clock setting TOYOTA MATRIX 2003 E130 / 1.G Owners Manual

’03 MATRIX_U (L/O 0201)
1112003 MY COROLLA MATRIX_U (OM12767U)
Alternate Frequency
To turn the AF mode on, push and hold
the “AM/FM” button until you hear a beep.
“AF ON” will appear on the display.
When reception condition worsen, the au-
dio system will select the RDS station
which has the same PI (Program Identifi-
cation) code.
To turn the AF mode off, push and hold
the “AM/FM” button again until you hear
a beep. “AF OFF” will appear on the dis-
play.
BAL/FADE (Sound balance adjustment
function)
This button is used to adjust the sound
balance between the front and rear, and
the right and left speakers.
For front/rear adjustment, push the “BAL/
FADE” button repeatedly until “FAD” ap-
pears on the display. Then turn the
“TUNE/SELECT” knob to adjust the front/
rear balance.
For left/right adjustment, push the “BAL/
FADE” button repeatedly until “BAL” ap-
pears on the display. Then turn the
“TUNE/SELECT” knob to adjust the left/
right balance.To return to the middle position balances,
push and hold the “BAL/FADE” button for
two seconds.
CD/AUX (Compact Disc/Auxiliary)
Push the “CD/AUX” button to switch from
radio to compact disc operation. A disc
must already be loaded in the player.
Error codes
If the player malfunctions, your audio sys-
tem will display the following error mes-
sages.
“CHECK CD”:
The road is too rough. The disc should
play when the road is smoother.
The disc is dirty, scratched, wet or
upside down.
The air is very humid. If so, wait about
an hour and try again.
If the disc is not playing correctly, for any
other reason, try a known good compact
disc.
“PLAYER ERROR”: There is trouble in-
side the system. Eject the disc. Set the
disc again.
If malfunction is not rectified, take your
vehicle to your Toyota dealer. EQ (Equalizer)
Your audio system can store five different
EQ settings so that you will not need to
readjust it every time you listen to a dif-
ferent program.
To use a preset setting:
Push the “EQ” button repeatedly until the
EQ number you want to use appears on
the display.
To change a preset EQ setting:
1. Use the “TONE” button and the “TUNE/SELECT” knob to select the
desired equalization. (For details, see
“TONE”.)
2. Push and hold the “EQ” button until “SELECT EQ #” appears on the dis-
play.
3. Push the “EQ” button repeatedly or turn the “TUNE/SELECT” knob to select
the desired preset EQ number.
4. Push and hold the “EQ” button until “EQ SAVED” appears on the display
and you hear a beep. This EQ setting
is saved to that number.
HR/MIN (Hours/minutes adjustment)
These buttons are used to adjust the
clock time. (For details, see “Clock” on
page 150 in Section 19.)

’03 MATRIX_U (L/O 0201)
11 32003 MY COROLLA MATRIX_U (OM12767U)
To turn off an interrupt while the radio in
on the PTY mode, select the program type
marked with an asterisk. Push and hold
“PROG TYPE” until you hear a beep. The
asterisk will disappear.
Note: ALERT! is a special program type
interrupt that is always on. If an emergen-
cy broadcast is received during reception
of anything other than AM broadcasting,
“ALERT” appears on the display and the
system adjust the volume to the interrupt
volume.
Setting a PTY station
Program types can be stored to the preset
buttons. For details, see “1 2 3 4 5 6
(Preset buttons)”.
Seeking a PTY station
If the radio in on the PTY mode, it will
find and play the next station up or down
the station band within the same program
type. If no PTY station will be found,
“NOT FOUND” will appear on the display
and the radio will return to the previous
frequency.
For details, see “SEEK”.Scanning a PTY station
If the radio in on the PTY mode, it will
tune in the next station within the same
program type.
For details, see “SCAN”.
PWR/VOL (Power/Volume)
Push “PWR/VOL” to turn the audio system
on and off. Turn “PWR/VOL” to adjust the
volume.
RCL (Recall)
This button is designed to change the dis-
play in each mode.
You can also display the clock by pushing
this button when the ignition switch is off.
Radio
Push the “RCL” button to change the dis-
play among the frequency, program ser-
vice name and program type name when
RDS station is being received.
To change what is normally shown on the
display, push this button repeatedly until
you see the display you want, then hold
this button until the display flashes and
you hear a beep.Compact disc player
Push the “RCL” button to change the dis-
play between the track number and
elapsed time.
To change what is normally shown on the
display, push this button repeatedly until
you see the display you want, then hold
this button until the display flashes and
you hear a beep.
RDM (Random)
Push the “RDM” button to listen the tracks
on the disc in random order. “RDM” will
appear on the display. To turn off the
random feature, push this button again.
SCAN
Radio
You can either scan all the frequencies on
a band or scan only the preset stations
for that band.
To scan the preset stations:
Push and hold either side of the “SEEK/
SCAN” button for more than 4 seconds.
“P SCAN” will appear on the display and
you hear two beeps. The radio will tune
in the next preset station up the band,
stay there for 5 seconds, and then move
to the next preset station. To cancel scan
and remain on the current station, push
this button again.

’03 MATRIX_U (L/O 0201)
11 52003 MY COROLLA MATRIX_U (OM12767U)
After the traffic announcement program is
over, the display returns to the previous
mode.
If no traffic program station is found, “No
Traffic” will appear on the display for 5
seconds and the display returns to the
previous mode. If the “TRAF” button is
pushed when the compact disc player is
on, the radio will start seeking traffic pro-
gram stations. Audio source will change
only if there is a traffic announcement.
When a “TA” is received, the radio stores
the volume of the previous mode and ad-
justs the volume to the previous interrupt
volume. During the traffic announcement,
you can adjust the volume using the
“PWR/VOL”.
The adjusted volume will be used as the
new default interrupt volume. The interrupt
volume has a minimum default setting.
The stored interrupt volume will be the
greater of the current volume and the
minimum default setting. After an interrupt,
the radio system will return to the volume
that was active before the interrupt.TUNE (Tuning)
Your Toyota has an electronic tuning radio
(ETR). Turn the knob clockwise to step up
the frequency. Turn the knob counterclock-
wise to step down the frequency.

’03 MATRIX_U (L/O 0201)
11 92003 MY COROLLA MATRIX_U (OM12767U)
“PLAYER ERROR”: There is trouble in-
side the system. Eject the disc. Set the
disc again.
If malfunction is not rectified, take your
vehicle to your Toyota dealer.
Dolby 
B NR∗
If you are listening to a tape that was
recorded with Dolby  B Noise Reduction,
push “
”. “DOLBY NR ON” will appear
on the display. Push the button again to
turn off Dolby  B NR. “DOLBY NR OFF”
will appear on the display.
The Dolby NR mode reduces tape noise
by about 10 dB. For best sound reproduc-
tion, play your tapes with this button on
or off according to the mode used for
recording the tape.
∗: Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation. “DOLBY” and the
double D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
EQ (Equalizer)
Your audio system can store five different
EQ settings so that you will not need to
readjust it every time you listen to a dif-
ferent program.
To use a preset setting:
Push the “EQ” button repeatedly until the
EQ number you want to use appears on
the display.
To change a preset EQ setting:
1. Use the “TONE” button and the “TUNE/ SELECT” knob to select the desired
equalization. (For details, see “TONE”.)
2. Push and hold the “EQ” button until “SELECT EQ #” appears on the dis-
play.
3. Push the “EQ” button repeatedly or turn the “TUNE/SELECT” knob to select
the desired preset EQ number.
4. Push and hold the “EQ” button until “EQ SAVED” appears on the display
and you hear a beep. This EQ setting
is saved to that number. HR/MIN (Hours/minutes adjustment)
These buttons are used to adjust the
clock time. (For details, see “Clock” on
page 150 in Section 19.)
INFO (Information)
When an RDS radio station transmits a
text message, “INFO” will be displayed. At
this time, push the “INFO” button to view
the text message. If the whole message
does not appear on the display, part of
the message will appear every three sec-
onds until the message is completed. To
scroll through the message at your own
speed, push the “INFO” button consecu-
tively. When the whole message has been
displayed, the message will disappear.
The message display will be canceled if
any button that affects the display is
pushed. To view the message again, push
the “INFO” button again.
The RDS audio system saves a message
until a new message is received.
If the text message is not available when
you push “INFO” button, “NO INFO” will
appear on the display.

’03 MATRIX_U (L/O 0201)
1242003 MY COROLLA MATRIX_U (OM12767U)
TRAF (Traffic)
This button turns the traffic announcement
(TA) feature on and off.
By pushing the “< >” button, “TRAF” ap-
pears on the display and the radio will
start seeking any traffic program station.
When a traffic program station is found,
“TRAF” will be displayed (). If no
traffic program stations are found, “No
Traffic” will appear on the display.
After the traffic announcement program is
over, the display returns to the previous
mode.
If no traffic program station is found, “No
Traffic” will appear on the display for 5
seconds and the display returns to the
previous mode. If the “TRAF” button is
pushed when the cassette player or the
compact disc player is on, the radio will
start seeking traffic program stations. Au-
dio source will change only if there is a
traffic announcement.
When a “TA” is received, the radio stores
the volume of the previous mode and ad-
justs the volume to the previous interrupt
volume. During the traffic announcement,
you can adjust the volume using the
“PWR/VOL”.The adjusted volume will be used as the
new default interrupt volume. The interrupt
volume has a minimum default setting.
The stored interrupt volume will be the
greater of the current volume and the
minimum default setting. After an interrupt,
the radio system will return to the volume
that was active before the interrupt.
TUNE (Tuning)
Your Toyota has an electronic tuning radio
(ETR). Turn the knob clockwise to step up
the frequency. Turn the knob counterclock-
wise to step down the frequency.

’03 MATRIX_U (L/O 0201)
1302003 MY COROLLA MATRIX_U (OM12767U)
Ta l k
Rock
Cls Rck (Classic rock)
Adlt Hit (Adult Hits)
Soft Rck
To p 4 0
Country
Oldies
Soft
Nostalga (Nostalgia)
Jazz
classicl (Classical)
R & B
Soft R & B
Language
Rel Musc (Religious Music)
Rel Talk (Religious Talk)
Persnlty (Personality)
Public
College
WeatherInterrupt function
If the radio in on the compact disc mode,
the radio will switch to the FM band with
the previous interrupt volume. The pro-
gram type and “Int” will appear. If the
radio in on the FM mode, the volume will
be adjusted to the previous interrupt vol-
ume. To cancel the interrupt function,
press “P·TYPE” or the selected mode but-
ton.
If the radio in on the PTY mode, program
types, except Any Type, may be selected
as interrupts. To set a program type as an
interrupt, push and hold “P·TYPE” while a
program type is displayed until you hear
a beep. The asterisk will appear when an
interrupt is set.
To turn off an interrupt while the radio in
on the PTY mode, select the program type
marked with an asterisk. Push and hold
“P·TYPE” until you hear a beep. The as-
terisk will disappear.
Note: ALERT! is a special program type
interrupt that is always on. If an emergen-
cy broadcast is received during reception
of anything other than AM broadcasting,
“ALERT” appears on the display and the
system adjust the volume to the interrupt
volume. Setting a PTY station
Program types can be stored to the preset
buttons. For details, see “1 2 3 4 5 6
(Preset or disc selection buttons)”.
Seeking a PTY station
If the radio is in the PTY mode, it will find
and play the next station up or down the
station band within the same program
type. If no PTY station will be found,
“NOT FOUND” will appear on the display
and the radio will return to the previous
frequency.
For details, see “SEEK”.
Scanning a PTY station
If the radio is in the PTY mode, it will
tune in the next station within the same
program type.
For details, see “SCAN”.
RCL (Recall)
This button is designed to change the dis-
play in each mode. You can also display
the clock by pushing this button when the
ignition switch is off.

’03 MATRIX_U (L/O 0201)
1342003 MY COROLLA MATRIX_U (OM12767U)
TRAF (Traffic)
This button turns the traffic announcement
(TA) feature on and off.
By pushing “< >” button, “TRAF” appears
on the display and the radio will start
seeking any traffic program station.
When a traffic program station is found,
“TRAF” will be displayed (). If no
traffic program stations are found, “No
Traffic” will appear on the display.
After the traffic announcement program is
over, the display returns to the previous
mode.
If no traffic program station is found, “No
Traffic” will appear on the display for 5
seconds and the display returns to the
previous mode. If the “TRAF” button is
pushed when the compact disc player is
on, the radio will start seeking traffic pro-
gram stations.
When a “TA” is received, the radio stores
the volume of the previous mode and ad-
justs the volume to the previous interrupt
volume. During the traffic announcement,
you can adjust the volume using the
“PWR/VOL”.The adjusted volume will be used as the
new default interrupt volume. The interrupt
volume has a minimum default setting.
The stored interrupt volume will be the
greater of the current volume and the
minimum default setting. After an interrupt,
the radio system will return to the volume
that was active before the interrupt.
TUNE (Tuning)
Your Toyota has an electronic tuning radio
(ETR). Turn the knob clockwise to step up
the frequency. Turn the knob counterclock-
wise to step down the frequency.NOTICE
To ensure correct audio system op-
erations:

Be careful not to spill beverages
over the audio system.
 Do not put anything other than a
cassette tape or Compact Disc into
the slot.
 The use of a cellular phone inside
or near the vehicle may cause a
noise from the speakers of the au-
dio system which you are listening
to. However, this does not indicate
a malfunction.
RADIO RECEPTION
Usually, a problem with radio reception
does not mean there is a problem with
your radio—it is just the normal result of
conditions outside the vehicle.
For example, nearby buildings and terrain
can interfere with FM reception. Power
lines or telephone wires can interfere with
AM signals. And of course, radio signals
have a limited range. The farther you are
from a station, the weaker its signal will
be. In addition, reception conditions
change constantly as your vehicle moves.
Car audio system operating
hints

’03 MATRIX_U (L/O 0201)
1502003 MY COROLLA MATRIX_U (OM12767U)
Ty p e A
Ty p e B
The digital clock indicates the time
when the key is in the “ACC” or “ON”
position. Even when the ignition switch
is off, you can turn on the clock dis-
play for a few seconds by pushing the
“RCL” button.
Type A—To set the time, push and hold
the “HR” or “MIN” button until the “:”
starts flashing. Then set the time by push-
ing the “HR” (hour) and the “MIN” (minute)
buttons. If the time is before 12 noon,
“AM” appears on the display when the
time being set.
Type B—To set the time, push and hold
the “H” or “M” button until the “:” starts
flashing. Then set the time by pushing the
“H” (hour) and the “M” (minute) buttons.
When the time is being set, “AM” or “PM”
appears on the display.
RDS CLOCK UPDATE FUNCTION
You can update the clock with RDS
(Radio Data System) data. Push and hold
the “HR” and “MIN” (type A) or “H” and
“M” (type B) buttons at least 2 seconds
while receiving an RDS station. “TIME
UPDATED” will appear on the display with
a beep and the clock will be updated. If
setting could not be completed
successfully, “NO UPDATED” will appear
on the display.
CIGARETTE LIGHTER
To use the cigarette lighter, press it in.
After it finishes heating up, it automati-
cally pops out ready for use.
If the engine is not running, the key must
be in the “ACC” position.
Do not hold the cigarette lighter pressed
in.
Use a Toyota genuine cigarette lighter or
equivalent for replacement.
ClockCigarette lighter and portable
ashtray