engine TOYOTA RAV4 1996 Service Manual PDF

DI−12
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U)
7. ENGINE OPERATING CONDITION
NOTICE:
The value given below for ”Normal Condition” are representative values, so a vehicle may still be
normal even it its value varies from those listed here. So do not decide whether a part is faulty or not
solely according to the ”Normal Condition” here.
(a) CARB Mandated Signals
TOYOTA hand−held tester displayMeasurement ItemNormal Condition *
FUEL SYS #1
Fuel System Bank 1
OPEN: Air−fuel ratio feedback stopped
CLOSED: Air−fuel ratio feedback operating
Idling after warning up: CLOSED
CALC LOAD
Calculator Load:
Current intake air volume as a proportion of max.
intake air volumeIdling: 20.7 − 48.4 %
Racing without load (2,500 rpm) : 17.7 − 45.3 %
COOLANT TEMPEngine Coolant Temperature Sensor ValueAfter warning up: 80 − 95°C (176 − 203°F)
SHORT FT #1Short−term Fuel Trim Bank 10 ± 20 %
LONG FT #1Long−term Fuel Trim Bank 10 ± 20 %
ENGINE SPDEngine SpeedIdling: 700 ± 50 rpm
VEHICLE SPDVehicle SpeedVehicle Stopped: 0 km/h (0 mph)
IGN ADVANCEIgnition Advance
Ignition Timing of Cylinder No.1Idling: BTDC 0 − 10°
INTAKE AIRIntake Air Temperature Sensor ValueEquivalent to Ambient Temp.
MAPAbsolute Pressure Inside Intake ManifoldIdling: 21 − 49 kPa
Racing without load (2,500 rpm): 17 − 46 kPa
THROTTLE POS
Voltage Output of Throttle Position Sensor
Calculated as a Percentage
0V → 0 %, 5V → 100 %Throttle Fully Closed: 6 − 16 %
Throttle Fully Open: 64 − 98 %
O2S B1, S1Voltage Output of Oxygen Sensor
Bnak 1,Sensor 1Idling : 0.1 − 0.9 V
O2FT B1, S1Oxygen Sensor Fuel Trim Bank 1, Sensor 1
(Same as SHORT FT #1)0 ± 20 %
O2S B1, S2Voltage Output of Oxygen Sensor
Bank 1, Sensor 2Driving 50 km/h (31 mph): 0.1 − 0.9 V
*: If no conditions are specifically stated for ”Idling”, it means the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.

− DIAGNOSTICSENGINE
DI−13
1996 RAV4 (RM447U)
(b) TOYOTA Enhanced Signals
TOYOTA hand−held tester displayMeasurement ItemNormal Condition *
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 RPM
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 9 g/r
INJECTORFuel injection time for cylinder No.1Idling: 1.9 − 3.3 ms
IAC DUTY RATIOIntake Air Control Valve Duty Ratio Opening
ratio rotary solenoid type IAC valveIdling: 25 − 60 %
STARTER SIGStarter SignalCranking: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark / Neutral Position Switch SignalP or N position: ON
ELCTRCL LOAD SIGElectrical Load SignalDefogger S/W ON: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1
CYL#2
CYL#3
CYL#4
Abnormal revolution variation for each cylinder0 %
IGNITIONTotal number of ignitions for every 1,000
revolutions0 − 2,000
EGR SYSTEMEGR system operating conditionIdling: OFF
FUEL PUMPFuel Pump SignalIdling: ON
EVAP (PURGE) VSVEVAP VSV SignalVSV operating: ON
VAPOR PRESS VSVVapor Pressure VSV SignalVSV operating: ON
A/C CUT SIGA/C Cut SignalA/C S/W OFF: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 − 1.2
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from lean to rich.
Idling after warned up: 0 − 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from rich to lean.
Idling after warned up: 0 − 1,000 msec.
*: If conditions are specifically stated for ”Idling” , it means the shift lever is at N or P Position, the A/C switch
is OFF and all accessory switches are OFF.

DI3Z8−02
DI−14
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for that code listed
in the table below, for details of each code, turn to the page referred to under the ”See page” for the respec-
tive ”DTC No.” in the DTC chart.
SAE DEFINED
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
P0105
(DI−21)
Manifold Absolute
Pressure / Barometric
Pressure Circuit
MalfunctionOpen or short in Manifold absolute pressure sensor circuit
Manifold absolute pressure sensor
ECM
 *1
P0106
(DI−24)
Manifold Absolute
Pressure / Barometric
Pressure Circuit
Ranger / Performance
Problem
Manifold absolute pressure sensor *1
P0110
(DI−25)Intake Air Temp. Circuit
MalfunctionOpen or short in take air temp. sensor circuit
Intake air temp. sensor
ECM
 *1
P0115
(DI−29)Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM
 *1
P0116
(DI−33)Engine Coolant Temp. Circuit
Range / Performance ProblemEngine coolant temp. sensor
Cooling system *1
P0120
(DI−34)Throttle / Pedal Position
Sensor / Switch ”A” Circuit
MalfunctionOpen or short in throttle position sensor circuit
Throttle position sensor
ECM
 *1
P0121
(DI−38)Throttle / Pedal Position
Sensor / Switch ”A” Circuit
Range / Performance Problem
Throttle position sensor *1
P0125
(DI−39)Insufficient Coolant Temp. for
Closed Loop Fuel ControlOpen or short in oxygen sensor circuit
Oxygen sensor *1
P0130
(DI−42)Oxygen Sensor Circuit Malfunc-
tion
(Bank 1 Sensor 1)Oxygen sensor
Fuel trim malfunction *1
P0133
(DI−45)Oxygen Sensor Circuit Slow
Response
(Bank 1 Sensor 1)
Oxygen sensor *1
P0136
(DI−46)Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Oxygen sensor *1
P0171
(DI−48)System too Lean
(Fuel Trim)
Air Intake (hose loose)
Fuel line pressure
Injector blockage
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor
 *1
*1: MIL lights up

− DIAGNOSTICSENGINE
DI−15
1996 RAV4 (RM447U) DTC No.
(See Page)
Detection ItemTrouble AreaMILMemory
P0172
(DI−48)System too Rich
(Fuel Trim)
Fuel line pressure
Injector blockage, leak
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor
 *1
P0300
(DI−51)Random / Multiple
Cylinder Misfire DetectedIgnition system
Injector
Fuel line pressure
EGR
Compression pressure
Valve clearance not to specification
Valve timing
Manifold absolute pressure sensor
Engine coolant temp. sensor
 *2P0301
P0302
P0303
P0304
(DI−51)Misfire Detected
− Cylinder 1
− Cylinder 2
− Cylinder 3
− Cylinder 4
P0325
(DI−56)Knock Sensor 1 Circuit
MalfunctionOpen or short in knock sensor 1 circuit
Knock sensor 1 (looseness)
ECM
 *1
P0335
(DI−59)Crankshaft Position Sensor
”A” Circuit Malfunction
Open or short in crankshaft position sensor circuit
Crankshaft position sensor
Starter
ECM
 *1
P0336
(DI−62)Camshaft Position Sensor
Circuit Range / PerformanceDistributor
ECM malfunction (for back up) *1
P0340
(DI−63)Camshaft Position Sensor
Circuit Malfunction
Open or short in camshaft position sensor circuit
Camshaft position sensor
Starter
ECM
 *1
P0401
(DI−65)Exhaust Gas Recirculation
Flow Insufficient Detected
EGR valve stuck close
Open or short in VSV circuit for EGR
Vacuum or EGR hose disconnected
Manifold absolute pressure sensor
EGR VSV open or close malfunction
ECM
 *1
P0402
(DI−71)Exhaust Gas Recirculation
Flow Excessive Detected
EGR valve stuck open
Vacuum or EGR hose is connected to wrong post
Manifold absolute pressure sensor
ECM
 *1
P0420
(DI−73)Catalyst System Efficiency
Below ThresholdThree−way catalytic converter
Open or short in oxygen sensor circuit
Oxygen sensor
 *1
P0440
(DI−76)Evaporative Emission Control
System Malfunction
Vapor pressure sensor
Fuel tank cap incorrectly installed
Fuel tank cap cracked or damaged
Vacuum hose cracked, holed, blocked, damaged or
disconnected
Hose or tube cracked, holed, damaged or loose
Fuel tank cracked, holed, or damaged
Charcoal canister cracked, holed or damaged
 *1
*1: MIL lights up
*
2: MIL lights up or blinking

DI−16
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U) DTC No.
(See Page)
Detection ItemTrouble AreaMILMemory
P0441
(DI−82)Evaporative Emission Control
System Incorrect Purge Flow
Open or short in VSV circuit for vapor pressure sensor
VSV for vapor pressure sensor
Open or short in vapor pressure sensor circuit
Vapor pressure sensor
Open or short in VSV circuit for EVAP
VSV for EVAP
Vacuum hose cracked, holed, blocked, damaged or
disconnected
Charcoal canister cracked, holed or damaged
 *1
P0446
(DI−82)Evaporative Emission Control
System Vent Control
Malfunction
P0450
(DI−92)Evaporative Emission Control
System Pressure Sensor
MalfunctionOpen or short in vapor pressure sensor circuit
Vapor pressure sensor
ECM
 *1
P0500
(DI−94)Vehicle Speed Sensor
Malfunction
Open or short in vehicle speed sensor circuit
Vehicle speed sensor
Combination meter
ECM
 *1
P0505
(DI−97)Idle Control System Malfunction
IAC valve is stuck or closed
Open or short in IAC valve circuit
Open or short AC1 single circuit
Air intake (hose loose)
 *1
*1: MIL lights up
MANUFACTURER DEFINED
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
P1300
(DI−100)Ignition Circuit Malfunction
Open or short in IGF or IGT circuit from igniter to ECM
Igniter
ECM
 *1
P1500
(DI−105)Starter Signal Circuit Malfunction
Open or short in starter signal circuit
Open or short in ignition switch or starter relay circuit
ECM
 *1
P1600
(DI−108)ECM BATT MalfunctionOpen in back up power source circuit
ECM *1
P1780
(DI−11 0)Park / Neutral Position Switch
MalfunctionShort in park / neutral position switch circuit
Park / neutral position switch
ECM
 *1
*1: MIL lights up

DI3Z9−02
A15826
− DIAGNOSTICSENGINE
DI−17
1996 RAV4 (RM447U)
PARTS LOCATION

DI3ZA−02
A07400
E4E5E6 DI−18
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U)
TERMINALS OF ECM
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
BATT (E6−1) − E1 (E4−14)R−W ↔ BRAlways9 ∼ 14
+B (E6−12) − E1 (E4−14)B−R ↔ BRIG switch ON9 ∼ 14
VC (E5−1) − E2 (E5−9)Y ↔ BRIG switch ON4.5 ∼ 5.5
VTA (E5−11) − E2 (E5−9)L−R ↔ BR
IG switch ON
Throttle valve fully closed.0.3 ∼ 0.8
IG switch ON
Throttle valve fully open.3.2 ∼ 4.9
PIM (E5−2) − E2 (E5−9)LG−R ↔ BR
IG switch ON3.3 ∼ 3.9
Apply vacuum 26.7 kpa
(200 mmHg, 7.9 in. Hg)2.5 ∼ 3.1
THA (E5−3) − E2 (E5−9)Y−B ↔ BRIdling, Intake air temp. 20°C (68°F)0.5 ∼ 3.4
THW (E5−4) − E2 (E5−9)W ↔ BRIdling, Engine coolant temp. 80°C (176°F)0.2 ∼ 1.0
STA (E6−11) − E1 (E4−14)B−W (M/T) ↔ BRCranking6.0 or more
STA (E6−11) − E1 (E4−14)B (A/T) ↔ BRCranking6.0 or more
#10 (E4−12) − E01 (E4−13)B−R ↔ BR
IG switch ON9 ∼ 14
IdlingPulse generation
(See page DI−51)
#20 (E4−11) − E01 (E4−13)B−Y ↔ BR
IG switch ON9 ∼ 14
IdlingPulse generation
(See page DI−51)
#30 (E4−25) − E01 (E4−13)B−R ↔ BR
IG switch ON9 ∼ 14
IdlingPulse generation
(See page DI−51)
#40 (E4−24) − E01 (E4−13)B−Y ↔ BR
IG switch ON9 ∼ 14
IdlingPulse generation
(See page DI−51)
IGT (E4−20) − E1 (E4−14)B ↔ BRIdlingPulse generation
(See page DI−100)
IGF (E4−3) − E1 (E4−14)L−Y ↔ BR
IG switch ON
Disconnect igniter connector4.5 ∼ 5.5
IdlingPulse generation
(See page DI−100)
G (E4−5) − NE (E4−14)B ↔ GIdlingPulse generation
(See page DI−59)
NE (E4−4) − NE (E4−17)R ↔ GIdlingPulse generation
(See page DI−59)

− DIAGNOSTICSENGINE
DI−19
1996 RAV4 (RM447U) FC (E6−14) − E1 (E4−14)
G−R ↔ BRIG switch ON9 ∼ 14
EGR (E4−23) − E1 (E4−14)B−W ↔ BRIG switch ON0 ∼ 3
ISCC (E4−9) − E1 (E4−14)B−Y ↔ BRIG switch ON
Disconnect E4 of ECM connector9 ∼ 14
ISCO (E4−10) − E1 (E4−14)B−L ↔ BRIG switch ON
Disconnect E4 of ECM connector9 ∼ 14
OX1 (E5−6) − E1 (E4−14)B ↔ BRMaintain engine speed at 2,500 rpm for 2 mins. after
warning up.Pulse generation
OX2 (E5−5) − E1 (E4−14)B ↔ BRMaintain engine speed at 2,500 rpm for 2 mins. after
warning up.Pulse generation
KNK (E5−10) − E1 (E4−14)B ↔ BRIdlingPulse generation
(See page DI−56)
* NSW (E6−22) − E1 (E4−14)B−W ↔ BR
IG switch ON
Other shift position in ”P” , ”N” position9 ∼ 14
IG switch ON
Shift position in ”P” , ”N” position0 ∼ 3.0
SPD (E6−9) − E1 (E4−14)V−W ↔ BRIG switch ON
Rotate driver wheel slowly.Pulse generation
(See page DI−94)
TE1 (E5−15) − E1 (E4−14)L−W ↔ BRIG switch ON9 ∼ 14
W (E6−5) − E1 (E4−14)G−R ↔ BRIdling9 ∼ 14
IG switch ONBelow 3.0
AC (E6−10) − E1 (E4−14)Y−G ↔ BRIdling, A/C switch ONBelow 2.0
Idling, A/C switch OFF9 ∼ 14
ACT (E6−21) − E1 (E4−14)R−Y ↔ BRIdling, A/C switch ON9 ∼ 14
Idling, A/C switch OFFBelow 2.0
* OD2 (E6−7) − E1 (E4−14)LG ↔ BRIG switch ON, O/D main switch pushed out9 ∼ 14
IG switch ON, O/D main switch pushed in0 ∼ 3
* OD1 (E6−20) − E1 (E4−14)Y−B ↔ BRIG switch ON, Cruise control ECU no request O/D cut9 ∼ 14
IG switch ON, Cruise control ECU request O/D cut0 ∼ 3
EVP (E4−22) − E1 (E4−14)P ↔ BRIG switch ON9 ∼ 14
TPC (E5−8) − E1 (E4−14)R−W ↔ BRIG switch ON9 ∼ 14
PTNK (E5−7) − E2 (E5−9)L−Y ↔ BR
IG switch ON, Disconnect vacuum hose from vapor
pressure sensor2.9 ∼ 3.7
Apply vacuum
(4.0 kPa, 30 mmHg, 1.18 in. Hg)
(less than 66.7 kPa, 500 mmHg, 19.7 in. Hg)
Below 0.5
ELS (E6−17) − E1 (E4−14)B ↔ BRDefogger switch and taillight switch ON7.5 ∼ 14
Defogger switch and taillight switch OFF0 ∼ 1.5
SDL (E6−16) − E1 (E4−14)W ↔ BRDuring transmissionPules generation
*: A/T only

DI3ZB−02
DI−20
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U)
PROBLEM SYMPTOMS TABLE
When the malfunction code is not confirmed the DTC check and the problem still can not be confirmed in
the basic inspection, then proceed to this step and perform troubleshooting according to the numbered order
given in the table below.
SymptomSuspect AreaSee page
Does not start (Engine does not crank1. Starter and starter relayST Section
Does not start (No combustion)
1. ECM power source circuit
2. Fuel pump control circuit
3. Engine control module (ECM)DI−11 3
DI−11 6
IN−30
Does not start (No complete combustion)1. Fuel pump control circuitDI−11 6
Difficult to start (Engine cranks normally)1. Fuel pump control circuit
2. CompressionDI−11 6
EM−3
Difficult to start (Cold engine)1. Starter signal circuit
2. Fuel pump control circuitDI−105
DI−11 6
Difficult to start (Hot engine)1. Starter signal circuit
2. Fuel pump control circuitDI−105
DI−11 6
Poor idling (High engine idle speed)1. A/C signal circuit
2. ECM power source circuitAC−64
DI−11 3
Poor idling (Low engine idle speed)1. A/C signal circuit
2. Fuel pump control circuitAC−64
DI−11 6
Poor idling (Rough idling)1. Compression
2. Fuel pump control circuitEM−3
DI−11 6
Poor idling (Hunting)1. ECM power source circuit
2. Fuel pump control circuitDI−11 3
DI−11 6
Poor Driveability (Hesitation / Poor acceleration)
1. Fuel pump control circuit
2. A/T faulty
3. A/C cut control circuitDI−11 6
DI−141
DI−122
Poor Driveability (Surging)1. Fuel pump control circuitDI−11 6
Engine stall (Soon after starting)1. Fuel pump control circuitDI−11 6
Engine stall (During A/C operation)1. A/C signal circuit
2. Engine control module (ECM)AC−64
IN−30

DI3ZC−01
P01242
(V)
(3.96)
3.6
2.4
1.2
150 450 750 (840)mmHg
20
60
100(112)
Manifold Absolute PressurekPa
Output Voltage
− DIAGNOSTICSENGINE
DI−21
1996 RAV4 (RM447U)
CIRCUIT INSPECTION
DTC P0105 Manifold Absolute Pressure / Barometric
Pressure Circuit Malfunction
CIRCUIT DESCRIPTION
By a built−in sensor unit, the manifold absolute pressure sensor
detects the intake manifold pressure as a voltage. The ECM
then determines the basic injection duration and basic injection
advance angle based on this voltage. Since the manifold abso-
lute pressure sensor does not use the atmospheric pressure as
a criterion, but senses the absolute pressure inside the intake
manifold (the pressure in proportion to the present absolute
vacuum 0) , it is not influenced by fluctuations in the atmospher-
ic pressure due to high altitude and other factors. This permits
it to control the air−fuel ratio at the proper lever under all condi-
tions.
DTC No.DTC Detecting ConditionTrouble Area
P0105Open or short manifold absolute pressure sensor circuit
Open or short in manifold absolute pressure sensor circuit
Manifold absolute pressure sensor
ECM
If the ECM detects DTC ”P0105” it operates the fail safe function, keeping the ignition timing and injection
volume constant and making it possible to drive the vehicle.
HINT:
After confirming DTC P0105 use the OBDII scan tool or TOYOTA hand−held tester to confirm the manifold
absolute pressure from ”CURRENT DATA”.
Manifold Absolute PressureMalfunction
0 kpaPIM circuit short
130 kpa or more
VC circuit open or short
PIM circuit open
E2 circuit open