brake pads TOYOTA LAND CRUISER 1998 Factory Repair Manual

BR0TA-04
F04974
F04975
- BRAKEFRONT BRAKE CALIPER
BR-19
2155 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. DISCONNECT BRAKE LINE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)
(b) Use a container to catch the brake fluid as it drains out.
3. REMOVE CALIPER
Remove the 2 mounting bolts and remove the caliper.
Torque: 123 N´m (1,250 kgf´cm, 90 ft´lbf)
4. REMOVE CLIP AND 2 PINS
5. REMOVE 2 PAD RETAINER CLIPS
6. REMOVE 2 PADS, ANTI-SQUEAL SHIMS AND PAD
RETAINERS

BR0JI-1 1
F04993
F04994
F04995
BR-16
- BRAKEFRONT BRAKE PAD
2152 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
1. REMOVE FRONT WHEEL
2. INSPECT PAD LINING THICKNESS
Check the pad thickness through the caliper inspection hole
and replace the pads if they are not within the specification.
Minimum thickness: 1.0 mm (0.039 in.)
3. REMOVE CLIP AND 2 PINS
4. REMOVE 2 PAD RETAINER CLIPS
5. REMOVE 2 PADS, ANTI-SQUEAL SHIMS AND PAD
RETAINERS
NOTICE:
The pad retainer clip and clip can be used again provided
that they have sufficient rebound, no deformation, cracks
or wear, and have had all rust, dirt and foreign particles
cleaned off.
6. CHECK DISC THICKNESS AND DISC RUNOUT
(See page BR-21)
7. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti-squeal shims must be
replaced together with the pad.
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in the piston with a hammer handle or an equiva-
lent.
HINT:

Always change the pads on one wheel at a time as there
is a possibility of opposite piston fling out.

If the piston is difficult to push in, loosen the bleeder plug
and push in the piston while letting some brake fluid es-
cape.
(c) Install the 2 pad retainers to each caliper piston.
(d) Install the anti-squeal shim to each pad.
HINT:
Apply disc brake grease to both sides of the anti-squeal shims
(See page BR-15).
(e) Install the 2 pads.
HINT:
Apply disc brake grease to the pads indicated by the arrows
(See page BR-15).

- BRAKEFRONT BRAKE PAD
BR-17
2153 Author
: Date
:
2004 LAND CRUISER (RM1071U)
NOTICE:
There should be no oil or grease adhering to the friction
surfaces of the pads or the disc.
8. INSTALL 2 PAD RETAINER CLIPS AND 2 PINS
9. INSTALL CLIP
10. INSTALL FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
11. DEPRESS BRAKE PEDAL SEVERAL TIMES
12. CHECK THAT FLUID LEVEL IS AT MAX LINE

BR0JS-03
F04992
BR-28
- BRAKEREAR BRAKE CALIPER
2164 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DISCONNECT FLEXIBLE HOSE
Remove the union bolt and gasket from the caliper, then discon-
nect the flexible hose from the caliper. Use a container to catch
brake fluid as it drains out.
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Install the flexible hose lock securely in the lock hole in the cali-
per.
2. REMOVE CALIPER
(a) Hold the sliding pin and loosen the 2 installation bolts.
Torque: 26 N´m (270 kgf´cm, 20 ft´lbf)
(b) Remove the 2 installation bolts.
(c) Remove the caliper from the torque plate.
3. REMOVE 2 BRAKE PADS WITH ANTI- SQUEAL
SHIMS
4. REMOVE 4 PAD SUPPORT PLATES

BR0JS-03
F04992
BR-28
- BRAKEREAR BRAKE CALIPER
2164 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DISCONNECT FLEXIBLE HOSE
Remove the union bolt and gasket from the caliper, then discon-
nect the flexible hose from the caliper. Use a container to catch
brake fluid as it drains out.
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Install the flexible hose lock securely in the lock hole in the cali-
per.
2. REMOVE CALIPER
(a) Hold the sliding pin and loosen the 2 installation bolts.
Torque: 26 N´m (270 kgf´cm, 20 ft´lbf)
(b) Remove the 2 installation bolts.
(c) Remove the caliper from the torque plate.
3. REMOVE 2 BRAKE PADS WITH ANTI- SQUEAL
SHIMS
4. REMOVE 4 PAD SUPPORT PLATES

F04989
BR0TB-04
F04990
F04991
- BRAKEREAR BRAKE PAD
BR-25
2161 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
1. REMOVE REAR WHEEL
2. INSPECT PAD LINING THICKNESS
Check the pad thickness through the caliper inspection hole
and replace pads if not within the specification.
Minimum thickness: 1.0 mm (0.039 in.)
3. REMOVE BRAKE CALIPER
(a) Remove the 2 mounting bolts.
(b) Remove the caliper and suspend it so the hose is not
stretched.
HINT:
Do not disconnect the flexible hose.
4. REMOVE 2 PADS AND 4 ANTI-SQUEAL SHIMS
5. REMOVE 4 PAD SUPPORT PLATES
NOTICE:
The pad support plates can be used again provided that
they have sufficient rebound, no deformation, cracks or
wear, and have had all rust, dirt and foreign particles
cleaned off.
6. CHECK DISC THICKNESS AND RUNOUT
(See page BR-30)
7. INSTALL PAD SUPPORT PLATES
8. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti-squeal shims must be
replaced together with the pads.
Install the 4 anti-squeal shims to the pads.
HINT:
Apply disc brake grease to both sides of the inner anti-squeal
shims (See page BR-24).
NOTICE:
Do not allow oil or grease to get on the rubbing face.
9. INSTALL CALIPER
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in the pistons with a hammer handle or an equiva-
lent.
HINT:

Always change the pads on one wheel at a time as there
is a possibility of the opposite piston flying out.

If the piston is difficult to push in, loosen the bleeder plug
and push in the piston while letting some fluid escape.

MA0055
MA02T-02
- MAINTENANCEBRAKE
MA-7
55 Author
: Date
:
2004 LAND CRUISER (RM1071U)
BRAKE
INSPECTION
1. INSPECT BRAKE LINE PIPES AND HOSES
HINT:
Check in a well lighted area. Check the entire circumference
and length of the brake hoses using a mirror as required. Turn
the front wheels fully right or left before checking the front brake.
(a) Check the all brake lines and hoses for damage.
(b) Check the all brake lines and hoses for wear.
(c) Check the all brake lines and hoses for deformation.
(d) Check the all brake lines and hoses for cracks.
(e) Check the all brake lines and hoses for corrosion.
(f) Check the all brake lines and hoses for leaks.
(g) Check the all brake lines and hoses for bends.
(h) Check the all brake lines and hoses for twists.
(i) Check all clamps for tightness and connections for leak-
age.
(j) Check that the hoses and lines are clear of sharp edges,
moving parts and the exhaust system.
(k) Check that the lines installed in grommets pass through
the center of the grommets.
2. INSPECT FRONT AND REAR BRAKE PADS AND
DISCS
(FRONT PADS: See page BR-16)
(REAR PADS: See page BR-25)
(FRONT DISCS: See page BR-21)
(REAR DISCS: See page BR-30)
3. INSPECT PARKING BRAKE LININGS AND DRUMS
(See page BR-36)