stop start TOYOTA LAND CRUISER 2008 J200 Owners Manual

26
1−2. Opening, closing and locking the doors
Smar t key system
The following operations can be pe rformed simply by carrying the
electronic key on your person, for example in your pocket.
Locks and unlocks the side doors ( P. 27)
Locks and unlocks the back door ( P. 48)
Starts and stops the engine (
P. 149)
ITY12C002

29
1−2. Opening, closing and locking the doors
1
Before driving
nEffective range (areas within which the electronic key is
detected)
When locking or unlock−
ing the doors
The system can be oper−
ated when the electronic
key is within about 2.3 ft.
(0.7 m) of an outside door
handle.
When starting the engine
or changing “ENGINE
START STOP” switch
modes
The system can be oper−
ated when the electronic
key is inside the vehicle.

31
1−2. Opening, closing and locking the doors
1
Before driving
nSwitching the door unlock function
If it is possible to set which doors the entry function unlocks.
Turn the “ENGINE START STOP” switch OFF.
When the indicator on the key surface is turned off, press and hold
, or for approximately 5 seconds while pressing
on the key.
The setting changes each time an operation is preformed, as shown below.
(When changing the setting continuously, release the buttons, wait for at least
5 seconds, and repeat step 2.)
STEP1
STEP 2
Multi−information
displayUnlocking function Beep
Hold the driver ’s door han−
dle to unlock only the
driver ’s door.Exterior: Beeps three
times
Interior: Pings once
Hold either door handle to
unlock all doors.
Exterior: Beeps twice
Interior: Pings once

33
1−2. Opening, closing and locking the doors
1
Before driving
nNote for the smart key system
lEven when the electronic key is within the effective range (detection
areas), the system may not operate properly in the following cases.
The electronic key is too close to the window or outside door handle,
near the ground, or in a high place when the doors are locked or
unlocked.
The electronic key is near the ground or in a high place, or too close to
the rear bumper center when the back door is locked or unlocked.
The electronic key is on the instrument panel, floor or in the glove box
when the engine is started or “ENGINE START STOP” switch modes
are changed.
lAs long as the electronic key is within the effective range, the doors may
be locked or unlocked by anyone.
lEven if the electronic key is not inside the vehicle, it may be possible to
start the engine if the electronic key is near the window.
lThe doors may unlock if a large amount of water splashes on the door
handle, such as in the rain or in a car wash. (The doors will automatically
be locked after approximately 60 seconds if the doors are not opened
and closed.)
lGripping the door handle when wearing a glove may not unlock the door.
lIf the wireless remote control is used to lock the doors when the elec−
tronic key is near the vehicle, there is a possibility that the door may not
be unlocked by the smart key system. (Use the wireless remote control to
unlock the doors.)
lA sudden approach to the effective range or door handle operation may
prevent the doors from being unlocked.
In this case, return the door han−
dle to the original position and check that the doors unlock before pulling
the door handle.
nWhen the vehicle is not driven for extended periods
To prevent theft of the vehicle, do not leave the electronic key within 6 ft. (2
m) of the vehicle.
nSecurity feature
If a door is not opened within approximately 60 seconds after the vehicle is
unlocked, the security feature automatically locks the vehicle again.

34 1−2. Opening, closing and locking the doors
nAlarms and warning indicators
A combination of exterior and interior alarms as well as warnings displayed
on the multi−information display are used to prevent theft of the vehicle and
unforeseeable accidents resulting from erroneous operation. Perform the
appropriate correction procedure de
scribed in the following table.
AlarmSituation Correction procedure
Exterior alarm
sounds once for
2 secondsAn attempt was made to
lock the doors using the
entry function while the
electronic key was still
inside the passenger com−
partmentRetrieve the elec−
tronic key from the
passenger compart−
ment and lock the
doors again
Exterior alarm
sounds once for
60 secondsAn attempt was made to
exit the vehicle and lock
the doors without first turn−
ing the “ENGINE START
STOP” switch OFFTurn the “ENGINE
START STOP” switch
OFF and lock the
doors again
Exterior alarm
sounds once for
10 secondsAn attempt was made to
lock the vehicle while a
door is openClose all of the doors
and lock the doors
again
Interior alarm
pings continu−
ously
*1
The “ENGINE START
STOP” switch was turned
to ACCESSORY mode
while the driver ’s door was
open (or the driver ’s door
was opened while the
“ENGINE START STOP”
switch was in ACCES−
SORY mode)Turn the “ENGINE
START STOP” switch
OFF and close the
driver ’s door
The “ENGINE START
STOP” switch was turned
OFF while the driver ’s door
was open
Close the driver ’s
door

35
1−2. Opening, closing and locking the doors
1
Before driving
AlarmSituation Correction procedure
Interior alarm
sounds continu−
ously
*1
When the “ENGINE
START STOP” switch is in
IGNITION ON or ACCES−
SORY mode, an attempt
was made to open the
door and exit the vehicle,
and the shift lever was not
in “P”Shift the shift lever to
“P” and turn the
“ENGINE START
STOP” switch OFF
Interior and exte−
rior alarms sound
continuously
*1
When the “ENGINE
START STOP” switch is in
IGNITION ON or ACCES−
SORY mode, the driver ’s
door was closed after the
key was carried outside
the vehicle, and the shift
lever not in “P”Shift the shift lever to
“P”, turn the “ENGINE
START STOP” switch
OFF and close the
driver ’s door again
Interior alarm
pings once
*1
The electronic key has a
low batteryReplace the electronic
key battery
An attempt was made to
start the engine without the
electronic key being
present, or the electronic
key was not functioning
normallyStart the engine with
the electronic key
present*
2

36 1−2. Opening, closing and locking the doors
*1: A message will be shown on the multi−information display in the instru−
ment cluster.
*2: If the engine does not start when the electronic key is inside the vehicle,
the electronic key battery may be depleted or there may be difficulties
receiving signal front the key. (
P. 481)
nIf the smart key system does not operate properly
l
Locking and unlocking the doors: Use the mechanical key. ( P. 481)
lStarting the engine: P. 150
n
P. 410
nCustomization that can be configured at Toyota dealer
Settings (e.g. smart key system) can be changed. (Customizable features
P. 519)
AlarmSituation Correction procedure
Interior alarm
pings once and
exterior alarm
sounds 3 times
*1
The driver ’s door was
closed after the key was
carried outside the vehicle,
and the “ENGINE START
STOP” switch was not
turned OFFTurn the “ENGINE
START STOP” switch
OFF and close the
driver ’s door again
An occupant carried the
electronic key outside the
vehicle and closed the
door while the “ENGINE
START STOP” switch was
not OFF
Bring the electronic
key back into the vehi−
cle

44 1−2. Opening, closing and locking the doors
Locking the driver ’s doors from the outside without a key
Move the inside lock button to the lock position.
Close the door.
The door cannot be locked if the “ENGINE START STOP” switch is in
ACCESSORY or IGNITION ON mode, or the electronic key is left
inside the vehicle.
The key may not be detected correctly and the door may be locked.
Rear door childprotector lock
The door cannot be opened from
inside the vehicle when the locks
are set.
These locks can be set to prevent
children from opening the rear
doors. Press down rear door
switches to lock the rear doors.
STEP1
STEP 2
ITY12C032

45
1−2. Opening, closing and locking the doors
1
Before driving
Automatic door locking and unlocking systems
The following functions can be set or canceled:
nSetting and canceling the functions
To switch between setting and canceling, follow the procedure
below:
Close all the doors and switch the “ENGINE START STOP”
switch IGNITION ON mode. (Perform step 2 within 20 sec−
onds.)
Shift the shift lever to “P” or “N”,
press and hold the driver ’s door
lock switch (
or) for 5 sec−
onds then release.
The shift lever and switch posi−
tions corresponding to the
desired function to be set or can−
celed are shown as follows.
Function Operation
Shift position linked
door locking functionShifting the shift lever out of “P” locks all
doors.
Shift position linked
door unlocking functionShifting the shift lever to “P” unlocks all
doors.
Speed linked door lock−
ing functionAll doors are locked when the vehicle speed is
approximately 12 mph (20 km/h) or higher.
Driver ’s door linked door
unlocking function
All doors are unlocked when the driver ’s door
is opened within 10 seconds after turning the
“ENGINE START STOP” switch OFF.
STEP1
STEP 2

63
1−3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before performing
the following:
Using the wireless remote control
Turn the “ENGINE START STOP” switch to OFF and close
the driver ’s door.
While pressing the desired but−
ton (“1”, “2” or “3”), press
on the wireless remote control
until the signal beeps.
The driving position is recalled
when the driver ’s door is
unlocked using the entry function
or wireless remote control and the
driver ’s door is opened.
STEP1
1SET23
ITY13C130
STEP2
nCanceling the linked door unlock operation
Turn the “ENGINE START STOP” switch to OFF and close the
driver ’s door.
Using the wireless remote control: While pressing “SET” button,
press button on the wireless remote control until the signal
beeps.
STEP1
STEP 2