
Using a screwdriver, remove the spring nut, E-ring and LH No.
1 seat leg stay.
21. REMOVE REAR SEAT CUSHION HINGE
(a) Using a screwdriver, remove the spring nut and E-ring.
(b) Remove the 2 hinge pins, 2 cushion spacers, 2 cushion
support springs and 2 rear seat cushion hinges.
22. REMOVE LH REAR SEAT LOCK
Unfasten the bolt, then remove the inner belt and LH rear seat
lock.

BO1L5-05
H07958
Headrest
Headrest Support
Seatback Cover Seatback Pad
Seatback Frame No. 1 ProtectorSeatback BoardNo. 1 Reclining Cover
Corner Pad No. 1 Seat Adjuster
Rear No. 1
Seat Inner Belt Reclining
Inner
Cover
Hinge Cover
Reclining Inner CoverReclining
Connecting Wire
No. 1 Seat
Adjuster
Hinge Cover
No. 1
Reclining
Cover Corner Pad
Reclining Adjuster
Release HandleSeat Cushion
Under Cover
Seat Cushion
Under CoverSeat Cushion
Under Cover
Sub-Assembly
Rear Seat
Lock Striker Cover Fold Seat
Stopper Band
No. 1 Seat Leg StaySeat Leg Rear Seat
Lock
No. 2 Fold Seat
Lock Control CableLock Cover
Reclining Remote
Control Lever Knob
: Specified torque
N´m (kgf´cm, ft´lbf)

Non-reusable part

Hog Ring
Hinge Cover
Cushion

Hog Ring
Seat Cushion Cover
Seat Cushion Pad
Seat Cushion Frame
37 (380, 27)
41 (420, 30)
37 (380, 27)
BO-126
- BODYREAR NO.1 SEAT (RH)
2700 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REAR NO.1 SEAT (RH)
COMPONENTS