TOYOTA MR2 SPYDER 2000 Owners Manual (in English)

MR2 U
1982000 MR2 (OM17475U)
Checking and replacing fuses
SB73035
GoodBlown
Ty p e A
SB73036
Good Blown
Ty p e B
SB73037
Good Blown
Ty p e C
SB73042
If the headlights or other electrical
components do not work, check the
fuses. If any of the fuses are blown,
they must be replaced.
See Fuse locations" in Section 7−1 for
locations of the fuses.
Turn the ignition switch and inoperative
component off. Pull a suspected fuse
straight out and check it.
Determine which fuse may be causing the
problem. The lid of the fuse box shows
the name of the circuit for each fuse. See
Section 8 of this manual for the functions
controlled by each circuit.
Type A fuses can be pulled out by the
pull−out tool. The location of the pull−out
tool is shown in the illustration.

MR2 U
1992000 MR2 (OM17475U)
If you are not sure whether the fuse has
blown, try replacing the suspected fuse
with one that you know is good.
If the fuse has blown, push a new fuse
into the clip.
Only install a fuse with the amperage rat-
ing designated on the fuse box lid.
If you do not have a spare fuse, in an
emergency you can pull out the D P/W",
P P/W" or CIG" fuse, which may be
dispensable for normal driving, and use it
if its amperage rating is the same.
If you cannot use one of the same amper-
age, use one that is lower, but as close
as possible to the rating. If the amperage
is lower than that specified, the fuse
might blow out again but this does not
indicate anything wrong. Be sure to get
the correct fuse as soon as possible and
return the substitute to its original clip.
It is a good idea to purchase a set of
spare fuses and keep them in your ve-
hicle for emergencies.
If the new fuse immediately blows out,
there is a problem with the electrical sys-
tem. Have your Toyota dealer correct it as
soon as possible.CAUTION
Never use a fuse with a higher am-
perage rating, or any other object, in
place of a fuse. This may cause ex-
tensive damage and possibly a fire.
Adding washer fluid
SB73003
If any washer does not work, the wash-
er tank may be empty. Check the wash-
er fluid level on the level gauge. If the
washer fluid level is below LOW", add
washer fluid.
You may use plain water as washer fluid.
However, in cold areas where tempera-
tures range below freezing point, use
washer fluid containing antifreeze. This
product is available at your Toyota dealer
and most auto parts stores. Follow the
manufacturer ’s directions for how much to
mix with water.

MR2 U
2002000 MR2 (OM17475U)
NOTICE
Do not use engine antifreeze or any
other substitute because it may dam-
age your vehicle’s paint.
Replacing light bulbs
The following illustrations show how to
gain access to the bulbs. When replacing
a bulb, make sure the ignition switch and
light switch are off. Use bulbs with the
wattage ratings given in the table.
CAUTION
Halogen bulbs have pressurized gas
inside and require special handling.
They can burst or shatter if scratched
or dropped. Hold a bulb only by its
plastic or metal case. Do not touch
the glass part of a bulb with bare
hands.
NOTICE
Only use a bulb of the listed type.
Light bulbsBulbNo.WTy p e
Headlights60/55A
Parking lights5B
Front turn signal
lights21B
Front side marker
lights3.8B
Rear turn signal
lights21C
Stop/tail lights21/5B
Stop lights21B
Back−up lights21B
License plate lights5B
Interior light8D
High mounted stop
light5B
A: HB2 halogen bulbs
B: Wedge base bulbs
C: Single end bulbs
D: Double end bulbs

MR2 U
2012000 MR2 (OM17475U)
SB73064
BEFORE REPLACING LIGHT BULBS
Replacing headlights, parking lights and
front turn signal lights.1. Remove the front box cover.
Use a philips− head screwdriver.
SC73006
2. Remove the cover in the trunk.
Remove and install the cover clips as
shown in the following illustrations.

MR2 U
2022000 MR2 (OM17475U)
SC18005
Removing clips
SC18006
Installing clips
Headlights
SB73043
1. Unplug the connector. Remove therubber cover.
If the connector is tight, wiggle it.
SB73044
2. Release the bulb retaining spring and remove the bulb. Install a new
bulb and the bulb retaining spring.
To install a bulb, align the tabs of the
bulb with the cutouts of the mounting
hole.

MR2 U
2032000 MR2 (OM17475U)
SB73006
3. Install the rubber cover as shownand snuggle on the boss. Insert the
connector.
Make sure the rubber cover fits snugly on
the connector and the headlight body.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.
Parking lights
SB73046
SB73047
Front turn signal lights
SB73048
SB73049

MR2 U
2042000 MR2 (OM17475U)
Front side marker lights
SB73045
Phillips−head screw: Use a ph illips−head
screwdriver.
Cover clip: Remove and install the cover
clips as shown in the following illustra-
tions.
SB73033
Removing clips
SB73034
Installing clips
SB73013
SB73014

MR2 U
2052000 MR2 (OM17475U)
SB73019SB73065
a: Back−up light
b: Rear turn signal light
c: Stop/tail light
d: Stop light
CAUTION
Be careful when you work in the area
around the engine after driving in or-
der to prevent burning yourself. The
engine hood, the support rod, or sur-
rounding area could be hot after driv-
ing.
License plate lights
SB73021
SB73022
Rear turn signal, stop/tail,
stop and back−up lights

MR2 U
2062000 MR2 (OM17475U)
SB73023
High mounted stop light
SB73062
SB73052
SB73060
SB73057

MR2 U
2072000 MR2 (OM17475U)
SB73058
SB73059
CAUTION
Be careful when you work in the area
around the engine after driving in or-
der to prevent burning yourself. The
engine hood, the support rod, or sur-
rounding area could be hot after driv-
ing.