brake light TOYOTA LAND CRUISER 1998 Factory Repair Manual

B04203
B04204
IN-22
- INTRODUCTIONFOR ALL OF VEHICLES
22 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(d) Using Chassis Dynamometer:
Observe the following instructions and then measure with
the rear wheels.
(1) Remove the front propeller shaft.
(2) Put the center differential in LOCK position.
(3) If the vehicle is equipped with Vehicle Skid Control
(VSC) & Traction Control (TRAC) system, prohibit
the system from the activation (See step 2.).
(4) Ensure that the vehicle is securely fixed.
HINT:
Sudden shifting, braking, acceleration or deceleration is
not allowed.
Do not forget to change the Vehicle Skid Control (VSC) &
Traction Control (TRAC) system to operational condition
after the test. Check that the VSC warning indicator light
goes off when restarting the engine.
(e) On-V ehicle Wheel Balancing:
When doing on-vehicle wheel balancing on a full-time
4WD vehicle, to prevent each wheel from being rotated at
different speed in different directions (which could dam-
age the center differential), always be sure to observe the
following precautions.
(1) All of 4 wheels should be jacked up, being apart
from the ground completely.
(2) Put the center differential in LOCK position.
(3) If the vehicle is equipped with Vehicle Skid Control
(VSC) & Traction Control (TRAC) system, prohibit
the system from the activation (See step 2.).
(4) The parking brake lever should be fully released.
(5) None of the brakes should be applied.
(6) The wheels should be driven on the wheel balancer
with the engine running.
(7) Carry out the wheel balancing with the transmission
position in D position.
HINT:
When doing this balancing, pay attention to the other
wheels rotating at the same time.
Sudden acceleration, deceleration or braking is not al-
lowed.
Do not forget to change the Vehicle Skid Control (VSC) &
Traction Control (TRAC) system to operational condition
after the test. Check that the VSC warning indicator light
goes off when restarting the engine.

MA0055
MA02T-02
- MAINTENANCEBRAKE
MA-7
55 Author
: Date
:
2004 LAND CRUISER (RM1071U)
BRAKE
INSPECTION
1. INSPECT BRAKE LINE PIPES AND HOSES
HINT:
Check in a well lighted area. Check the entire circumference
and length of the brake hoses using a mirror as required. Turn
the front wheels fully right or left before checking the front brake.
(a) Check the all brake lines and hoses for damage.
(b) Check the all brake lines and hoses for wear.
(c) Check the all brake lines and hoses for deformation.
(d) Check the all brake lines and hoses for cracks.
(e) Check the all brake lines and hoses for corrosion.
(f) Check the all brake lines and hoses for leaks.
(g) Check the all brake lines and hoses for bends.
(h) Check the all brake lines and hoses for twists.
(i) Check all clamps for tightness and connections for leak-
age.
(j) Check that the hoses and lines are clear of sharp edges,
moving parts and the exhaust system.
(k) Check that the lines installed in grommets pass through
the center of the grommets.
2. INSPECT FRONT AND REAR BRAKE PADS AND
DISCS
(FRONT PADS: See page BR-16)
(REAR PADS: See page BR-25)
(FRONT DISCS: See page BR-21)
(REAR DISCS: See page BR-30)
3. INSPECT PARKING BRAKE LININGS AND DRUMS
(See page BR-36)

B04933
New Gasket
B04934
Fulcrum
Length
30 cm
SST
B04895
SST Fulcrum
Length
30 cm
B02714
CORRECT
WRONG
Delivery Pipe O-Ring
- SFISFI SYSTEM
SF-3
1702 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) When connecting the union bolt (fuel pressure pulsation
damper) on the high pressure pipe union, follow the pro-
cedure below:
(1) Always use 2 new gaskets.
(2) Tighten the union bolt by hand.
(3) Using SST, tighten the union bolt to the specified
torque.
SST 09612-24014 (09617-24011)
Torque:
33 N´m (340 kgf´cm, 24 ft´lbf) for use with SST
39 N´m (400 kgf´cm, 29 ft´lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
(c) When connecting the flare nut on the high pressure pipe
union, follow the procedure below:
(1) Apply a light coat of engine oil to the flare nut, and
tighten the flare nut by hand.
(2) Using SST, tighten the flare nut to the specified
torque.
SST 09023-12700
NOTICE:
Do not rotate the fuel filter outlet when tightening the flare
nut.
Torque:
34 N´m (345 kgf´cm, 25 ft´lbf) for use with SST
38 N´m (380 kgf´cm, 28 ft´lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
(d) Take following precautions to remove and install the injec-
tors.
(1) Never reuse the O-ring.
(2) When placing a new O-ring on the injector, take
care not to damage it.
(3) Coat a new O-ring with spindle oil or gasoline be-
fore installing; never use engine, gear or brake oil.