warning light TOYOTA LAND CRUISER 1986 Factory Manual PDF

DI3BR-05
D13102
Combination Meter
DLC3 Stop Light SwitchECM
Transmission Control
Switch
(2 e L Position)
Pattern Select Switch
Park/Neutral Position Switch
Speed Sensor SP2
Shift Solenoid Valve S1
Shift Solenoid Valve SR
Shift Solenoid Valve SLU
Shift Solenoid Valve SL2 ATF Temperature
Sensor No. 2Speed Sensor NT
Indicator Switch
(Transfer Neutral Position Switch)
Indicator Switch
(Transfer L4 Position Switch)
Transmission Control
Switch
(D e 4 Position)
MIL

ECT PWR Indicator Light

2nd STRT Indicator Light

A/T. P. Indicator Light
Shift Solenoid
Valve SL1
Shift Solenoid
Valve SLT
ATF Temperature
Sensor No. 1
Shift Solenoid Valve S2

AT Oil Temp warning Light DI-392
- DIAGNOSTICSAUTOMATIC TRANSMISSION
585 Author
: Date
:
2004 LAND CRUISER (RM1071U)
PARTS LOCATION

- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-397
590 Author
: Date
:
2004 LAND CRUISER (RM1071U) Shift point too high or too low
1. Shift solenoid valve (SLT) circuit *1
2. Speed sensor NT circuit *1
3. Speed sensor SP2 circuit *1
4. Throttle position sensor circuit *1
5. ATF temperature sensor circuit *1
6. Pattern select switch circuit (PWR mode switch)
7. Transfer L4 position switch circuit *1
8. ECM
DI-479
DI-418
DI-421
DI-36
DI-410
DI-495
DI-472
IN-36
Up-shift to 5th from 4th while shift lever is 4 position1. Transmission control switch circuit (D - 4) *1
2. ECM
DI-402
IN-36
Up-shift to 5th from 4th while engine is cold1. Engine coolant temp. sensor circuit *1
2. ECM
DI-36
IN-36
Up-shift to 4th from 3rd while shift lever is 3 position1. Park/neutral position switch circuit *1
2. ECM
DI-402
IN-36
Up-shift to 3rd from 2nd while shift lever is 2 position1. Park/neutral position switch circuit *1
2. ECM
DI-402
IN-36
Up-shift to 2nd from 1st while shift lever is L position1. Transmission control switch circuit (2 - L) *1
2. ECM
DI-402
IN-36
Harsh engagement (N " D)
1. Speed sensor NT circuit *1
2. Shift solenoid valve (SL1) circuit *1
3. Shift solenoid valve (SLT) circuit *1
4. ECM
DI-418
DI-426
DI-479
IN-36
Harsh engagement (Lock-up)
1. Speed sensor NT circuit *1
2. Speed sensor SP2 circuit *1
3. Shift solenoid valve (SLU) circuit *1
4. ECM
DI-418
DI-421
DI-491
IN-36
Harsh engagement (Any driving position)ECMIN-36
Poor acceleration1. ATF temperature sensor No.2 circuit *1
2. ECM
DI-483
IN-36
No engine brakingECMIN-36
No kick-downECMIN-36
Engine stalls when starting off or stoppingECMIN-36
No pattern select (PWR)1. Pattern select switch circuit (PWR mode switch)
2. ECMDI-495
IN-36
No 2nd start
1. Pattern select switch circuit (2nd start switch)
2. Transmission control switch circuit (2 - L) *1
3. ECM
DI-497
DI-402
IN-36
AT Oil Temp. warning light remains on*1Lock-up at 3rd gear1. ATF temperature sensor No.2 circuit *1
2 ECM
DI-483
IN 36Shift point too high2. ECMIN-36
A/T.P. indicator light does not light up
1. A/T.P. indicator light circuit
2. Combination meter circuit
3. ECMDI-500
BE-58
IN-36

H21247
Airbag Sensor
Assembly
C26IG2 5
B-R
3F3 IGN
3E4Cowl Side J/B RH
AB-R
AJ4
J/C
B-R
6 7
W-RCowl Side J/B LH
2E
2A 41 10
BatteryF15
FL Block
MAINB-G Engine Room J/B
1C 1B1 9AM2
W-R I18
Ignition SW
2 AM2 IG2
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-923
111 6 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DTC Normal Source Voltage Drop
CIRCUIT DESCRIPTION
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in
case the source voltage drops.
When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the
voltage of the SRS to normal voltage.
The diagnosis system malfunction display for this circuit is differ from the other circuits in that when the SRS
warning light remains on and the DTC shows a normal code, source voltage drop is indicated.
Malfunction in this circuit is not recorded in the airbag sensor assembly, and when the source voltage returns
to normal, the SRS warning light automatically goes off.
DTC No.Diagnosis
(Normal)Source voltage drop
WIRING DIAGRAM
DI8FC-09

H01249
ON
DI-926
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
111 9 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4 Does SRS warning light turn off?
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Connect the steering wheel pad connector.
(c) Connect the front passenger airbag assembly connector.
(d) w/ Side airbag:
Connect the side airbag assembly connectors.
(e) Connect the seat belt pretensioner connectors.
(f) Connect the airbag sensor assembly connectors.
(g) Connect the front airbag sensor connectors.
(h) w/ Side airbag:
Connect the side and curtain shield airbag sensor assem-
bly connectors.
(i) w/ Side airbag:
Connect the curtain shield airbag assembly connectors.
(j) w/ Side airbag:
Connect the curtain shield airbag sensor assembly con-
nectors.
(k) Connect the seat position sensor assembly connector.
(l) Connect the front seat inner belt LH connector.
CHECK:
(a) Turn the ignition switch to ON.
(b) Operate electric system (defogger, wiper, headlight, heat-
er blower, etc.) and check that SRS warning light goes off.
NO Check for DTCs. If a DTC is output, perform trou-
bleshooting for the DTC. If a normal code is out-
put, replace airbag sensor assembly.
YES
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.

H21248
BatteryAirbag Sensor
Assembly
B-Y
LA
IG2 AM2
W-R41 Combination Meter
1011
3Q8
2A 2EB-Y
3F
C14Cowl Side J/B RH
MET
B-RC26
63
4
3E 7
3Q 4
C12 A/B
10
MAIN 2A
J4
J/C SB
B-G Cowl Side J/B LH
Engine Room J/B
1
1B1C 9AM23E 11 D7
DLC3
11
F15
FL Block W-R
7B-R
AA SRSSB
I18
Ignition SW
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-927
1120 Author
: Date
:
2004 LAND CRUISER (RM1071U)
SRS Warning Light Circuit Malfunction
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light comes on for approx. 6 seconds after the ignition switch
is turned from the LOCK position to ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to inform the driver of the abnormality.
When terminal TC and CG of the DLC3 are connected, the DTC is indicated by blinking the SRS warning
light.
WIRING DIAGRAM
DIB45-01

AB0117H01293H01295
Airbag Sensor Assembly
LOCK
DI-928
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1121 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
Always lights up, when ignition switch is in LOCK position.
1 Prepare for inspection (See step 1 on page DI-923).
2 Does SRS warning light turn off?
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Disconnect the airbag sensor assembly connector.
(d) Connect the negative (-) terminal cable to the battery.
CHECK:
Check operation of SRS warning light.
NO Check combination mater (See page BE-2).
YES
Replace airbag sensor assembly.

N14677
Fuse
AB0119H01300
H01301
Airbag Sensor Assembly
ON
LA
(+)
(-)
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-929
1122 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Does not light up, when ignition switch is turned to ON.
1 Check AM2 Fuse.
PREPARATION:
Remove the AM2 fuse.
CHECK:
Check continuity of the AM2 fuse.
OK:
Continuity
HINT:

Fuse may be burnt out even if it appears to be OK during
visual inspection.

If fuse is OK, install it.
NG Go to step 5.
OK
2 Prepare for inspection (See step 1 on page DI-923).
3 Check SRS warning light circuit.
PREPARATION:
Connect the negative (-) terminal cable to the battery, and wait
at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and LA of
the airbag sensor assembly connector.
OK:
Voltage: 10 - 14 V
NG Check SRS warning light bulb or repair SRS
warning light circuit.
OK

AB0119H20916H21236
H21527
Airbag
Sensor
Assembly
Side and Curtain Shield
Airbag Sensor RH (*1)
Side Squib RH (*1)
P Squib
D Squib
Spiral
Cable
Front Airbag
Sensor RH
Front Airbag
Sensor LH
Curtain Shield
Squib LH (*1)
Side and Curtain Shield
Airbag Sensor LH (*1)
Side Squib LH (*1)
Curtain Shield
Squib RH (*1)
Curtain Shield Airbag
Sensor Assembly LH (*1)Curtain Shield Airbag
Sensor Assembly RH (*1)
ON
Seat Position
Sensor Assembly
P/T Squib RH
P/T Squib LH Front Seat Inner Belt
*1: w/ Side Airbag
DI-930
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1123 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4 Does SRS warning light come on?
PREPARATION:
(a) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(b) Connect the airbag sensor assembly connector.
(c) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON.
(b) Check operation of the SRS warning light.
NO Replace airbag sensor assembly.
YES
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use simulation method to check.

- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-931
1124 Author
: Date
:
2004 LAND CRUISER (RM1071U)
5 Is new AM2 fuse burnt out again?
NO Using simulation method, reproduce malfunc-
tion symptoms (See page IN-26).
YES
Check harness between AM2 fuse and SRS
warning light.

H21249
Airbag Sensor
Assembly
Cowl Side J/B RH
C2619
TC 3F10
2D18 P-B
W-BP-B D7
DLC3
3E 14
7B5
W-B 13
4 CGTC
IF 7B4 J/B No. 7
P-B DI-932
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1125 Author
: Date
:
2004 LAND CRUISER (RM1071U)
TC Terminal Circuit
CIRCUIT DESCRIPTION
DTC output mode is set by connecting terminal TC and CG of the DLC3 the airbag sensor assembly.
The DTCs are displayed by blinking the SRS warning light.
WIRING DIAGRAM
DIB46-02