Jack TOYOTA LAND CRUISER 1998 Factory Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1998, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 1998Pages: 3115, PDF Size: 54.88 MB
Page 121 of 3115
AT147-03
D13650
Refill Plug
Overflow Plug
D14352
Overflow Tube
AT-3-1
- AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION SYSTEM
1855 Author: Date:
2004 LAND CRUISER (RM1071U)
AUTOMATIC TRANSMISSION
FLUID
OPERATION
1. BEFORE TRANSMISSION FILL
This transmission requires Toyota Genuine ATF WS.
It is necessary to refill the transmission with the correct
amount of fluid.
The vehicle must remain level while adjusting the trans-
mission fluid level.
On vehicles equipped with active suspension, turn the
suspension control switch OFF if it is necessary to jack up
the vehicle with the engine running.
2. TRANSMISSION PAN FILL
(a) Remove the refill plug and overflow plug.
(b) Fill the transmission through the refill hole until fluid be-
gins to trickle out of the overflow tube.
(c) Reinstall the overflow plug.
Page 128 of 3115
D12656
(a)(b)
(a)
(a)
(b)(b)
D12657
D12658
D12659
(c)(b)
D12660
- AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT
AT-31
1885 Author: Date:
2004 LAND CRUISER (RM1071U)
10. SEPARATE WIRE HARNESS
(a) Disconnect 3 connectors.
(b) Remove the 3 clamps from the transmission unit and sep-
arate the transmission wire.
11. REMOVE TORQUE CONVERTER CLUTCH MOUNT-
ING BOLT
(a) Remove the bolt and the hole plug.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)
(b) Turn the crankshaft to gain access to each bolt.
(c) Hold the crankshaft pulley nut with a wrench, and remove
the 6 bolts.
Torque: 48 N´m (490 kgf´cm, 35 ft´lbf)
HINT:
At the time of installation, first install the green colored bolt. And
then install the other 5 bolts.
12. DISCONNECT OIL COOLER PIPES
(a) Loosen the 2 union nuts.
(b) Remove the bolt and the clamp.
Torque: 12 N´m (122 kgf´cm, 9 ft´lbf)
(c) Remove the 2 union nuts and disconnect the 2 oil cooler
pipes.
Torque: 34 N´m (347 kgf´cm, 25 ft´lbf)
13. SEPARATE GROUND CABLE
Remove the bolt and separate the ground cable.
Torque: 20 N´m (204 kgf´cm, 15 ft´lbf)
14. REMOVE CROSSMEMBER AND TRANSTER CASE
PROTECTOR
(a) Support the transmission with a jack.
Page 191 of 3115
6RadioPOOR RECEPTION
Is the condition bad in comparison with other vehicles?
Are there any additional installation parts?
(Sun shade film, telephone antenna, etc.)
Check if there is any scratch and breaking of a wire on
the glass antenna and the defogger pattern.
(visual check. tester)
(See page BE-124
)
Is the contact of the plug jack of the radio OK?
Does the condition get better by using the outer
antenna (such as pillar antenna)?
Is the contact of the antenna terminal on the glass
surface and the defogger terminal?
Is the continuity of the antenna cord OK?
Check the grounding of the antenna, antenna cord.
Does the condition get better by replacing the
antenna cord?Take a measure for contact. An electric wave environment is bad.
Does the condition get better if
removing them?
Influence of additional installation parts.
Repair. (See page BE-75)
Check the radio.
Take a measure for contact.
Grounding failure. Replace the antenna cord.
Replace the antenna cord. Ye s
No
Radio assembly faultyYe s
Ye s
Ye s
Ye s
Ye s
Ye s
Ye s No
No
NoNo
No
No
No
NG
OK
Ye s
- BODY ELECTRICALAUDIO SYSTEM
BE-155
2528 Author: Date:
2004 LAND CRUISER (RM1071U)
Page 432 of 3115
BO1LD-03
H18905
Rear Door Opening TrimRoof Headlining Rear Trim
Upper Roof Side
Inner Garnish
Quarter Trim Jack CoverStriker Plate
Quarter Trim Panel Rear Door Scuff PlateQuarter Belt MouldingRear Mat
Rear Mat Set Plate Quarter Window
GlassStriker Plate Quarter Window
Glass Weatherstrip
Striker Plate
x5 Rear
Assist Grip Rear Vent Window Motor
Assist Grip
Plug
Assist Grip
Plug
- BODYQUARTER WINDOW GLASS
BO-61
2635 Author: Date:
2004 LAND CRUISER (RM1071U)
QUARTER WINDOW GLASS
COMPONENTS
Page 434 of 3115
BO4IW-01
H05257
: 5 Clips
H05258
H05259
H07941
11 Clips BO-62
- BODYQUARTER WINDOW GLASS
2636 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ROOF HEADLINING REAR TRIM
Using a screwdriver, remove the roof headlining rear trim.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE REAR NO. 2 SEATS
3. REMOVE REAR MAT SET PLATE
(a) Remove the 5 screws.
(b) Using a screwdriver, remove the rear mat set plate.
HINT:
Tape up the screwdriver tip before use.
4. REMOVE STRIKER PLATE
(a) Remove the 6 screws.
(b) Using a screwdriver, remove the striker plates.
HINT:
Tape up the screwdriver tip before use.
5. REMOVE REAR MAT
6. REMOVE REAR NO. 2 SEAT OUTER BELT FLOOR AN-
CHOR
Torque:42 N´m (430 kgf´cm, 31 ft´lbf)
7. REMOVE REAR NO. 1 SEAT OUTER BELT FLOOR AN-
CHOR
Torque:42 N´m (430 kgf´cm, 31 ft´lbf)
8. REMOVE REAR DOOR SCUFF PLATE
9. REMOVE REAR DOOR OPENING TRIM
10. REMOVE QUARTER TRIM PANEL
(a) Remove the quarter trim jack cover.
(b) Using a clip remover, remove the 2 clips.
(c) Remove the quarter trim panel, then disconnect the con-
nector.
11. REMOVE REAR NO. 2 SEAT OUTER BELT SHOUL-
DER ANCHOR
12. REMOVE REAR NO. 1 SEAT OUTER BELT SHOUL-
DER ANCHOR
Page 465 of 3115
BO1KP-04
H18921
Dome Light
Lens
Roof Headlining
Rear Trim
Roof Headlining Double Visor
Map Lamp
Center Pillar Garnish
Rear Mat
Set Plate
Striker Plate
Upper Roof
Side Inner Garnish Assist Grip
Cowl Side Trim Front Door Scuff Plate
Center Pillar Lower
Garnish CoverRear Door
Scuff PlateQuarter Trim PanelQuarter Trim
Jack Cover
Front Pillar Garnish Front Door
Opening TrimRear Door
Opening Trim Sun Visor
Holder
Assist Grip
Plug
Overhead
Console Box
Striker Plate
Center Pillar
Lower Garnish
Front Assist Grip
Front Assist Grip
Center Assist Gripw/ Curtain Shield Airbag:
42 (430, 31)
Adjustable
AnchorRear A/C Register
Rear A/C Register
Rear A/C Control Panel Rear A/C Register
Striker Plate
Striker Plate
Center Assist Grip
Center Assist Grip
Assist Grip
Rear
Assist Grip
x5Striker Plate
Center Assist Grip w/ Curtain Shield Airbag:
Adjustable
Anchor
Center Pillar Garnish
Center
Pillar
Garnish
: Specified torqueN´m (kgf´cm, ft´lbf)Rear Mat42 (430, 31)
Cap
Cap
Holder
rear
Assist Grip
w/ Curtain Shield Airbag:
Assist Grip
Assist Grip
Assist Grip Plug
w/ Curtain Shield Airbag:
Assist
Grip
Assist Grip Plug
Assist Grip
42 (430, 31)
Lens
Room Temperature
Sensor
BO-96
- BODYROOF HEADLINING
2670 Author: Date:
2004 LAND CRUISER (RM1071U)
ROOF HEADLINING
COMPONENTS
Page 467 of 3115
BO4IZ-01
H05257
: 5 Clips
H05258
H05259
H07941
11 Clips
- BODYROOF HEADLINING
BO-97
2671 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ROOF HEADLINING REAR TRIM
Using a screwdriver, remove the roof headlining rear trim.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE REAR NO. 2 SEATS
3. REMOVE REAR MAT SET PLATE
(a) Remove the 5 screws.
(b) Using a screwdriver, remove the rear mat set plate.
HINT:
Tape up the screwdriver tip before use.
4. REMOVE STRIKER PLATES
(a) Remove the 6 screws.
(b) Using a screwdriver, remove the striker plates.
HINT:
Tape up the screwdriver tip before use.
5. REMOVE REAR MAT
6. REMOVE REAR NO. 2 SEAT OUTER BELT FLOOR AN-
CHOR
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
7. REMOVE REAR NO. 1 SEAT OUTER BELT FLOOR AN-
CHOR
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
8. REMOVE REAR DOOR SCUFF PLATES
9. REMOVE REAR DOOR OPENING TRIMS
10. REMOVE QUARTER TRIM PANEL LH
(a) Remove the quarter trim jack cover.
(b) Using a clip remover, remove the 2 clips.
(c) Remove the quarter trim panel LH, then disconnect the
connector.
Page 552 of 3115
- BRAKEHYDRAULIC BRAKE BOOSTER
BR-43
2179 Author: Date:
2004 LAND CRUISER (RM1071U)
(5) When the solenoids are OFF, check that the brake
pedal can be depressed.
If the pedal cannot be depressed, replace the hydraulic brake
booster.
(6) Once, release the brake pedal. After depressing
and holding the brake pedal with stable force, turn
the SFLH and SFLR solenoids ON simultaneously.
HINT:
To protect the solenoids, TOYOTA hand-held tester turns OFF
automatically for 2 sec. after every solenoid has been turned
ON.
(7) Once release the brake pedal when the solenoids
are OFF, check that the brake pedal can be de-
pressed.
If the pedal cannot be depressed, replace the hydraulic brake
booster.
(g) Jack up and support the vehicle.
(h) Release the parking brake lever.
(i) Inspect the rear ABS solenoid.
(1) Select the ºSRHº on the TOYOTA hand-held tester.
(2) Turn the ºSRHº ON with the TOYOTA hand-held
tester and depress the brake pedal with stable
force, and rotate the right rear wheel by hand and
check it.
HINT:
To protect the solenoids, TOYOTA hand-held tester turns
OFF automatically for 2 sec. after every solenoid has
been turned ON.
When rotating the wheel fast, the fail-safe function is acti-
vated and judgement cannot be made properly. So rotate
the wheel as slowly as possible.
When solenoid is OFF, the wheel might stop temporarily.
However if the wheel rotates again, the function works
normally.
If the rear wheels stop, replace the hydraulic brake booster.
(3) Once, release the brake pedal and turn the ºSRHº
OFF, after depressing the brake pedal with stable
force and stop the rear right wheel by hand and
check it.
If the rear wheel rotate, replace the hydraulic brake booster.
(4) Depress the pedal with stable force, then turn the
ºSRHº and ºSRRº ON simultaneously.
(5) When the solenoids are ON, rotate the rear wheel
by hand and check it.
HINT:
To protect the solenoids, TOYOTA hand-held tester turns
OFF automatically for 2 sec. after every solenoid has
been turned ON.
Page 555 of 3115
BR-46
- BRAKEHYDRAULIC BRAKE BOOSTER
2182 Author: Date:
2004 LAND CRUISER (RM1071U)
(7) When the solenoids are OFF, check that the brake
pedal can be depressed.
If the pedal cannot be depressed, replace the hydraulic brake
booster.
(h) Jack up and support the vehicle.
(i) Release the parking brake lever.
(j) Shift the transfer shift lever to ºNº position and check that
the rear wheels by rotating them by hand.
(k) Inspect the rear TRAC & VSC solenoid operation.
(1) Select the ºSA3º and ºSTRº on the TOYOTA hand-
held tester.
(2) Turn the ºSA3º and ºSTRº ON simultaneously with
the TOYOTA hand-held tester, and check that the
rear wheel does not rotate by hand.
HINT:
When rotating the wheel fast, the fail-safe function is activated
and judgement cannot be made properly. So rotate the wheel
as slowly as possible.
If the rear wheels rotate, replace the hydraulic brake booster.
(3) Turn the ºSA3º and ºSTRº OFF simultaneously, and
check that the rear wheels by rotating them by
hand.
HINT:
To protect the solenoids, TOYOTA hand-held tester turns
OFF automatically 2 sec. after every solenoid has been
turned ON.
When rotating the wheel fast, the fail-safe function is acti-
vated and judgement cannot be made properly. So rotate
the wheel as slowly as possible.
NOTICE:
When operating it continuously, set the interval of more
than 20 sec.
If the rear wheels stop, replace the hydraulic brake booster.
(l) Inspect the right rear ABS solenoid.
(1) Select the ºSA3º, ºSTRº and ºSRRHº, on the TOYO-
TA hand-held tester.
(2) Turn the ºSA3º, ºSTRº and ºSRRHº ON simulta-
neously with the TOYOTA hand-held tester, and
check that the right rear wheel by rotating it by hand.
HINT:
To protect the solenoids, TOYOTA hand-held tester turns
OFF automatically 2 sec. after every solenoid has been
turned ON.
When rotating the wheel fast, the fail-safe function is acti-
vated and judgement cannot be made properly. So rotate
the wheel as slowly as possible.
When solenoid is OFF, the wheel might stop temporarily.
However if the wheel rotates again, the function works
normally.
If the rear wheels stop, replace the hydraulic brake booster.
Page 560 of 3115
F02829
F02831
- BRAKEHYDRAULIC BRAKE BOOSTER
BR-51
2187 Author: Date:
2004 LAND CRUISER (RM1071U)
(6) Depress and hold the brake pedal with stable force,
push and hold in MAIN push switch.
NOTICE:
Do not keep the MAIN push switch pushed down for more
than 10 sec. When operating it continuously, set the inter-
val of more than 20 sec.
(7) Check that the brake pedal cannot be depressed.
If the pedal can be depressed, replace the hydraulic brake
booster.
(8) Release the MAIN push switch, and check that the
brake pedal can be depressed.
If the pedal cannot be depressed, replace the hydraulic brake
booster.
(9) Release the brake pedal.
(k) Turn the ignition switch OFF, then reconnect the connec-
tor of sub- wire harness from the one with label of
ºFRONTº to ºREARº.
(l) Place ºSHEET Gº of ºREARº on the actuator checker.
(m) Jack up and support the vehicle.
(n) Start the engine and run it at idle.
(o) Inspect the rear solenoid operation.
(1) Turn the selector switch to ºRHº position.
(2) Depress the brake pedal several times and release
the pedal when the pump begins rotating. Wait until
the pump stops.
(3) Turn the ignition switch OFF.
(4) Depress the brake pedal with a force of 343 N (35
kgf, 77 lbf), record the fluid surface in the reservoir
tank of the hydraulic brake booster.
(5) Press the MAIN push switch for 10 sec., and check
that the fluid surface in the reservoir tank of the hy-
draulic brake booster dose not rise up at this time.
If the fluid surface level rises up, replace the hydraulic brake
booster.
NOTICE:
Do not press MAIN push switch for more than 10 sec. When
operating the switch continuously, do it an interval of more
than 20 sec.
(6) Release the brake pedal and check that brake ped-
al is not hard to depress.
If pedal is hard to depress, replace the hydraulic brake booster.
(7) Start the engine and run it at idle.
(8) Depress the brake pedal.
(9) Release the parking brake lever and shift the shift
lever to ºLº position.
(10) Once, release the brake pedal. After depressing the
brake pedal with stable force, then push and hold
MAIN push switch.