light TOYOTA RAV4 1996 Service User Guide

BE0JA−01
Z17622
Right
Left
1 2 3
Z07679
2 4
5 1 3
7 96
8 10
BE1843
3
2
1 BE−20
− BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
1996 RAV4 (RM447U)
INSPECTION
1. INSPECT TURN SIGNAL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Left turn1 − 2Continuity
Neutral−No continuity
Right turn2 − 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HAZARD WARNING SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Switch OFF7 − 10Continuity
Switch ON4 − 5 − 6 − 9
7 − 8Continuity
Illumination circuit2 − 3Continuity
If continuity is not as specified, replace the switch.
3. INSPECT TURN SIGNAL FLASHER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative (−) lead to terminal 3.
(b) Connect the 2 turn signal light bulbs parallel to each other
to terminals 1 and 3, check that the bulbs flash.
HINT:
The turn signal lights should flash 60 or 120 times per minute.
If one of the front or rear turn signal lights has an open circuit,
the number of flashing will be more than 140 per minute.
If operation is not as specified, replace the flasher.

BE0JD−05
BE−24
− BODY ELECTRICALBACK−UP LIGHT SYSTEM
1996 RAV4 (RM447U)
BACK−UP LIGHT SYSTEM
LOCATION

BE2682
Push
Free2
1
BE0JE−02
− BODY ELECTRICALBACK−UP LIGHT SYSTEM
BE−25
1996 RAV4 (RM447U)
INSPECTION
1. INSPECT BACK−UP LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Free1 − 2No continuity
Push1 − 2Continuity
If continuity is not as specified, replace the switch.
2. INSPECT PARK/NEUTRAL POSITION SWITCH (See
page DI−156, DI−218)

BE0JF−06
BE−26
− BODY ELECTRICALSTOP LIGHT SYSTEM
1996 RAV4 (RM447U)
STOP LIGHT SYSTEM
LOCATION

BE0JG−01
Z05647
1
2
43
1
4 2
3
− BODY ELECTRICALSTOP LIGHT SYSTEM
BE−27
1996 RAV4 (RM447U)
INSPECTION
INSPECT STOP LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Switch pin free
(Pedal depressed)1 − 2Continuity
Switch pin pushed in
(Pedal released)3 − 4No continuity
If continuity is not as specified, replace the switch.

− BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE−51
1996 RAV4 (RM447U)
Passenger ’s Switch (Window lock):
Switch positionTester connectionSpecified condition
UP7 − 12Continuity
OFF5 − 12Continuity
DOWN5 − 7Continuity
Rear LH side switch (Window lock):
Switch positionTester connectionSpecified condition
UP1 − 9
7 − 10Continuity
OFF1 − 9 − 10Continuity
DOWN1 − 10
7 − 9Continuity
Rear LH side switch (Window lock):
Switch positionTester connectionSpecified condition
UP7 − 10Continuity
OFF9 − 10Continuity
DOWN7 − 9Continuity
Rear RH side switch (Window lock):
Switch positionTester connectionSpecified condition
UP1 − 14
7 − 11Continuity
OFF1 − 11 − 14Continuity
DOWN1 − 11
7 − 14Continuity
Rear RH side switch (Window lock):
Switch positionTester connectionSpecified condition
UP7 − 11Continuity
OFF11 − 14Continuity
DOWN7 − 14Continuity
If continuity is not as specified, replace the switch.
3. 3 Door models:
INSPECT SWITCH ILLUMINATION
Connect the positive (+) lead from the battery to terminal 9, and
the negative (−) lead to terminal 6, and check that all the illu-
minations light up.
If operation is not as specified, replace the master switch.

Z10673
4 3 Wire Harness Side
Z10674
4 3 Wire Harness Side
Z10675
3 BE−52
− BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
1996 RAV4 (RM447U)
4. 5 Door models
INSPECT SWITCH ILLUMINATION
Connect the positive (+) lead from the battery to terminal 7 and
the negative (−) lead to terminal 1 check that all the illuminations
light up.
If operation is not as specified, replace the master switch.
5. 3 Door models:
INSPECT ONE TOUCH POWER WINDOW SYSTEM
(a) Using an ammeter, inspect the system.
(1) Disconnect the connector from the master switch.
(2) Connect the positive (+) lead from the ammeter to
terminal 3 on the wire harness side connector and
the negative (−) lead to the negative (−) terminal of
the battery.
(3) Connect the positive (+) lead from the battery to ter-
minal 4 on the wire harness side connector.
(4) As the window goes down, check that the current
flow is approximately 7 amperes.
(5) Check that the current increases up to approxi-
mately 14.5 amperes or more when the window
stops going down.
HINT:
The circuit breaker opens some 4 − 40 seconds after the win-
dow stops going down, so that check must be made before the
circuit breaker operates.
If the operation is not as specified, replace the master switch.
(b) Using an ammeter with a current measurement probe, in-
spect the system.
(1) Remove the master switch with connector con-
nected.
(2) Attach a current−measuring probe to terminal 3 of
the wire harness.
(3) Turn the ignition switch ON and set the power win-
dow switch in the down position.

V04924
16
AntennaANTENNA−RELATED
Is antenna extended.No
Extend fully.
Ye s
Temporarily install another antenna.
Functions OK?Antenna faulty. Ye s
No
Radio side faulty.
17
NoiseNOISE PRODUCED BY VIBRATION OR SHOCK WHILE
DRIVING
Is speaker properly installed?
Ye sNo
Install properly.
Is each system correctly installed?
Ye sNo
With vehicle stopped, lightly tap each system.
Is noise produced?
NoYe s
Each system faulty.
Noise produced by static electricity accumulating
in the vehicle body.
BE−78
− BODY ELECTRICALAUDIO SYSTEM
1996 RAV4 (RM447U)

BO481−01
N11455
N11456
− BODYFRONT BUMPER
BO−5
1996 RAV4 (RM447U)
REMOVAL
1. REMOVE FRONT FENDER MOULDING
2. REMOVE FENDER LINER
3. REMOVE FRONT BUMPER COVER
Remove the 4 bolts, 3 clips, 2 screws and the bumper cover.
4. REMOVE HEADLIGHT UNDER COVER
5. REMOVE HEADLIGHT
6. REMOVE UPPER REINFORCEMENT
Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
7. REMOVE BUMPER STAY
Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)

H04262: 12 Clips
N11440
− BODYBACK DOOR
BO−23
1996 RAV4 (RM447U)
9. REMOVE DOOR OUTSIDE GARNISH
(a) Remove the 4 plug hole covers.
(b) Insert a screwdriver between the door outside garnish
and back door to remove the door outside garnish.
(c) Disconnect the license plate light connector.
10. REMOVE STOP LIGHT COVER
11. REMOVE UPPER GARNISHES
12. REMOVE UPPER SIDE GARNISHES
13. REMOVE STOP LIGHT