tires TOYOTA LAND CRUISER 2006 J100 Owners Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2006, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 2006 J100Pages: 364, PDF Size: 6.03 MB
Page 8 of 364
viii
Tires and loading on your Toyota
Underinflated or overinflated tire inflation pressure
and the excess load may result in the deterioration
of steering ability and braking ability, leading to
an accident. Check the tire inflation pressure peri-
odically and be sure to keep the load limits given
in this Owner ’s Manual. For details about tire infla-
tion pressure and load limits, see pages 320 and
246.
Scrapping of your Toyota
The SRS airbag and seat belt pretensioner devices in
your Toyota contain explosive chemicals. If the vehicle
is scrapped with the airbags and pretensioners left as
they are, this may cause an accident such as fire. Be
sure to have the systems of the SRS airbag and seat
belt pretensioner removed and disposed of by a qualified
service shop or by your Toyota dealer before you dis-
pose of your vehicle.
Page 68 of 364
58
The seat belt pretensioner system con-
sists mainly of the following components,
and their locations are shown in the il-
lustration.1. Front airbag sensors
2. SRS warning light
3. Seat belt pretensioner assemblies
4. Airbag sensor assembly
The seat belt pretensioners are controlled
by the airbag sensor assembly. The airbag
sensor assembly consists of a safing sen-
sor and airbag sensor. When the seat belt pretensioners are acti-
vated, an operating noise may be heard
and a small amount of non
−toxic gas may
be released. This does not indicate that
a fire is occurring. This gas is normally
harmless.
Once the seat belt pretensioners have
been activated, the seat belt retractors
remain locked.
CAUTION
Do not modify, remove, strike or
open the seat belt pretensioner as-
semblies, airbag sensor or sur-
rounding area or wiring. Failure to
follow these instructions may pre-
vent the seat belt pretensioners
from activating correctly, cause sud-
den operation of the system or dis-
able the system, which could result
in death or serious injury.
Do not use tires or wheels other
than the manufacturer ’s recom-
mended size. Such a use may cause
the curtain shield airbags and seat
belt pretensioners to inflate acci-
dentally, resulting in death or seri-
ous injury. For details, see “Check-
ing and replacing tires” on page
323.
Do not place luggage heavier than
specified on the roof luggage carri-
er. Such luggage may cause the
curtain shield airbags and seat belt
pretensioners to inflate accidentally,
resulting in death or serious injury.
For details, see “Roof luggage car-
rier” on page 218.
Do not modify or change the sus-
pension system. Such changes may
cause the curtain shield airbags to
inflate accidentally, resulting in
death or serious injury.
Failure to follow these instructions
can result in death or serious inju-
ries. Consult your Toyota dealer
about any repair and modification.
Page 80 of 364
70
The curtain shield airbags may not acti-
vate if the vehicle is subjected to a
collision from the side at certain
angles, or a collision to the side of the
vehicle body other than the passenger
compartment as shown in the illustra-
tion.
The curtain shield airbags are designed to
inflate when the passenger compartment
area suffers a severe impact from the
side or vehicle rollover.
Always wear your seat belts properly.
The angle of
vehicle tip−up
is marginal Skidding vehicle
hitting a curb
stone
The curtain shield airbags may inflate
if the angle of vehicle tip up is margin-
al or if the skidding vehicle’s tires hit
a curb stone laterally as shown in the
illustration.
Collision from
the front
Collision from
the rear
Pitch end over end
The curtain shield airbags are generally
not designed to inflate if the vehicle is
involved in a front or rear collision, if
it pitches end over end or if it is in-
volved in a low speed side collision.
Page 85 of 364
75
13c800b
Do not attach a microphone or any
other device or object around the
area where the curtain shield airbag
activates such as on the windshield
glass, side door glass, front, center
and roof side garnish, roof interior
or assist grips. When the curtain
shield airbag inflates, the micro-
phone or other device or object will
be thrown away with great force or
the curtain shield airbag may not
activate correctly, resulting in death
or serious injury.
Do not hook a hanger, heavy or
sharp pointed objects on the coat
hook. If the curtain shield airbags
inflate, those items will be thrown
away with great force or the curtain
shield airbags may not activate cor-
rectly, resulting in death or serious
injury. When you hang clothes,
hang them on the coat hook direct-
ly.
Do not use seat accessories which
cover the parts where the side air-
bags inflate. Such accessories may
prevent the side airbags from acti-
vating correctly, causing death or
serious injury.
Do not modify or replace the seats
or upholstery of the seats with side
airbags. Such changes may prevent
the side airbag system from activat-
ing correctly, disable the system or
cause the side airbags to inflate ac-
cidentally, resulting in death or seri-
ous injury.
Do not disassemble or repair the
front and rear pillars and roof side
rails containing the curtain shield
airbags. Such changes may disable
the system or cause the curtain
shield airbags to inflate accidental-
ly, resulting in death or serious in-
jury.
Do not modify or change the sus-
pension system. Such changes may
cause the curtain shield airbags to
inflate accidentally, resulting in
death or serious injury.
Do not use tires or wheels other
than the manufacturer ’s recom-
mended size. Such a use may cause
the curtain shield airbags to inflate
accidentally, resulting in death or
serious injury. For details, see
“Checking and replacing tires” on
page 323.
Page 155 of 364
145
The brake actuator temperature increases
during the active traction control system
or vehicle stability control system operat-
ing. If the brake actuator temperature be-
comes too high while the active traction
control system or vehicle stability control
system is operating, a buzzer will start to
sound intermittently to indicate that the
active traction control system can no lon-
ger operate. In this case, immediately stop
your vehicle at a safe place. If the system
continues to operate, the buzzer sound
changes from intermittent to continuous.
(The continuous buzzer sounds for about
3 seconds.) At the time, the “VSC/TRAC”
warning light will come on and the active
traction control system temporarily stops
operating in order to protect the brake
actuator. (Although the active traction con-
trol system does not operate, there is no
problem to continue your driving.) The
system will be automatically restored after
a short time and “VSC/TRAC” warning
light goes off if the accelerator pedal is
released.
When the “ABS” warning light come on,
the active traction control system is not
operating.
The “VSC/TRAC” warning light will come
on when the ignition key is turned “ON”,
and will go off after a few seconds.The “VSC/TRAC” warning light may stay
on for 60 seconds after the ignition key
is turned to “ON” position. It is normal if
it goes off after a few seconds.
Depressing the brake pedal repeatedly
may turn on the “VSC/TRAC” warning
light. It is normal if it goes off after a few
seconds.
When the “VSC/TRAC” warning light
comes on the active traction control sys-
tem is not operating, but there is no prob-
lem if you continue to drive.
In the following cases, contact your Toyota
dealer:
The “VSC/TRAC” warning light does not
come on after the ignition key is turned
“ON”.
The “VSC/TRAC” remains on after the
ignition key is turned “ON”.
CAUTION
Under certain slippery road condi-
tions, full traction of the vehicles and
power to 4 wheels may not be main-
tained, even though the active trac-
tion control system is in operation.
Do not drive the vehicle under any
speed or maneuvering conditions
which will cause the vehicle to lose
traction. In situations where the road
surface is covered with ice or snow,
your vehicle should be fitted with
snow tires or tire chains. Always
drive at an appropriate and cautious
speed for the road conditions pres-
ent.
Page 156 of 364
146
The vehicle stability control system
helps provide integrated control of the
systems such as anti lock brake, trac-
tion control, engine control, etc. This
system automatically controls the out-
put of the brakes or engine to help
prevent the vehicle from skidding under
adverse conditions.
The system activates when the vehicle
speed is about more than 15 km/h (9
mph).
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the ve-
hicle stability control system is in the
self−check mode and does not indicate a
malfunction.CAUTION
Active traction control system, ve-
hicle stability control system and
anti lock brake system are electron-
ic systems designed to help the
driver maintain control under ad-
verse conditions. They are not a
substitute for safe driving practices.
Factors including speed, road con-
ditions and driver steering input
can all affect whether active trac-
tion control system, vehicle stability
control system and anti lock brake
system will be effective in prevent-
ing a loss of control. Always keep
safety driving in mind. If the slip
indicator light flashes, sounding an
alarm, special care should be taken
while driving.
Only use tires of specified size. The
size, manufacturer, brand and tread
pattern for all 4 tires should be the
same. If you use the tires other
than specified, or different type or
size, the vehicle stability control
system may not function correctly.
When replacing the tires or wheels,
contact your Toyota dealer. (See
“Checking and replacing tires” on
page 323.)
Vehicle stability control
system
Page 158 of 364
148
When the “ABS” warning light comes on,
the vehicle stability control system is not
operating.
The “VSC/TRAC” warning light and “VSC
OFF” indicator light will come on when the
ignition key is turned “ON”, and will go off
after a few seconds.
The “VSC/TRAC” warning light and “VSC
OFF” indicator light may stay on for 60
seconds after the ignition key is turned to
“ON” position. It is normal if they go off
after a few seconds.
Depressing the brake pedal repeatedly
may turn on the lights. It is normal if they
go off after a few seconds.
When the “VSC/TRAC” warning light and
“VSC OFF” indicator light come on, the
vehicle stability control system is not op-
erating, but there is no problem if you
continue to drive.
In the following cases, contact your Toyota
dealer:
The “VSC/TRAC” warning light, “VSC
OFF” indicator light and slip indicator
light do not come on after the ignition
key is turned “ON”.
The “VSC/TRAC” warning light and
“VSC OFF” indicator light remain on af-
ter the ignition key is turned “ON”.
The “VSC OFF” indicator light comes
on while driving without pushing the
center differential lock switch.
16C521a
Low tire pressure warning light
The light warns you that the tire infla-
tion pressure is low.
The low tire pressure warning light comes
on when the ignition key is turned to the
“ON” position and goes off after a few
seconds. This means the low tire pres-
sure warning light is operating properly.
If the tire inflation pressure becomes low,
the light comes on again.If the low tire pressure warning light does
not go off or comes on during driving, it
indicates that tire inflation pressure is low.
Make sure there is no flat tire. If the
light comes on again even after tire infla-
tion pressure adjustment, you may have a
flat tire. If there is not adequate air
pressure in the tires, the light will not go
off.
The light may turn on due to natural
causes such as natural air leaks or tire
inflation pressure changes caused by tem-
perature. In this case, adjusting the tire
inflation pressure will turn off the light.
The tire pressure warning system is not
a substitute for checking tire inflation
pressure.
For details about adjusting the tire
inflation pressure, see “Checking tire
inflation pressure” on page 320.
If the low tire pressure warning light
comes on, the action you must take is
different depending on the type of tires
used.
Tire pressure warning system—
Page 159 of 364
149
Stop your vehicle at a safe place as soon
as possible and check that the tire infla-
tion pressure is as specified on the tire
and loading information label. If the low
tire pressure warning light comes on even
after tire inflation pressure adjustment, it
is probable that you have a flat tire. If
the tire goes flat, change to the spare
tire. (See page 275.)
The spare tire is not equipped with the
tire pressure sensor. So, the low tire
pressure warning light remains on even if
the spare tire is mounted.
The light goes off a few minutes after air
is put into the deflated tire.CAUTION
If the low tire pressure warning light
comes on, observe the following in-
structions:
Decelerate as soon as possible to
the most appropriate speed that
conditions permit.
Avoid abrupt steering wheel maneu-
vering and braking. If the vehicle
tires deteriorate, you could lose
control of the steering wheel or the
brakes, causing death or serious in-
jury.
The warning system may not acti-
vate immediately if bursts or sud-
den air leakage should occur.
Each tire, including the spare (if pro-
vided), should be checked monthly
when cold and inflated to the inflation
pressure recommended by the vehicle
manufacture on the vehicle placard or
tire inflation pressure label. (If your
vehicle has tires of a different size
than the size indicated on the vehicle
placard or tire inflation pressure la-
bel, you should consult the appropri-
ate section of the owner ’s manual to
determine the proper tire inflation
pressure.) When the low tire pressure
telltale is illuminated, one or more of
your tires is significantly under in-
flated. You should stop and check
your tires as soon as possible, and
inflate them to the proper pressure as
indicated on the vehicle’s tire infor-
mation placard. Driving on a signifi-
cantly under inflated tire causes the
tire to overheat and can lead to tire
failure. Under inflation also reduces
fuel efficiency and tire tread life, and
may affect the vehicle’s handling and
stopping ability.
Page 160 of 364
150
Your vehicle has also been equipped
with a TPMS malfunction telltale to
indicate when the system is not oper-
ating properly. When the malfunction
telltale is illuminated, the system may
not be able to detect or signal low
tire pressure as intended. TPMS mal-
function may occur for a variety of
reasons, including the installation of
incompatible replacement tires on the
vehicle. Always check the TPMS mal-
function telltale after replacing one or
more tires on your vehicle to ensure
that the replacement tires are compat-
ible with the TPMS.NOTICE
Do not use liquid sealants for a flat
tire as tire pressure sensors will be
damaged.
When the tires must be repaired or
replaced, have them repaired or re-
placed by the nearest Toyota dealer
or authorized tire dealer. The tire
pressure sensors will be affected
by the installation or removal of
tires.
The tire pressure warning system is
not to be used as a substitute for
regular inspections. Be sure to
check the air pressure in the tires
on a regular basis.
When the tires must be replaced,
replace the grommets for tire pres-
sure sensors as well.
Tire inflation pressure should be
adjusted for all 5 tires (including a
spare tire).
Warning tends to turn on when
driving at lower outside tempera-
ture, such as in winter, because tire
inflation pressure will be decreased
due to the low temperature. In this
case, after adjustment and initializa-
tion, leave the ignition on for about
20 minutes and increase the tire
inflation pressure by 20 to 30 kPa.
Page 161 of 364
151
SYSTEM MALFUNCTION
If the low tire pressure warning light
blinks, it indicates a system malfunc-
tion. Contact your Toyota dealer.
The system will be disabled in the condi-
tions below:
Electric devices or facilities using simi-
lar radio wave frequencies are nearby.
If a radio set at similar frequencies is
in use.
Much snowflakes or ice gets on the
vehicle, in particular, around the wheels
or wheel housings.
Non−genuine Toyota wheels are used.
Snow tires or tire chains are used.
The sensor battery is expired.
The tires not equipped with tire pres-
sure sensor are used.
Radio waves from the air pressure sen-
sor installed on the spare tire cannot
be received.
Although the tires are equipped with
tire pressure sensors, the selector
switch (see page 154) is set to other
tire setting.
NOTICE
The use of non genuine wheels will
cause the tire pressure sensors to
transmit the electronic code in dif-
ferent manner, resulting in the fail-
ure of the system.
The use of tires other than origi-
nally installed with genuine wheels
may also cause the malfunction of
the system.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.
NOTICE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable protec-
tion against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the instruc-
tions, may cause harmful interference to
radio communications. However, there is
no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interfer-
ence to radio or television reception,
which can be determined by turning the
equipment off and on, the user is en-
couraged to try to correct the interfer-
ence by one or more of the following
measures: