wheel torque TOYOTA LAND CRUISER 2004 J100 Owners Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2004, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 2004 J100Pages: 342, PDF Size: 6.04 MB
Page 273 of 342
265
2004 L/C100 from Aug ’03 Prod. (OM60A04U)
CAUTION
Never use oil or grease on the
bolts or nuts. Doing so may
lead to overtightening the nuts
and damaging the bolts. The
nuts may loosen and the
wheels may fall off, which
could cause a serious acci-
dent. If there is oil or grease
on any bolt or nut, clean it.
—Lowering your vehicle
9. Lower the vehicle completely
and tighten the wheel nuts.
Turn the jack handle extension coun-
terclockwise with handle to lower the
vehicle, making sure the handle re-
mains firmly fitted onto the jack han-
dle extension.
Use only the wheel nut wrench and
turn it clockwise to tighten the nuts.
Do not use other tools or any addition-
al leverage other than your hands,
such as a hammer, pipe or your foot.
Make sure the wrench is securely en-
gaged over the nut. Tighten each nut a little at a time in
the order shown. Repeat the process
until all the nuts are tight.
CAUTION
When lowering the vehicle,
make sure all portions of your
body and all other persons
around will not be injured as
the vehicle is lowered to the
ground.
Have the wheel nuts tightened
with a torque wrench to 131
N·m (13.4 kgf·m, 96.6 ft·lbf), as
soon as possible after chang-
ing wheels. Otherwise, the
nuts may loosen and the
wheels may fall off, which
could cause a serious acci-
dent.
Page 274 of 342
266
2004 L/C100 from Aug ’03 Prod. (OM60A04U)
—Reinstalling wheel ornament
10. Reinstall the wheel ornament.Put the wheel ornament into position.
And press hand firmly on one side of
wheel ornament and then firmly tap
the other side around the edge of
wheel ornament with the heel of your
hand to snap into place.
CAUTION
Take due care in handling the or-
nament to avoid unexpected per-
sonal injury.
—After changing wheels
11. Check the air pressure of the re- placed tire.
Adjust the air pressu re to the specifi-
cation designated on page 326. If the
pressure is lower, dr ive slowly to the
nearest service station and fill to the
correct pressure.
Do not forget to reinstall the tire infla-
tion valve cap as dirt and moisture
could get into th e valve core and
possibly cause air leakage. If the cap
is missing, have a new one put on as
soon as possible.
12. Restow all the tools, jack and flat tire securely.
As soon after changing wheels as
possible, tighten the wheel nuts to the
torque specified on page 326 with a
torque wrench. Have a technician re-
pair the flat tire.
This is the same procedure for chang-
ing or rotating your tires.CAUTION
Before driving, make sure all the
tools, jack and flat tire are se-
curely in place in their storage
location to reduce the possibility
of personal injury during a colli-
sion or sudden braking.
Page 334 of 342
326
2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Tires
Tire size and inflation pressure:kPa (psi)
Ti r e siz e
FrontRearWheel sizeNormal drivingTr ailer towingNormal drivingTr ailer towing
P275/65R17 113S200 (29)220 (32)220 (32)240 (35)17 8JJ
P275/60R18 111H200 (29)220 (32)220 (32)240 (35)18 8JJ
Wheel nut torque, N·m (kgf·m, ft·lbf): 131 (13.4, 96.6)
NOTE: For a complete information on tires (e.g. replacing tires or replacing wheels), see “Checking tire inflation pressure” on page 299 through “Aluminum wheel precautions” on page 307.