roof TOYOTA LAND CRUISER 1998 Factory Repair Manual

N13790
Low Pressure
Service Valve
High Pressure
Service Valve
I08298
Properly
Charged
Insufficiently
Charged
AC-12
- AIR CONDITIONINGAIR CONDITIONING SYSTEM
2737 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3. CHARGE REFRIGERANT INTO REFRIGERATION
SYSTEM
If there is no leak after refrigerant leak check, charge the proper
amount of refrigerant into the refrigeration system.
CAUTION:

Do not run the engine when charging the system
through the high pressure side.

Do not open the low pressure hand valve when the
system is being charged with liquid refrigerant.
(a) Open the high pressure hand valve fully.
(b) Charge specified amount of refrigerant, then close the
high pressure hand valve.
HINT:
No bubbles in the sight glass indicates that the system is fully
charged.
(c) Partially charge the refrigeration system with refrigerant.
(1) Start engine and race engine at 1,500 rpm.
(2) Set fan speed selector to ºHIº.
(3) Set temperature control to ºMAX. COOLº.
(4) Set air inlet control to ºRECIRCº.
(5) Fully open doors (Sliding roof: closed).
(6) Open the low pressure hand valve.
CAUTION:
Do not open the high pressure hand valve.
(d) Charge refrigerant until bubbles disappear and check the
pressure on the gauge through the sight glass.

AC1KB-05
I25893
Roof Side Inner Upper Garnish Roof Headlining Rear Trim
No.1 Cooler Air Duct
Quarter Trim Panel RH
Rear Floor Mat Support Plate
O-Ring
Liquid Tube
Suction Tube Rear Door Scuff Plate
43 (430, 32)
10 (100, 7)
43 (430, 32)
N´m (kgf´cm, ft´lbf) : Specified torque

Non-reusable part
Rear Cooling Unit
43 (430, 32)
Adjusting
Anchor
43 (430, 32)
AC-30
- AIR CONDITIONINGREAR COOLING UNIT
2755 Author
: Date
:
2004 LAND CRUISER (RM1071U)
COMPONENTS

AC1KC-05
I06687
I15822
I15823
AC-32
- AIR CONDITIONINGREAR COOLING UNIT
2757 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
HINT:
At the time of installation, first evacuate air from refrigeration
system.
Then, charge the system with the refrigerant and inspect for
leaks of the refrigerant.
Specified amount: 1,050 ± 50 g (37.04 ± 1.76 oz.)
2. DISCONNECT LIQUID AND SUCTION TUBES
Remove the bolt and slide the plate, then disconnect both
tubes.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of installation, lubricate 2 new O-rings with com-
pressor oil and install them to the tubes.
3. REMOVE REAR DOOR SCUFF PLATE RH
4. REMOVE REAR FLOOR MAT SUPPORT PLATE
5. REMOVE ROOF HEADLINING REAR TRIM
6. REMOVE QUARTER TRIM PANEL RH
7. REMOVE ROOF SIDE INNER UPPER GARNISH
(See page BO-97)
8. REMOVE NO. 1 COOLER AIR DUCT
(a) Remove the 3 roof headlining set clips.
(b) Remove the 5 clips and the No. 1 cooler air duct.

I06748
AC1LO-05
AC-88
- AIR CONDITIONINGROOM TEMPERATURE SENSOR (for Rear A/C)
2813 Author
: Date
:
2004 LAND CRUISER (RM1071U)
ROOM TEMPERATURE SENSOR
(for Rear A/C)
INSPECTION
1. REMOVE ROOM TEMPERATURE SENSOR
Using a scrwedriver, pull out the room temperature sensor, then
disconnect the connector.
HINT:
Tape the screwdriver tip before use.
2. INSPECT ROOM TEMPERATURE SENSOR
(See page DI-1330)
3. INSTALL ROOM TEMPERATURE SENSOR
(a) Connect the connector.
(b) Insert the room temperature sensor to the roof headlining.

BE1Z9-01
Mode Select Switch
On Duration
Normal Mode
Pressed for 3 sec.
6. Compass Non-display Mode
Pressed for 6 sec.
7. Zone Setting ModeIgnition switch ON.
Pressed for 9 sec.
Zone area +1 Mode Select Switch ON
8. Calibration Mode
Leaving it untouched
for a while
Normal Mode
- BODY ELECTRICALCOMPASS
BE-71
2444 Author
: Date
:
2004 LAND CRUISER (RM1071U)
COMPASS
PRE-CHECK
1. SELECTING COMPASS DISPLAY MODE
The mode select switch allows you to select a Display or Non-display mode of the compass.
The mode select is operated by the automatic glare-proof / non-glare proof switch on the inner mirror.
2. SETTING ZONE
Deviation between the magnetic north and ºactual northº differs depending on the terrestrial location, there-
fore, an adjustment in magnetism is required. Since the magnetic condition differs according to the area
where the vehicle will be used, it is necessary for each user to set the zone. (Refer to ºCompass Zone Mapº).
The zone setting can be changed using the mode select switch of the inner mirror.
3. PERFORMING CALIBRATION
Because each vehicle has its own magnetic field, calibration should be performed for each vehicle. This com-
pass function is used when storing the record of the vehicle's magnetic field.
4. WHEN COMPASS MAGNETIZED:
A compass could be magnetized during shipping by vessels or freight cars. Before delivery, therefore, make
sure to perform calibration and ensure that calibration can be done. If it cannot be done (cannot complete
in spite of driving round several times), it may be caused by magnetization. Demagnetize the vehicle using
a demagnetizer and perform calibration again.
5. SETTING COMPASS

I18957
ZONE SETTING NUMBER BE-72
- BODY ELECTRICALCOMPASS
2445 Author
: Date
:
2004 LAND CRUISER (RM1071U)
6. SELECTING DISPLAY MODE
(a) Turn the ignition switch ON.
(b) Check that the LED on the inner mirror is lit (green).
(c) Check that the compass display indicates an azimuthal direction (N, NE, E, SE, S, SW, W, or NW) or
ºCº.
(d) Pressing the mode select switch on the inner mirror for 3 sec. or more erases the above mentioned
display and activates the Non-display mode.
HINT:

Immediately after pressing the mode select switch, the LED goes off activating the Non-glare-proof
mode. However, when the switch remains pressed, the LED is lit again after 3 sec. and the system
enters the automatic glare-proof mode.

Keep pressing the mode select switch for 3 sec. after selection of the compass display mode will acti-
vate the zone setting mode, showing a number (1-15) on the compass display.
7. ZONE SETTING MODE

BE2E4-01
I25538
Cowl Side J/B RH

SECURITY Fuse
Overhead Junction Block

Sliding Roof Switch

Garage Door Opener Switch
- BODY ELECTRICALOVERHEAD JUNCTION BLOCK
BE-181
2554 Author
: Date
:
2004 LAND CRUISER (RM1071U)
OVERHEAD JUNCTION BLOCK
LOCATION

BE-24
- BODY ELECTRICALPOWER SOURCE
2397 Author
: Date
:
2004 LAND CRUISER (RM1071U) ACC 13 - Ground
Ignition switch ACCBattery positive voltage
CIG 15 - GroundIgnition switch ACCBattery positive voltage
PWR OUTLET 17 - GroundIgnition switch ACCBattery positive voltage
OBD-2 20 - GroundConstantBattery positive voltage
STOP 22 - GroundConstantBattery positive voltage
A/C 24 - GroundIgnition switch ONBattery positive voltage
BATT CHARGE 26 - GroundConstantBattery positive voltage
DBL LOCK 39 - GroundConstantBattery positive voltage
ECU-B1 29 - GroundConstantBattery positive voltage
ECU-IG1 32 - GroundIgnition switch ONBattery positive voltage
GAUGE1 34 - GroundIgnition switch ONBattery positive voltage
EFI or ECD NO.2 35 - GroundConstantBattery positive voltage
RR WIPER 37 - GroundIgnition switch ONBattery positive voltage
SUN ROOF 39 - GroundConstantBattery positive voltage
DOOR 41 - GroundConstantBattery positive voltage
LH SEAT 43 - GroundConstantBattery positive voltage
IDLE UP 46 - GroundRear deffoger system ONBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
(b) Remove the relay from the junction block and inspect the
connector on junction block side.
Relay Tester connectionConditionSpecified condition
DOME 1 - GroundConstantBattery positive voltage
DOME 5 - GroundConstantBattery positive voltage
ACC 5 - GroundConstantBattery positive voltage
ACC 2 - GroundIgnition switch ONBattery positive voltage
IG1 NO.2 5 - GroundConstantBattery positive voltage
IG1 NO.2 2 - GroundIgnition switch ONBattery positive voltage
DEFOG 5 - GroundConstantBattery positive voltage
DEFOG 1 - GroundIgnition switch ONBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.

I24922
Cowl Side J/B LH
ABCD
Relays:
A. DEFOG
B. IG1 No.2
C. ACC
D. DOME Fuses:
1. AHC-IG
2. POWER HTR
3. FUEL HTR
4. AHC-B
5. DEFOG
6. AM1
7. ACC
8. CIG
9. PWR OUTLET
10. OBD-2
11. STOP
12. A/C
13. BATT CHARGE
14. DBL LOCK
15. ECU-B1
16. ECU-IG1
17. GAUGE1
18. EFI or ECD NO.2
19. RR WIPER
20. SUN ROOF
21. DOOR
22. LH SEAT
23. IDLE UP
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
19 20 21 22 23
- BODY ELECTRICALPOWER SOURCE
BE-13
2386 Author
: Date
:
2004 LAND CRUISER (RM1071U)

BE0S9-04
I06151
I04045
Wire Harness Side:
- BODY ELECTRICALSLIDING ROOF SYSTEM
BE-107
2480 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. INSPECT SLIDING ROOF SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
SLIDE OPEN3 - 5Continuity
SLIDE OFF -No continuity
SLIDE CLOSE3 - 4Continuity
TILT DOWN2 - 3Continuity
TILT OFF -No continuity
TILT UP1 - 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT SLIDING ROOF CONTROL ASSEMBLY CIR-
CUIT
Disconnect the connector from the ECU and inspect the con-
nector on the wire harness side, as shown in the chart.
Tester connectionConditionSpecified condition
1 - GroundConstantContinuity
4 - GroundSliding roof control switch (TILT) OFF or CLOSENo continuity
4 - GroundSliding roof control switch (TILT) UPContinuity
5 - GroundConstantBattery positive voltage
3 - GroundConstantContinuity
3 - GroundSliding roof control switch (TILT) OFF or UPNo continuity
7 - GroundSliding roof control switch (TILT) DOWNContinuity
8 - GroundIgnition switch LOCK or ACC* No voltage
8 - GroundIgnition switch ONBattery positive voltage
9 - GroundSliding roof control switch (SLIDE) OFF or
CLOSENo continuity
9 - GroundSliding roof control switch (SLIDE) OPENContinuity
10 - GroundSliding roof control switch (SLIDE) OFF or OPENNo continuity
10 - GroundSliding roof control switch (SLIDE) CLOSEContinuity
*: Exceptions: During 45 second period after ignition switch
ON"OFF (ACC) or until driver or passenger door is opened af-
ter ignition switch ON"OFF (ACC).