driver TOYOTA RAIZE 2023 Service Manual

1994-3. Operating the lights and windshield wipers
RAIZE_OM_General_BZ358E✽
: If equipped
Driving
4
Follow me home system✽
This system allows the headlights to be turned on for 30 seconds when
the engine switch is turned off.
Pull the lever toward you and
release it with the light switch
in after turning the engine switch
off.
The lights are turned off in the following
situations.
⦁ The engine switch is turned to “ON”.
⦁ The light switch is turned on.
⦁ The light switch is pulled toward you
and then released.
⬛Daytime running light system✽
To make your vehicle more visible to ot her drivers during daytime driving, the
daytime running lights turn on automatically whenever the engine is started
and the parking brake is released wi th the headlight switch in the or
* position. (Illuminate brighter than the front position lights.) Daytime
running lights are not designed for use at night.
*When the front position lights are not turned on
⬛Light sensor✽
⚫Observe the following precautions.
Failure to do so may prevent the
automatic light on/off function from
working normally.
⦁ Avoid placing any item on the
sensor or pasting items that
would block the sensor on the
windshield
⦁ Do not spray liquid including
glass cleaner
KBRO430103E
KBRO430104E
Light sensor
(with solar radiation sensor)
RAIZE_OM_General_BZ358E.book 199 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2004-3. Operating the lights and windshield wipers
RAIZE_OM_General_BZ358E
✽: If equipped
⬛Automatic light off system
⚫While the lights are turned on, changi ng the engine switch from “ON” to
“ACC” or “OFF” will automatically turn off the lit lights.
⚫To turn the lights on again, turn “ON” the engine switch or move the head-
light switch to the position, and then move it to the or
position.
⬛Automatic light-off warning buzzer
When the headlights and tail lights are tu rned on with the engine switch set to
“ACC” or “OFF”, opening the driver’s door will cause the warning buzzer to
sound, letting the driver know that the lights have not been turned off.
⚫When the buzzer sounds , the warning message also appears for vehicles
with TFT color multi-information display. ( ➞P. 391)
⬛Power saving function
To prevent the battery from discharging, when the engine switch is set in “ACC”
or “OFF” and the headlights or tail lig hts are on, the power saving function is
activated and all lights are automatically turned off after about 10 minutes.
After light has been automatically turn ed off, perform any of the following
operations to cancel the power saving state and turn the lights back on.
⚫
When the engine switch is set to “ON”
⚫When the headlight switch is operated (However, the lights will turn off again
automatically after about 10 minutes)
⚫When one of the doors is opened or cl osed (However, the lights will automati-
cally turn off again after about 10 minutes)
⬛Customizations✽
You can change the timing of the headlight switch turning on and off automat-
ically at the position, etc.
(List of customizable features: ➞ P. 430)
NOTICE
⬛To prevent battery discharge
Do not leave the lights on for a long ti me with the engine stopped. Also, be
sure to turn off the lights when you leave the vehicle.
RAIZE_OM_General_BZ358E.book 200 ページ ２０２２年５月１７日　火曜日　午後１時５９分

211
RAIZE_OM_General_BZ358E✽
: If equipped
Driving
4
4-5. Using the driving support systems
BSM (Blind Spot Monitor)✽
Overview of Blind Spot Monitor
Blind Spot Monitor has the 2 functions.
⚫BSM (Blind Spot Monitor) function
Assists the driver in making decisions when changing lanes.
⚫RCTA (Rear Cross Traffic Alert) function
Assists the driver when backing up.
These functions use the same sensors.
a TFT color multi-information display
The BSM function or the RCTA function can be switched ON and OFF.
bOutside rear view mirror indicators
Installed on the outside rear view mirrors. When they detect a vehicle approaching
from behind, they light up or start flashing.
BSM function: When a vehicle is detected in the blind spot area of the outside rear
view mirrors or when a vehicle rapidly approaching into the blind spot area is
detected from the behind, it lights up the outside rear view mirror indicator of the
side that detected the vehicle. When you have moved the turn signal lever to the
side where the vehicle is detected, the outside rear view mirror indicators start
flashing.
RCTA function: When a vehicle approaching from the right or left rear end of your
vehicle is detected, both of the outside rear view mirror indicators start flashing.
c BSM OFF indicator/RCTA OFF indicator
When you turn off the BSM function, the BSM OFF indicator lights up.
When you turn off the RCTA function, the RCTA OFF indicator lights up.
4
322
1
KBRO460501E
RAIZE_OM_General_BZ358E.book 211 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2124-5. Using the driving support systems
RAIZE_OM_General_BZ358E
dBuzzer
BSM buzzer: When you have moved the turn signal lever to the side where the vehi-
cle is detected, the buzzer will sound.
RCTA Buzzer: When a vehicle approaching from the right or left rear end of your
vehicle is detected, the buzzer will sound.
WARNING
⬛To use the BSM function safely
The driver is responsible for driving the vehicle safely. It is th e driver’s responsi-
bility to be aware of the situations around the vehicle and drive safely.
The BSM function is an auxilia ry system designed to let the driver know of the
presence of a vehicle that has entere d or is rapidly approaching toward the
blind spot area of the outside rear view mirrors. Since this system alone is not
sufficient for determining the feasibility of changing lanes, overly relying on the
system could lead to an unforeseen accid ent, resulting in serious injury or
death.
This system does not work effectively depending on the circumstances. The
driver is responsible for checking the safety around the vehicle by using his/
her own eyes and the mirrors.
⬛To use the RCTA function safely
The driver is responsible for driving the vehicle safely. It is th e driver’s responsi-
bility to be aware of the situations around the vehicle and drive safely.
The RCTA function is an auxiliary system designed to let the driver know of the
presence of a vehicle that is approaching from the right or left rear of the vehi-
cle.
Even with the RCTA function enabled, this system does not work effectively
depending on the circumstances. The dr iver is responsible for checking the
safety around the vehicle by using his/her own eyes.
Overly relying on the system could lead to an unforeseen accident, resulting in
serious injury or death.
RAIZE_OM_General_BZ358E.book 212 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2154-5. Using the driving support systems
RAIZE_OM_General_BZ358E
Driving
4
BSM function
The BSM function uses the radar sensors to detect vehicles traveling in
the next lane as described below and notifies the driver of the vehicles’
presence with the outside rear view mirror indicators and buzzers.
a A vehicle traveling in the area not re flected in the outside rear view mir-
rors (blind spot area)
b Vehicles rapidly approaching from behind into the area not reflected in
the outside rear view mirrors (blind spot area)
Detection range of the BSM function
The function detects a vehicle that has entered the area specified below.
a For both sides of the vehicle, an ar ea of approx. 3.5 m (11.5 ft.) from
approx. 0.5 m (1.6 ft.) away from the side surface
The function does not detect an area of a pprox. 0.5 m (1.6 ft.) from the side surface
of the vehicle toward the outside.
b Area approx. 1 m (3.3 ft.) ahead of the rear bumper
c Area approx. 3 m (9.8 ft.) behind the rear bumper
1
2
KBRO460503E
1
234
KBRO460504
RAIZE_OM_General_BZ358E.book 215 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2184-5. Using the driving support systems
RAIZE_OM_General_BZ358E
⦁When driving up and down on a series of steep slopes or driving on
dented areas of a road
⦁ When driving through a sharp curve or continuous curves, or driving in an
area with ups and downs
⦁ While the tires are slipping (spinning)
⦁ When there is not enough distance between your vehicle and the follow-
ing vehicle
⦁ When the vehicle has accessories such as a bicycle carrier installed in the
rear side
⦁ When the vehicle is causing rain or snow to whirl up behind
RCTA function
⬛Activation of the RCTA function
The RCTA function uses the radar sens ors to detect vehicles approaching
from the right or left rear of your ve hicle and notifies the driver of the vehi-
cles’ presence with the outside rear view mirror indicators and buzzers.
a Approaching vehicle
b Detection range of approaching vehicles
⬛Detection range of the RCTA function
The function detects a vehicle that has entered the area specified below.
1
22
1
KBRO460505
11
KBRO460506
RAIZE_OM_General_BZ358E.book 218 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2214-5. Using the driving support systems
RAIZE_OM_General_BZ358E✽
: If equipped
Driving
4
Front corner sensors✽/Reverse sensors✽
The front corner sensors and reverse sensors are the system that
uses the sonar to recognize the approximate distance between the
vehicle and the obstacle, and that notifies the driver of its presence
by the buzzer and display indica tors when the vehicle speed is
approx. 10 km/h (6 mph) or less.
Sonar positions and types
a Front sonar
The front corner sensors are used to
recognize necessary information.
bRear sonar
The reverse sensors are used to recog-
nize necessary information.
Switching front corner sensors and reverse sensors
(For vehicles with front corner sensors)
Press the switch
Pressing the switch turns on the front
corner sensors or reverse sensors and
lights up the switch-on indicator.
To turn it off, press the switch again.
How to display the front corner sensors or reverse sensors
Once an obstacle is recognized, they
are displayed automatically.
aFront corner sensor ON indicator
b Reverse sensor ON indicator
12KBRO451001E
KBRO451002E
11
22
KBRO451003E
RAIZE_OM_General_BZ358E.book 221 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2224-5. Using the driving support systems
RAIZE_OM_General_BZ358E
How to read the distance display
When an obstacle is recognized while all the activation conditions are sat-
isfied, the driver is notified of its presence by the buzzer and display indi-
cators.
⚫The buzzer will sound when the parking brake is not applied.
⚫When the distance to the obstacle becomes shorter, the buzzer and dis-
play indicators will change, as shown in the figure below.
▶Vehicles with multi-information display
▶Vehicles with TFT color multi-information display
⚫When sonar has recognized more than one obstacle simultaneously, the
buzzer for the closest obstacle will sound.
BuzzerDisplay
indicatorDistance between sonar and obstacle
FrontRear
A high-pitch intermit- tent beep continues
(intermittent sound)Approx. 60 to 45 cm (23 - 17 in.)Approx. 130 to 100 cm (51 - 39 in.)
A high-pitch short beep continues
(intermittent sound)Approx. 45 to 30 cm (18 - 12 in.)Approx. 100 to 50 cm (39 - 20 in.)
A high-pitch long beep
(continuous sound)Within approx. 30 cm (12 in.)Within approx. 50 cm (20 in.)
BuzzerDisplay
indicatorDistance between sonar and obstacle
FrontRear
A high-pitch intermit- tent beep continues
(intermittent sound)Approx. 60 to 45 cm (23 - 17 in.)Approx. 130 to 100 cm (51 - 39 in.)
A high-pitch short beep continues
(intermittent sound)Approx. 45 to 30 cm (18 - 12 in.)Approx. 100 to 50 cm (39 - 20 in.)
A high-pitch long beep
(continuous sound)Within approx. 30 cm (12 in.)Within approx. 50 cm (20 in.)
RAIZE_OM_General_BZ358E.book 222 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2324-5. Using the driving support systems
RAIZE_OM_General_BZ358E
Driving assist systems
The following devices automatically operate according to the driving
conditions to improve driving safety and performance. However,
these systems are supplementary and you should be careful not to
over-rely on them while driving.
◆ABS (Anti-lock Brake System)
Helps to prevent wheel lock when the brakes are applied suddenly, or if
the brakes are applied while driving on a slippery road surface.
◆Brake assist
Generates an increased level of braking force when the system detects a
panic stop situation.
◆VSC (Vehicle Stability Control)
Helps the driver to control skidding when swerving suddenly or turning on
slippery road surfaces.
◆TRC (Traction Control)
Helps to maintain drive power and pr event the drive wheels from spinning
when starting the vehicle or accelerating on slippery roads.
◆Hill-start assist control
Prevents the vehicle from moving backwards when starting on an uphill.
◆EPS (Electric Power Steering)
Uses an electric motor to assist steering operation.
◆Emergency brake signal
Emergency flashers automatically fl ash when braking suddenly, alerting
the following vehicle and reducing the possibility of a collision.
RAIZE_OM_General_BZ358E.book 232 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2354-5. Using the driving support systems
RAIZE_OM_General_BZ358E
Driving
4
⬛Activation conditions of the hill-start assist control
The system operates when all of the following conditions are met:
⚫Continuously variable transmission vehi cles: The shift lever is set to other
than P or N (when starting to move the vehicle forward or backward on an
uphill)
⚫Manual transmission vehicles: The shift lever is set to other than R when
starting to move the vehicle forward on an uphill or the shift lever is set to R
when starting to move the vehicle backward on an uphill
⚫Vehicle stopped state
⚫Not depressing the accelerator
⚫Parking brake is not applied
⬛Automatic deactivation of the hill-start assist control
The system is deactivated when one of the following occurs:
⚫Continuously variable transmission vehicl es: The shift lever is set to P or N
⚫Manual transmission vehicles: The shift lever is set to R when starting to
move the vehicle forward on an uphill or the shift lever is set to other than R
when starting to move the vehicle backward on an uphill
⚫The driver depresses the accelerator
⚫The driver applies the parking brake
⚫About 2 seconds have passed since releasing the brake pedal
⬛When the slip indicator turns on and the warning message ( ➞P. 389)
appears
It may indicate a malfunction in the systems. Contact your Toyota dealer.
⬛Activation conditions of the emergency brake signal
The system operates when all of the following conditions are met:
⚫The emergency flashers are not flashing
⚫The vehicle speed is 60 km/h (38 mph) or more
⚫The brake pedal is depressed and the vehicle is deemed to brake suddenly
based on the deceleration, or ABS is activated
⬛Automatic deactivation of the emergency brake signal
The system is deactivated when one of the following occurs:
⚫The emergency flashers were set to flashing
⚫The brake pedal was released
⚫It was determined that the vehicle did not brake suddenly based on the
deceleration
⚫ABS stopped working
RAIZE_OM_General_BZ358E.book 235 ページ ２０２２年５月１７日　火曜日　午後１時５９分