engine TOYOTA RAIZE 2023 Manual Online

2064-3. Operating the lights and windshield wipers
RAIZE_OM_General_BZ358E✽
: If equipped
⬛Operating conditions
When the engine switch is “ON”
⬛When the washer flui d does not come out
If the washer fluid does not come out even though the washer fluid tank level
is not low, check the nozzles for clogging.
⬛Reverse wiper function
While the windshield wiper is operating, setting the shift lever to R will move
the rear wiper several times. After the windshield wiper is stopped, setting the
shift lever to R within approximately 10 seconds will also move the rear wiper
several times.
⬛Customizations
The settings such as operation intervals can be modified.
(List of customizable features: ➞ P. 430)
(For some of the features, the settings can be changed from the setup screen
of the multi-info rmation display
✽: ➞ P. 9 1 )
(For some of the features, the settings can be changed from the setup screen
of the TFT color multi-information display
✽: ➞ P. 104)
NOTICE
⬛When the rear window is dry
Do not use the windshield wipers,
as they may damage the windshield.
⬛When the washer flui d does not come out
Do not operate the switch continually
as you may damage th e washer fluid pump.
⬛When a nozzle becomes clogged
When a nozzle becomes clogged, contact your Toyota dealer.
Do not try to clear it with a pin or other object.
The nozzle will be damaged.
⬛To prevent battery discharge
Do not leave the windshield wipers on longer than necessary when the engine
is not running.
RAIZE_OM_General_BZ358E.book 206 ページ ２０２２年５月１７日　火曜日　午後１時５９分

207
RAIZE_OM_General_BZ358E
Driving
4
4-4. Refueling
Opening the fuel tank cap
Perform the following steps to open the fuel tank cap:Before refueling the vehicle
⚫Close all the doors and windows, then turn the engine switch to “OFF”.
⚫Confirm the type of fuel.
⚫The side on which the fuel tank opening is mounted on the vehicle is
indicated on the meter.
▶Vehicles without TFT color multi-
information display (vehicles
without tachometer)▶Vehicles without TFT color multi-
information display (vehicles
with tachometer)
▶Vehicles with TFT color multi-
information display
⬛Fuel types
➞ P. 4 2 1
KBRO440112EKBRO440110
KBRO440111
RAIZE_OM_General_BZ358E.book 207 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2204-5. Using the driving support systems
RAIZE_OM_General_BZ358E
⬛Situations where the RCTA function may not work properly
⚫The RCTA function may not detect vehicles correctly in the following circumstances.
⦁The sensor positions or orientations are off due to a strong impact applied
to the sensors or the surrounding areas
⦁ The sensors or the rear bumper near the sensors are covered with mud,
snow, ice, or stickers
⦁ Driving on a wet road or driving in a puddle under bad weather conditions,
such as heavy rain, snow, or fog
⦁ When several vehicles are passing continuously behind your vehicle or
when a vehicle is approaching from th e opposite direction to the vehicle
detected first
⦁ When the vehicle is parked on a hill or an uneven road
⦁ When the vehicle has accessories such as a bicycle carrier installed in the
rear side
⦁ When the vehicle is moving backward on a steep hill with varying slopes
⦁ When the vehicle is parked diagonally
⦁ Right after turning on the RCTA function
⦁ Right after starting the engine wi th the RCTA function turned on
⦁ When being affected by radio wave interference from the radar sensors
installed on the vehicle parked next to your vehicle
⦁ When getting out from a sloped parking spot
⦁ When a large vehicle is parked next to your vehicle
⦁ When the vehicle is backing up at fast speed
⚫The RCTA function may have more unnecessary detections, especially in the
following circumstances.
⦁The sensor positions or orientations are off due to a strong impact applied
to the sensors or the surrounding areas
⦁ When another vehicle passes through the side of your vehicle
⦁ When the vehicle is traveling on a
road facing a parking lot
⦁ When metal objects (such as guardrails, walls, signs, parked vehicles) that
can easily reflect radio waves are located behind the vehicle
⦁ When the vehicle has accessories such as a bicycle carrier installed in the
rear side
⦁ When buildings or roadside walls are present in the direction to which the
vehicle is backing up
KBRO460508
RAIZE_OM_General_BZ358E.book 220 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2234-5. Using the driving support systems
RAIZE_OM_General_BZ358E
Driving
4
Sonar’s obstacle recognition range
The recognition areas are shown in
the right figure.
However, if the obstacle is too close
to the sonar, the recognition fails.
Depending on the obstacles’ shape
and conditions, the recognition
range may become shorter, or the
recognition may fail.
⬛Operating conditions
⚫Front corner sensors:
⦁When the engine switch is “ON”
⦁ When the front corner sensors/reverse sensors switch is ON
⦁ When the shift lever is set in other than P, and the vehicle speed is approx.
10 km/h or less
⚫Reverse sensors:
⦁When the engine switch is “ON”
⦁ Vehicles with front corner sensors:
When the front corner sensors/reverse sensors switch is ON
⦁ When the shift lever is set in R, and the vehicle speed is approx. 10 km/h or
less
⚫When an obstacle is recognized with all the activation conditions satisfied
and the parking brake not being applied, the buzzer will sound.
⬛Sonar recognition capabilities
⚫The sonar recognition range is limited to the area around the sonar on the
front side of the vehicle and th e rear bumper of the vehicle.
⚫It takes some time from when the sonar recognizes an obstacle until the
front corner sensors or reverse sensors become activated. If the vehicle gets
too close to the obstacle before the buzzers sounds, the buzzer may not
sound even when the vehicle is traveling at a slow speed.
⚫While the audio or air conditioning system is turned on, the music or fan
noise makes the buzzer sound difficult to hear.
KBRO451004E
RAIZE_OM_General_BZ358E.book 223 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2244-5. Using the driving support systems
RAIZE_OM_General_BZ358E
⬛When the high-pitch short beeps sound 3 times repeatedly and the front
corner sensor or reverse sensor ON indicator appears at 2 front locations
or 2 rear locations (or all 4 locations) simultaneously
⚫The front corner sensor or reverse se nsor functionality has been degraded.
When the front corner sensor or re verse sensor functionality temporarily
turns off, check if the sonar is not cove red with rain, snow, ice, or dirt. Remove
those attached to it, then wait for the f unctionality to be restored to normal.
⚫If the master warning light turns on at this time, it may indicate a malfunc-
tion of the system. Have the vehicle inspected at your Toyota dealer.
⚫Vehicles with TFT color multi-informati on display: Depending on the condi-
tions, the warning messages as “Son ar Sensor Function Stop” and “Sonar
Sensor Malfunction Visit Your Dealer” will be displayed.
⬛Front corner sensors and reverse sensors
In the following cases, the system ma y become activated even when there is
no obstacle within the operating range.
⚫When driving an area where the road slopes suddenly change
⚫When passing through plastic curtains or driving under flags
⚫When water splashes or drifting snow whirls up
⚫When passing an obstacle at close range
⚫When using an elevator for automobiles or using a mechanical parking lot
⚫When driving over a bump with an obstacle near the vehicle
⚫When there is an obstacle near the side of the vehicle
⚫When the road surface has large bumps, curbstones or protrusions, or when
the ground surface has tire tracks and holes
⚫When entering into a tight space
⚫During pouring rain or when water splashes over the vehicle
⚫Bad weather (heavy rain, snowstorm, fog, etc.)
⚫When the following is present near the vehicle: the sound of other vehicles’
horns, motorcycle engines, and air brakes of large vehicles, the devices emitting
ultrasonic waves, such as vehicle detect ors, or sonar systems of other vehicles
⚫When commercially available electrical components (such as an internally illu-
minated number plate, radio antenna) are installed near the sonar sensors
⚫When the vehicle body has been considerably tilted
⚫When the vehicle height has significantly changed by the load conditions, etc.
⚫When the direction of the sonar sensors is deviated by a collision or other
causes
⚫When the sonar sensors are covere d with rain, snow, ice or dirt
RAIZE_OM_General_BZ358E.book 224 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2264-5. Using the driving support systems
RAIZE_OM_General_BZ358E
WARNING
⦁Moving objects (those appearing sudd enly or traveling across the vehicle)
⦁ Sponge-like items or obstacles with soft surfaces such as snow, which are
likely to absorb sound waves
⦁ When the obstacle’s surface is diagonal to the vehicle
⦁ A wall that is not perpendicular to the ground
⦁ Non-planar walls, such as those with uneven or wavy surface
⦁ Thin obstacles such as wires, wire mesh , ropes, road signs, utility poles and
other poles
⦁ When pillars or pipes are sticking out from the wall
⦁ When an unrecognizable obstacle is located between a recognizable
obstacle and the vehicle
⦁ Obstacles located outside of the sonar’s recognition range
⦁ When the sonar sensor areas are extremely hot under the blazing sun or
extremely cold during winter
⦁ When the sonar sensors are covere d with rain, snow, ice or dirt
⦁ During pouring rain or when water splashes over the vehicle, or strong
wind blowing
⦁ When there is a loud noise around, or there are devices emitting ultra-
sonic waves (the sound of other vehicles’ horns, motorcycle engines, and
air brakes of large vehicles, vehicle detectors, or sonar systems of other
vehicles)
⦁ When commercially availa ble electrical components (such as an internally
illuminated number plate, radio anten na) are installed near the sonar sen-
sors
⦁ When the direction of the sonar sensors is deviated by a collision or other
causes
RAIZE_OM_General_BZ358E.book 226 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2284-5. Using the driving support systems
RAIZE_OM_General_BZ358E✽
: If equipped
Rear-view camera✽
The rear-view camera is a device designed to assist driving when the
vehicle backs up, such as during pa rking, by displaying the vehicle’s
rear-view image on the display audio screen.
The operation may differ depending on the display audio your vehi-
cle has. For details, refer to the included instruction manual.
The screen illustration used in this document is an example. The actual
image displayed will be different from this illustration in terms of how the
vehicle appears. Rear-view camera screen display
When the shift lever is set to R with the engine switch turned “ON”, the dis-
play audio screen shows the vehicle’s rear-view image.
Setting the shift lever to other than R will restore the previous screen.
The rear-view camera image takes prec edence over any other screen dis-
play.
Precautions for the rear-view camera
⬛Screen projection range
KBRO460301
Projection rangeScreen
The screen shows a part of the
vehicle body (such as a bumper).
RAIZE_OM_General_BZ358E.book 228 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2334-5. Using the driving support systems
RAIZE_OM_General_BZ358E
Driving
4
When VSC/TRC is operating
When VSC/TRC is operating, the slip
indicator flashes.
To s t o p T R C
If TRC is activated when escaping from a muddy, sandy, or snowy road, the
engine output may not increase even when the accelerator pedal is
depressed, making it difficult to escape. In such a case, pressing
may make it easier to escape.
Press to stop TRC
The TRC OFF indicator lights.
Press again to return to system
ready state.
⬛To stop VSC and TRC
To stop VSC and TRC, press and hold for 3 seconds or more when the
vehicle has come to a stop.
The TRC OFF indicator and VS C OFF indicator light up.
Press again to return to system ready state.
⬛When the TRC OFF indicator lights up without pressing
The TRC and hill-start assist control ca nnot be activated. Contact your Toyota
dealer.
KBRO460201E
KBRO460202E
RAIZE_OM_General_BZ358E.book 233 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2344-5. Using the driving support systems
RAIZE_OM_General_BZ358E
⬛Activation of ABS/VSC
ABS/VSC does not work at low speeds. The operation is the same as the nor-
mal brake.
⬛Activation sound and vibration of the ABS, brake assist, VSC, TRC, and hill-
start assist control
⚫A sound may be heard from the engine compartment when the brake pedal
is depressed repeatedly, when the engine is started or just after the vehicle
begins to move. This sound does not indicate that a malfunction has
occurred in any of these systems.
⚫Any of the following conditions may occur when the above systems are oper-
ating. None of them indicates that a malfunction has occurred.
⦁ Vibrations may be felt through th e vehicle body and steering wheel
⦁ A motor sound may be heard even after the vehicle has come to a stop
⦁ The brake pedal may pulsate slightly after the ABS is activated
⦁ The brake pedal may move down slightly after the ABS is activated
⬛EPS motor operation sound
When the steering wheel is operated, a motor sound (whirring sound) may be
heard, but this does not indicate a malfunction.
⬛Automatic reactivation of VSC and TRC
After turning the TRC and VSC systems off, the systems will return to the ready
state in the following situations:
⚫When the engine switch is turned to “OFF”
⚫If only the TRC system is turned off, when vehicle speed increases
If both the TRC and VSC systems are tu rned off, automatic reactivation will
not occur when vehicle speed increases.
⬛Reduced effectiveness of the EPS system
The effectiveness of the EPS system is reduced to prevent the system from
overheating when there is frequent steering input over an extended period of
time. The steering wheel ma y feel heavy as a result.
Should this occur, refrain from excessive steering input or stop the vehicle and
turn the engine off. It should re turn to normal within 10 minutes.
RAIZE_OM_General_BZ358E.book 234 ページ ２０２２年５月１７日　火曜日　午後１時５９分

238
RAIZE_OM_General_BZ358E
4-6. Driving tips
Winter driving tips
Carry out the necessary preparations and inspections before driving
the vehicle in winter. Always drive the vehicle in a manner appropri-
ate to the prevailing weather conditions.Preparation for winter
⚫Use fluids that are appropriate to the prevailing outside temperatures.
⦁ Engine oil
⦁ Coolant
⦁ Washer fluid
⚫Have a service technician inspec t the condition of the battery.
Before driving
Perform the following according to the driving conditions:
⚫Do not try to forcibly open a window or move a windshield wiper that is
frozen. Pour warm water over the frozen area to melt the ice. Wipe away
the water immediately to prevent it from freezing.
⚫To ensure proper operation of the air conditioning system fan, remove
any snow that has accumulated on the air inlet vents in front of the
windshield.
⚫Check for and remove any excess ice or snow that may have accumu-
lated on the exterior lights, vehicle’s roof, around the tires or on the
brakes.
⚫Look under the vehicle and check that there are no ice blocks around
the ground. Remove any attached ice blocks with great care to avoid
damaging vehicle components. Also check that the pedals and steering
wheel move smoothly.
⚫Remove any snow or mud from the bottom of your shoes before getting
in the vehicle.
RAIZE_OM_General_BZ358E.book 238 ページ ２０２２年５月１７日　火曜日　午後１時５９分