warning lights TOYOTA LAND CRUISER 1986 Factory Repair Manual

BE2EF-01
1
2
3
4
5
6
7
8
9
1012
13
14
15
16
17
18
19
20 1120
19
18
17
16
15
14
13
12
1110
9
8
7
6
5
4
3
2
11
2
3
4
5
6
7
8
9
1012
13
14
15
16
17
18
19
20 11
20
19
18
17
16
15
14
13
12
1110
9
8
7
6
5
4
3
2
1
I29077
Connector C15 Connector C14 Connector C13 Connector C12
- BODY ELECTRICALCOMBINATION METER
BE-63
2436 Author
: Date
:
INSPECTION
1. INSPECT COMBINATION METER CIRCUIT
Connect the connector C12, C13, C14 and C15 to the combina-
tion meter and inspect the wire harness side connectors from
the back side as shown in the table.
Tester connectionConditionSpecified condition
C12 3 (DOOR ) G dEither door is openedBelow 1 VC12-3 (DOOR-) - GroundEither door is closed10 - 14 V
C12 4 (TURN L) G d
Ignition switch ON and
turn signal switch OFF or RIGHTBelow 1 V
C12-4 (TURN-L) - GroundIgnition switch ON and
turn signal switch LEFTPulse signal is output
10 - 14 V eBelow 1 V
C12 5 (BEAM ) G dIG switch ON, light control switch OFFBelow 1 VC12-5 (BEAM+) - GroundIG switch ON, light control switch ON10 - 14 V
C12 6 (TURN R) G d
Ignition switch ON and
turn signal switch OFF or LEFTBelow 1 V
C12-6 (TURN-R) - GroundIgnition switch ON and
turn signal switch RIGHTPulse signal is output
10 - 14 V eBelow 1 V
C12-7 (BEAM-) - GroundIG switch ON, light control switch ONBelow 1 V
C12 10 (CHG ) G dIgnition switch OFFBelow 1 VC12-10 (CHG+) - GroundIgnition switch ON10 - 14 V
C12 12 (ABS) G d
Ignition switch ON and ABS warning light lights
upBelow 1 V
C12-12 (ABS) - GroundIgnition switch ON and
ABS warning light does not light up10 - 14 V
C13 8 (ILL ) G dIG switch OFFBelow 1 VC13-8 (ILL+) - GroundIG switch ON10 - 14 V

BE-64
- BODY ELECTRICALCOMBINATION METER
2437 Author
: Date
:
C13 1 1 (CHECK E/G) G dIgnition switch ON and engine is stoppedBelow 1 VC13-1 1 (CHECK E/G) - GroundIgnition switch ON and engine is running10 - 14 V
C13-14 (CTR DIFF/4WD) - GroundIgnition switch ON and
center diff. lock switch OFFBelow 1 V
C13-14 (CTR DIFF/4WD) - GroundIgnition switch ON and
center diff. lock switch ON10 - 14 V
C13 15 (SLIP) G dIG switch ON, SLIP warning light ONBelow 1.5 VC13-15 (SLIP) - GroundIG switch ON, SLIP warning light OFF10 - 14 V
C13 16 (VSC TRC) G dIG switch ON, VSC TRC indicator light ONBelow 1.5 VC13-16 (VSC TRC) - GroundIG switch ON, VSC TRC indicator light OFF10 - 14 V
C13 17 (VSC OFF) G dIG switch ON, VSC OFF indicator light ONBelow 1.5 VC13-17 (VSC OFF) - GroundIG switch ON, VSC OFF indicator light OFF10 - 14 V
C13 18 (ACTIVE TRC) G dIG switch ON, TRC OFF indicator light ONBelow 1.5 VC13-18 (ACTIVE TRC) - GroundIG switch ON, TRC OFF indicator light OFF10 - 14 V
C13 19 (RSCA OFF) G dIG switch ON, RSCA warning light ONBelow 2.0 VC13-19 (RSCA OFF) - GroundIG switch ON, RSCA warning light OFF10 - 14 V
C14-4 (AIR BAG-) - GroundIgnition switch ON and
SRS indicator light lights upBelow 1 V
C14-4 (AIR BAG-) - GroundIgnition switch ON and
SRS indicator does not light up10 - 14 V
C14 7 (OIL PRS SDR) G dIgnition switch ON and indicator ONBelow 1 VC14-7 (OIL PRS SDR) - GroundIgnition switch ON and indicator OFF10 - 14 V
C14-10 (T/M PULSE) - GroundEngine is RunningPulse generation
C14 1 1 (D BKL SW) G dIgnition switch ON and seat belt is unfastened10 - 14 VC14-1 1 (D-BKL SW) - GroundIgnition switch ON and seat belt is fastenedBelow 1 V
C14 18 (PKB SW) G d
Ignition switch ON and
parking brake lever is pulledBelow 1 V
C14-18 (PKB SW) - GroundIgnition switch ON and
parking brake lever is released10 - 14 V
C14 20 (BRAKE) G d
Ignition switch ON and brake system indicator
ONBelow 1 V
C14-20 (BRAKE) - GroundIgnition switch ON and brake system indicator
OFF10 - 14 V
C15-1 (E/G EARTH) - GroundConstantContinuity
C15-2 (MAIN FE) - GroundConstantContinuity
C15-4 (MAIN FV) - GroundIgnition switch ON4.5 - 5.5 V
C15 6 (MAIN FR) G d
Ignition switch ON and
fuel sender gauge float UPApprox. 0.5 V
C15-6 (MAIN FR) - GroundIgnition switch ON and
fuel sender gauge float DOWNApprox. 5.5 V
C15 7 (ILL ) G d
Ignition switch ON and
light control rheostat volume minimumBelow 1 V
C15-7 (ILL-) - GroundIgnition switch ON and
light control rheostat volume maximum10 - 14 V
Key unlock warning switch ON (Key is inserted)Below 1 V
C15-9 (KEY SW) - GroundKey unlock warning switch OFF
(Key is removed)10 - 14 V

I06184
F
1/2
E 321
- BODY ELECTRICALCOMBINATION METER
BE-67
2440 Author
: Date
:
6. INSPECT FUEL SENDER GAUGE VOLTAGE
(a) Apply voltage (4.5 V - 5.0 V) between terminals 2 and 3.
(b) Measure voltage between terminals 1 and 2 for each float
position.
Float position mm (in.)Voltage (V)
F: Approx. 85.3 (3.36)Approx. 4.60 ± 0.1
1/2: Approx. 1.7 (0.67)Approx. 2.45 ± 0.1
E: Approx. 91.9 (3.62)Approx. 0.30 ± 0.1
If voltage value is not as specified, replace main sender gauge.
7. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the low oil pressure
switch.
(b) Turn the ignition switch ON.
(c) Connect the terminal of wire harness side connector and
ground, then check the warning light.
8. INSPECT PARKING BRAKE WARNING LIGHT
(a) Disconnect the connector from the parking brake switch
and ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
9. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connector from the brake fluid level warn-
ing switch and ground terminal on the wire harness side
connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
10. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
(a) Remove the reservoir tank cap and retainer.
(b) Disconnect the connector.
(c) Check that the continuity exists between the terminal.
(d) Use syphon, etc., to take fluid out of the reservoir tank.
(e) Check that the continuity exists between terminals.
(f) Pour the fluid back in the reservoir tank.
11. INSPECT OPEN DOOR WARNING LIGHT
(a) DIsconnect the connector from the driver door courtesy
switch and ground terminal on the wire harness side con-
nector.
(b) Turn the ignition switch ON and check that the warning
light lights up.

I24949
12 1
11 Connector C15 Connector C14
I24950
12 1
9
10Connector C15
I04107
12
4
OFF
ON
I04108
Wire Harness Side: BE-68
- BODY ELECTRICALCOMBINATION METER
2441 Author
: Date
:
12. INSPECT SEAT BELT WARNING BUZZER
(a) Disconnect the connector from the combination meter.
(b) Connect the positive (+) lead from the battery terminal 12
and negative (-) lead terminal 1.
(c) Check that the buzzer stop after 4 to 8 seconds.
(d) Check that the buzzer stops when connecting the termi-
nal 11 to the GND.
13. INSPECT KEY UNLOCK WARNING BUZZER
(a) Disconnect the connector from the combination meter.
(b) Connect the positive (+) lead from the battery terminal 12
and negative (-) lead terminal 1.
(c) Connect the negative (-) lead from battery terminal 9 and
10, check that the buzzer sound.
14. INSPECT SEAT BELT WARNING LIGHT
(a) DIsconnect the connector from the seat belt buckle switch
and ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
15. INSPECT SEAT BELT BUCKLE SWITCH CONTINUITY
Tester connectionBelt fastened
(Belt unfastened)
Seat belt buckle SW (D)1 - 4ON (OFF)
Seat belt buckle SW (P)2 - 4OFF (ON)
If operation is not as specified, replace the switch.
16. INSPECT SEAT BELT BUCKLE SWITCH CIRCUIT
Disconnect the switch connector and inspect the connector on
wire harness side, as shown.

BE0RO-03
I01256
1 2 3 4
5 6 7 8 LOCKACC
ON
START
I06372
N20125
1 2 OFF
ON
- BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE-29
2402 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. INSPECT IGNITION SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK-No continuity
ACC2 - 3Continuity
ON2 - 3 - 4
6 - 7Continuity
START1 - 2 - 4
6 - 7 - 8Continuity
If continuity is not as specified, replace the switch.
2. INSPECT IGNITION KEY ILLUMINATION OPERATION
Connect the positive (+) lead from the battery to terminal 1 and
the negative (-) lead to terminal 2, and check that the indicator
light lights up.
If operation is not as specified, replace the switch.
3. INSPECT KEY UNLOCK WARNING SWITCH CONTI-
NUITY
Switch positionTester connectionSpecified condition
OFF (Key removed)-No continuity
ON (Key set)1 - 2Continuity
If continuity is not as specified, replace the switch.
Connect the switch connector and inspect the connector on
wire harness side from the back side, as shown.

BE-6
- BODY ELECTRICALTROUBLESHOOTING
2379 Author
: Date
:
2004 LAND CRUISER (RM1071U) Rear washer motor does not operate.
1. Rear Washer Motor
2. Rear Washer Switch
3. Wire HarnessBE-52
BE-52
-
Washer fluid does not operate.1. Washer Hose and Nozzle-
*1: Inspect wiper arm and blade set positions.
COMBINATION METER (Meter Gauges and Illumination):
SymptomSuspect AreaSee page
Tachometer, fuel gauge and engine coolant temperature gauge do
not operate.1. GAUGE2 Fuse
2. Combination Meter
3. Wire Harness-
BE-58
-
Speedometer does not operate.
1. Speed Sensor
2. Combination Meter
3. Wire HarnessBE-63
BE-58
-
Tachometer does not operate.
1. Igniter
2. Combination Meter
3. Wire HarnessIG-1
BE-58
-
Fuel gauge does not operate or is in abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Combination Meter
4. Wire HarnessBE-63
BE-63
BE-58
-
Oil pressure gauge does not operate.
1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Combination Meter
4. Wire HarnessBE-63
BE-63
BE-58
-
Voltmeter does not operate.
1. Voltmeter
2. Combination Meter
3. Wire HarnessBE-63
BE-58
-
Engine coolant temperature gauge does not operate or is in ab-
normal operation
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Combination Meter
4. Wire HarnessBE-63
BE-63
BE-58
-
All illumination lights do not light up.1. Light Control Rheostat
2. Wire HarnessBE-63
-
Brightness does not change even when rheostat is turned.1. Bulb
2. Wire Harness-
-
Only one illumination light does not light up.1. Bulb
2. Wire Harness-
-
COMBINATION METER (Warning Light):
SymptomSuspect AreaSee page
Warning lights do not light up. (Except discharge, open door and
SRS)1. GAUGE1 Fuse
2. Combination Meter
3. Wire Harness-
BE-58
-
Fuel level warning light does not light up.
1. LED
2. Combination Meter
3. Fuel Sender Gauge
4. Wire Harness-
BE-58
BE-63
-
ABS warning light does not light up.
1. LED
2. ABS ECU
3. Wire Harness-
DI-502
-

- BODY ELECTRICALTROUBLESHOOTING
BE-7
2380 Author
: Date
:
2004 LAND CRUISER (RM1071U) Seat belt warning light does not light up.
1. LED
2. Seat Belt Buckle Switch
3. Wire Harness
4. Body ECU-
BE-63
BE-63
DI-1038
Discharge warning light does not light up.
1. METER Fuse
2. LED
3. Wire Harness
4. Generator-
-
-
CH-2
Brake warning light does not light up.
1. LED
2. Parking Brake Switch
3. Brake Fluid Level Warning Switch
4. LED Check Relay
5. Combination Meter
6. Wire Harness-
BE-63
BE-63
BE-63
BE-58
-
SRS warning light does not light up.
1. ECU-B2 Fuse
2. LED
3. Airbag Sensor Assembly
4. Combination Meter
5. Wire Harness-
-
DI-690
BE-58
-
Open door warning light does not light up.
1. DOME Fuse
2. LED
3. Door Courtesy Switch
4. Combination Meter
5. Wire Harness-
-
BE-44
BE-58
-
A/T oil temperature warning light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-63
BE-58
DI-1
COMBINATION METER (Indicator Light):
SymptomSuspect AreaSee page
Cruise control indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-58
-
DI-1
High-beam indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. Headlight System-
BE-58
-
BE-30
Turn indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. Turn Signal and Hazard Warning System-
BE-58
-
BE-39
Shift indicator lights do not light up.
1. LED
2. Combination Meter
3. Park/Neutral Position Switch
4. Wire Harness-
BE-58
-
-
Only one shift indicator does not light up.1. LED
2. Combination Meter-
BE-58
Malfunction indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-58
-
DI-1

- BRAKETROUBLESHOOTING
BR-3
2139 Author
: Date
:
2004 LAND CRUISER (RM1071U) Noise from brakes
1. Pad (Cracked or distorted)
2. Installation bolt (Loose)
3. Disc (Scored)
4. Pad support plate (Loose)
5. Sliding pin (Worn)
6. Pad (Dirty)
7. Pad (Glazed)
8. Tension or return spring (Faulty)
9. Anti-squeal shim (Damaged)
10.Shoe hold-down spring (Damaged)BR-15
BR-24
BR-18
BR-27
BR-21
BR-30
BR-24
BR-27
BR-15
BR-24
BR-15
BR-24
BR-33
BR-15
BR-24
BR-33
Noise from hydraulic brake booster
(Abnormal pump motor operation noise)Accumulator bracket clearance (Out of adjustment)BR-66
Brake warning light lights up*1
(Parking brake pedal released)
1. Brake fluid level
2. Hydraulic brake booster power supply system (Faulty)-
BR-40
Brake warning light lights up and brake warning buzzer sounds*2Hydraulic brake booster power supply system (Faulty)BR-40
ABS warning light lights up*31. Anti - lock brake system (Faulty)
2. Hydraulic brake booster power supply system (Faulty)-
BR-40
*1, *3: The light may stay on for about 60 seconds after the engine is started. It is normal if it goes out after
a while.
*
2, *3: Depressing the brake pedal repeatedly may turn on the warning light and buzzer. It is normal if the
light goes off and the buzzer stops sounding after a few seconds.
*
3: While ABS warning light is ON.

Z03473
Ammeter
Disconnect Wire
from Terminal B
Battery
VoltmeterB
Generator CH-4
- CHARGINGCHARGING SYSTEM
1839 Author
: Date
:
2004 LAND CRUISER (RM1071U)
8. CHECK CHARGE WARNING LIGHT CIRCUIT
(a) Warm up the engine and then turn it off.
(b) Switch off all accessories.
(c) Turn the ignition switch ON, and check that the charge
warning light is lit.
(d) Start the engine, and check that the light goes off.
If the light does not go off as specified, troubleshoot the charge
light circuit.
9. INSPECT CHARGING CIRCUIT WITHOUT LOAD
HINT:
If a battery/generator tester is available, connect the tester to
the charging circuit as per manufacturer's instructions.
(a) If a tester is not available, connect a voltmeter and amme-
ter to the charging circuit as follows:

Disconnect the wire from terminal B of the genera-
tor, and connect it to the negative (-) tester probe
of the ammeter.

Connect the positive (+) tester probe of the amme-
ter to terminal B of the generator.

Connect the positive (+) tester probe of the voltme-
ter to terminal B of the generator.

Ground the negative (-) tester probe of the voltme-
ter.
(b) Check the charging circuit as follows:
With the engine running from idling to 2,000 rpm, check
the reading on the ammeter and voltmeter.
Standard amperage:
10 A or less
Standard voltage:
13.2 - 14.8 V
If the value is not specified, check the generator.
10. INSPECT CHARGING CIRCUIT WITH LOAD
(a) With the engine running at 2,000 rpm, turn on the high
beam headlights and place the heater blower switch at HI.
(b) Check the reading on the ammeter.
Standard amperage:
30 A or more
If the ammeter reading is less than the standard amperage, re-
pair the generator.
HINT:
If the battery is fully charged, the indication will sometimes be
less than standard amperage.
11. REINSTALL ENGINE UNDER COVER NO.1

F17763
EXI
WT A43
A43 IX1
F15Cowl Side J/B RH
Cowl Side J/B RH Cowl Side J/B RH
Cowl Side J/B LHI18
Ignition SW
Engine Room J/BCombination MeterABS & BA & TRAC
& VSC ECU
SB
D4
Detection SW
(Center Diff. Lock)
2
W-B
P-B
SB
SB
SB MET1
2
47
3E3Q
56 3
3Q
3B
3Q3B J4
J/C
B-R B-R
A
AP-B
L-R
W-R AM2 IG2
76
41 10
2E 2A
1
9
1C1B
2 B-G
ECFL Block
Battery MAIN
EC BR W-R8IX1
VSC OFF
17
C13 C12 C151
103
7
14 26
AM2 DI-624
- DIAGNOSTICSABS & VEHICLE STABILITY CONTROL (VSC) &
BRAKE ASSIST (BA) SYSTEM
817 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DTC Always ON Malfunction in ECU
VSC TRAC Warning Light Circuit
CIRCUIT DESCRIPTION
Always ONThere is a malfunction in the ECU internal circuit.

Power source circuit

Skid control ECU

VSC TRAC warning light circuit
HINT:
If the fail safe function is activated in the VSC system, ºVSC OFFº indicator light lights up.
WIRING DIAGRAM
DICA4-01