remove transaxle TOYOTA RAV4 1996 Service User Guide

Z18887
A
A
A
B
Q08772
Q08773
A
B AX−18
− AUTOMATIC TRANSAXLE (A241E)AUTOMATIC TRANSAXLE UNIT
1996 RAV4 (RM447U)
20. REMOVE REAR END PLATE
Remove the 4 bolts and rear end plate.
Torque:
A bolt: 9.0 N·m (95 kgf·cm, 78 in.·lbf)
B bolt: 19 N·m (195 kgf·cm, 14 ft·lbf)
21. REMOVE TORQUE CONVERTER CLUTCH MOUNT-
ING BOLT
Turn the crankshaft to gain access and remove the 6 bolts with
holding the crankshaft pulley set bolt by a wrench.
Torque: 27 N·m (280 kgf·cm, 20 ft·lbf)
HINT:
At the time of installation, please refer to the following item.
First install the gray bolt. Then install 5 black bolts while turning
the crankshaft to grain access.
22. SUPPORT TRANSAXLE WITH A TRANSMISSION
JACK
23. REMOVE TRANSAXLE
Remove the rear side transaxle mouting 2 bolts and transaxle.
Torque:
A bolt: 25 N·m (250 kgf·cm, 18 ft·lbf)
B bolt: 46 N·m (470 kgf·cm, 34 ft·lbf)

AX04K−02
− AUTOMATIC TRANSAXLE (A540H)AUTOMATIC TRANSAXLE SYSTEM
AX−1
1996 RAV4 (RM447U)
AUTOMATIC TRANSAXLE SYSTEM
PRECAUTION
When working with FIPG material, you must observe the followings.
Using a razor blade and a gasket scraper, remove all the old FIPG material from the gasket surfaces.
Thoroughly clean all components to remove all the loose material.
Clean both sealing surfaces with a non−residue solvent.
Apply FIPG in an approx. 1 mm (0.04 in.) wide bead along the sealing surface.
Parts must be assembled within 10 minutes of application. Otherwise, the FIPG material must be re-
moved and reapplied.
If the vehicle is equipped with a mobile communication system, refer to the precaution in the IN section.

Q06043
SST
AX04M−02
Q06044
SST
− AUTOMATIC TRANSAXLE (A540H)EXTENSION HOUSING OIL SEAL
AX−3
1996 RAV4 (RM447U)
EXTENSION HOUSING OIL SEAL
ON−VEHICLE REPAIR
1. DRAIN TRANSFER OIL
2. REMOVE PROPELLER SHAFT
(See page PR−3)
3. REMOVE EXTENSION HOUSING OIL SEAL
Using SST, remove the oil seal.
SST 09308−00010
4. INSTALL EXTENSION HOUSING OIL SEAL
(a) Using SST and a hammer, driver in a new oil seal.
SST 09325−20010
Oil seal depth: 1.5 ± 0.4 mm (0.059 ± 0.016 in.)
(b) Coat the lip of the oil seal with MP grease.
5. INSTALL PROPELLER SHAFT
(See page PR−9)
6. FILL TRANSFER WITH OIL
(See page DI−173)

Q08739
AX04N−01
Q06120
Vehicle Speed
SensorO−Ring
Clip Driven Gear
Q08737
Q06119O−Ring
AX−4
− AUTOMATIC TRANSAXLE (A540H)VEHICLE SPEED SENSOR
1996 RAV4 (RM447U)
VEHICLE SPEED SENSOR
ON−VEHICLE REPAIR
1. REMOVE FRONT SPEED SENSOR
(a) Remove the air cleaner assembly.
(b) Disconnect the front speed sensor connector.
(c) Remove the bolt and front speed sensor assembly.
(d) Remove the clip and speedometer driven gear from the
front speed sensor.
(e) Remove the O−ring from the front speed sensor.
2. INSTALL FRONT SPEED SENSOR ASSEMBLY
(a) Coat a new O−ring with ATF and install it to the front
speed sensor.
(b) Install the speedometer driven gear to the front speed
sensor with the clip.
(c) Install the front speed sensor assembly with the bolt.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(d) Connect the front speed sensor connector.
(e) Install the air cleaner assembly.
3. REAR SPEED SENSOR
(a) Remove the air cleaner assembly.
(b) Disconnect the rear speed sensor connector.
(c) Remove the bolt and rear speed sensor.
(d) Remove the O−ring from the rear speed sensor.
4. INSTALL REAR SPEED SENSOR
(a) Coat a new O−ring with ATF and install it to the rear speed
sensor.
(b) Install the rear speed sensor with the bolt.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(c) Connect the rear speed sensor connector.
(d) Install the air cleaner assembly.

Q08865
AX04O−01
− AUTOMATIC TRANSAXLE (A540H)ATF TEMPERATURE SWITCH
AX−5
1996 RAV4 (RM447U)
ATF TEMPERATURE SWITCH
ON−VEHICLE REPAIR
1. REMOVE NO.2 ENGINE UNDER COVER
2. REMOVE ATF TEMPERATURE SWITCH
(a) Disconnect the ATF temperature switch connector.
(b) Remove the ATF temperature switch.
3. INSTALL ATF TEMPERATURE SWITCH
(a) Install the ATF temperature switch.
(b) Connect the ATF temperature switch connector.
4. INSTALL NO.2 ENGINE UNDER COVER

Q08738
AX128−01
Q06066
Q06109
Q06077NRP AX−6
− AUTOMATIC TRANSAXLE (A540H)PARK/NEUTRAL POSITION (PNP) SWITCH
1996 RAV4 (RM447U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON−VEHICLE REPAIR
1. REMOVE NO.2 ENGINE UNDER COVER
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Remove the nut and disconnect the shift control cable.
(b) Remove the nut and shift control lever.
(c) Using a screwdriver, pry off the lock plate.
(d) Remove the nut and lock plate.
(e) Remove the 2 bolts and pull out the park/neutral position
switch.
4. INSTALL AND ADJUST PARK/NEUTRAL POSITION
SWITCH
(a) Install the park/neutral position switch to the manual valve
shaft with the 2 bolts and nut.
(b) Install a new lock plate and tighten the nut.
Torque: 6.9 N·m (70 kgf·cm, 61 in.·lbf)
(c) Stake the nut with the lock plate.
(d) Temporarily install the manual valve lever shaft.
(e) Turn the lever counterclockwise until it stops, then turn it
clockwise 2 notches.
(f) Remove the shaft control lever.

Q06064
AX129−01
AT0103
D00691
D00692
AX−8
− AUTOMATIC TRANSAXLE (A540H)VALVE BODY ASSEMBLY
1996 RAV4 (RM447U)
VALVE BODY ASSEMBLY
ON−VEHICLE REPAIR
1. REMOVE NO.2 ENGINE UNDER COVER
2. DRAIN ATF
Using a 10 mm hexagon wrench, remove the drain plug, and
drain the ATF into a suitable container.
3. REMOVE OIL PAN AND GASKET
(a) Remove the 17 bolts.
(b) Remove the oil pan by lifting transaxle case.
NOTICE:
Some fluid remain in the oil pan.
4. EXHAUST PARTICLES IN PAN
Remove the magnet and use it to collect any steel chips.
Lock carefully at the chips and particles in the oil pan and on the
magnet to anticipate when type of wear you will find in the trans-
axle.
Steel (magnetic): bearing, gear and plate wear
Brass (non−magnetic): bushing wear
5. REMOVE OIL PIPE BRACKET AND STRAINER
(a) Remove the 2 bolts and oil pipe bracket.
(b) Remove the 3 bolts and strainer.
(c) Remove the gasket from the strainer.
6. REMOVE MANUAL VALVE BODY
(a) Remove the 2 bolts and detent spring.

D00693
Q05896
Q05897
D00645
Q05899
− AUTOMATIC TRANSAXLE (A540H)VALVE BODY ASSEMBLY
AX−9
1996 RAV4 (RM447U)
(b) Remove the 5 bolts and manual valve body with the
manual valve.
(c) Remove the manual valve from the manual valve body.
7. REMOVE OIL PIPE
(a) Remove the bolt and retainer.
(b) Pry up both pipe ends with a large screwdriver and re-
move the 8 pipes.
NOTICE:
Be careful not to bend or damage the pipes.
8. DISCONNECT 3 SOLENOID CONNECTORS
9. REMOVE CONNECTOR CLAMP AND PIPE RETAINER
10. REMOVE B
3 APPLY PIPE
Pry up the pipe with a screwdriver and remove the pipe.
NOTICE:
Be careful not to bend or damage the pipes.

D00694
OR0038
Z13387A B CDC
C
D00696
AX−10
− AUTOMATIC TRANSAXLE (A540H)VALVE BODY ASSEMBLY
1996 RAV4 (RM447U)
11. REMOVE VALVE BODY
(a) Remove the 10 bolts.
(b) Disconnect the throttle cable from the cam and remove
the valve body.
12. INSTALL VALVE BODY TO TRANSAXLE CASE
(a) While holding the cam down with your hand, slip the cable
end into the slot.
(b) Raise up the valve body into place.
NOTICE:
Do not entangle the solenoid wire.
(c) Install and tighten the 10 bolts.
Torque: 11 N·m (110 kgf·cm, 8 ft·lbf)
HINT:
Each bolt length is indicated below.
Hand−tighten the 10 bolts first, then torque with a torque
wrench.
Bolt length:
Bolt A: 22 mm (0.87 in.)
Bolt B: 32 mm (1.26 in.)
Bolt C: 43 mm (1.69 in.)
Bolt D: 55 mm (2.17 in.)
13. INSTALL B
3 APPLY PIPE
NOTICE:
Be careful not to bend or damage the pipe.

Q06117
AX04R−02
Q06068
Q057310.8 − 1.5 mm (0.031 − 0.059 in.) 200 mm
(7.87 in.)
− AUTOMATIC TRANSAXLE (A540H)THROTTLE CABLE
AX−13
1996 RAV4 (RM447U)
THROTTLE CABLE
ON−VEHICLE REPAIR
1. DISCONNECT THROTTLE CABLE FROM LINKAGE
2. REMOVE PARK/NEUTRAL POSITION SWITCH
(See page AX−6)
3. REMOVE VALVE BODY
(See page AX−8)
4. REMOVE THROTTLE CABLE
(a) Remove the bolt and pull the cable out of the transaxle
case.
(b) Remove the O−ring from the throttle cable.
5. INSTALL THROTTLE CABLE INTO TRANSAXLE
CASE
If the throttle cable is new do the following operations (a) − (c).
(a) Bend the cable so there is a radius of about 200 mm (7.87
in.).
(b) Pull the inner cable lightly until a slight resistance is felt,
and hold it.
(c) Stake the stopper 0.8 − 1.5 mm (0.031 − 0.059 in.) from
the end of outer cable.
(d) Install a new O−ring to the throttle cable.
(e) Make sure to push it in all the way.
(f) Install and torque the bolt.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
6. INSTALL VALVE BODY
(See page AX−8)
7. CONNECT THROTTLE CABLE TO LINKAGE
8. ADJUST THROTTLE CABLE
(See page DI−173)
9. INSTALL PARK/NEUTRAL POSITION SWITCH
(See page AX−6)
10. TEST DRIVE VEHICLE