remove transaxle TOYOTA RAV4 1996 Service Manual PDF

Q06190
Q01615
Q00056
Q05815
FIPG
MT0669
− MANUAL TRANSAXLEMANUAL TRANSAXLE ASSEMBLY
MX−19
1996 RAV4 (RM447U)
18. REMOVE SNAP RING
(a) Using a snap ring expander, remove the input shaft rear
bearing snap ring.
(b) Using 2 screwdrivers and a hammer, remove the 2 snap
rings.
19. REMOVE STRAIGHT SCREW PLUG, SEAT, SPRING
AND LOCKING BALL
(a) Using a hexagon wrench (6 mm), remove the plug.
Sealant:
Part No. 08833−00080, THREE BOND 1344, LOCTITE
242 or equivalent
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Using a magnetic finger, remove the seat, spring and
locking ball.
20. REMOVE REVERSE IDLER GEAR SHAFT LOCK BOLT
Sealant:
Part No. 08833−00080, THREE BOND 1344, LOCTITE
242 or equivalent
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
21. REMOVE TRANSMISSION CASE
Remove the 17 bolts and tap the case with a plastic hammer.
FIPG:
Part No. 08826−00090, THREE BOND 1281 or equiva-
lent
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
22. REMOVE SHIM
HINT:
At the time of reassembly, please refer to the following item.
Install the previously selected shim by adjusting output shaft
preload.
(See page MX−27)

MT0693
SST
Q06375
Z17557
Matchmarks
Q01614
Q08124
MX−20
− MANUAL TRANSAXLEMANUAL TRANSAXLE ASSEMBLY
1996 RAV4 (RM447U)
23. REMOVE OUTPUT SHAFT REAR TAPER ROLLER
BEARING OUTER RACE
Using SST and a hammer, remove the output shaft rear taper
roller bearing outer race.
SST 09316−60011 (09316−00011)
24. REMOVE TRANSMISSION OIL PIPE
(a) Remove the gasket from the oil pipe.
(b) Remove the 2 bolts and oil pipe.
Torque: 17 N·m (175 kgf·cm, 13 ft·lbf)
25. REMOVE REVERSE SHIFT ARM BRACKET AS-
SEMBLY
Remove the bolt and pull off the reverse shift arm and bracket.
Torque: 17 N·m (175 kgf·cm, 13 ft·lbf)
26. REMOVE REVERSE IDLER GEAR AND SHAFT
Pull out the shaft, remove the reverse idler gear and thrust
washer.
HINT:
At the time of reassembly, please refer to the following item.
Align the matchmarks, as shown.
27. REMOVE STRAIGHT SCREW PLUG, LOCKING BALL
AND SPRING
(a) Using a hexagon wrench (6 mm), remove the 2 plugs.
Sealant:
Part No. 08833−00080, THREE BOND 1344, LOCTITE
242 or equivalent
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Using a magnetic finger, remove the 2 seats, springs and
balls.
28. REMOVE NO.1, NO.2 SHIFT FORKS AND SHIFT HEAD
SET BOLT
Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
29. REMOVE NO.1 SHIFT FORK SHAFT
Pull up the No.3 shift fork shaft, remove the No.1 shift fork shaft.
HINT:
At the time of reassembly, please refer to the following item.
When it is difficult to push the fork shaft through the reverse shift
fork, pull up the No.3 shift fork shaft.

Q08125
Q08126
Z00182
− MANUAL TRANSAXLEMANUAL TRANSAXLE ASSEMBLY
MX−21
1996 RAV4 (RM447U)
30. REMOVE INTERLOCK ROLLER
Using a magnetic finger, remove the interlock roller from the re-
verse shift fork.
31. REMOVE NO.2 SHIFT FORK SHAFT, SHIFT HEAD
AND NO.1 SHIFT FORK
(a) Pull out the No.2 shift fork shaft.
(b) Remove the shift head and No.1 shift fork.
32. REMOVE NO.3 SHIFT FORK SHAFT WITH REVERSE
SHIFT FORK AND NO.2 SHIFT FORK
(a) Pull out the No.3 shift fork shaft with the reverse shift fork.
(b) Remove the No.2 shift fork.
33. REMOVE SNAP RING
(a) Using 2 screwdrivers and a hammer, remove the snap
ring and reverse shift fork from the No.3 shift fork shaft.
(b) Using 2 screwdrivers and a hammer, remove the 3 snap
rings from the No.1, No.2 and No.3 shift fork shafts.
34. REMOVE INPUT AND OUTPUT SHAFTS ASSEMBLY
(a) Leaning the output shaft to the differential side, remove
the input shaft assembly.
(b) Lift up the differential case assembly, remove the output
shaft assembly.
35. REMOVE DIFFERENTIAL CASE ASSEMBLY
(a) Remove the oil pump drive gear.
(b) Remove the differential case assembly.
36. REMOVE MAGNET FROM TRANSAXLE CASE
37. REMOVE TRANSMISSION OIL PUMP ASSEMBLY
AND OIL PIPE
(a) Remove the 2 bolts and oil pipe.
Torque: 17 N·m (175 kgf·cm, 13 ft·lbf)
(b) Remove the 2 bolts and oil pump assembly.
Torque: 17 N·m (175 kgf·cm, 13 ft·lbf)

MT0781
MX−22
− MANUAL TRANSAXLEMANUAL TRANSAXLE ASSEMBLY
1996 RAV4 (RM447U)
38. REMOVE NO.5 SYNCHRONIZER RING WITH KEY
SPRING FROM NO.3 CLUTCH HUB
(a) Remove the No.5 synchronizer ring with the key spring
from the No.3 clutch hub.
(b) Using a screwdriver, remove the snap ring.
HINT:
Wrap vinyl tape on the screwdriver to prevent damaging the
synchronizer ring.
(c) Remove the synchronizer rings.

Z00192
SST
MX0DU−01
Z00194
SST
Q08014
SST
Q05164
SST
Q00141
SST MX−24
− MANUAL TRANSAXLEMANUAL TRANSAXLE ASSEMBLY
1996 RAV4 (RM447U)
REPLACEMENT
1. REPLACE INPUT SHAFT BEARING AND OIL SEAL
(a) Remove the 3 bolts and transaxle case receiver.
(b) Using SST, pull out the bearing.
SST 09612−65014
(c) Using a screwdriver, remove the oil seal.
(d) Using SST, drive in a new oil seal.
SST 09608−00081, 09950−70010 (09951−07150)
(e) Coat the lip of seal with MP grease.
(f) Using SST, drive in a new bearing.
SST 09950−60010 (09951−00580), 09950−70010
(09951−07150)
(g) Install the transaxle case receiver.
(h) Install and torque the 3 bolts.
Torque: 7.4 N·m (75 kgf·cm, 65 in.·lbf)
(i) Using SST and a press, remove the inner race.
SST 09950−00020
(j) Using SST and a press, install a new input shaft front
bearing inner race.
SST 09316−60011 (09316−00021)

Q00338
SST
Z00197
Q06368
SST
SST
Q00245
SSTSocket Wrench
Z00199SST
− MANUAL TRANSAXLEMANUAL TRANSAXLE ASSEMBLY
MX−25
1996 RAV4 (RM447U)
2. REPLACE OUTPUT SHAFT FRONT BEARING OUTER
RACE AND OUTPUT SHAFT FRONT COVER
(a) Using SST, pull out the output shaft front bearing outer
race.
SST 09308−00010
(b) Remove the output shaft cover.
(c) Install a new output shaft cover.
HINT:
Install the output shaft cover projection into the case side
groove.
(d) Using SST and a hammer, drive in a new output shaft front
bearing outer race.
SST 09316−60011 (09316−00011, 09316−00021)
(e) Using SST and a socket wrench, remove the output shaft
front bearing.
SST 09950−00020, 09950−00030
(f) Using SST and a press, install a new output shaft front
bearing.
SST 09316−60011 (09316−00071)

Q01611
Z00201
MX−26
− MANUAL TRANSAXLEMANUAL TRANSAXLE ASSEMBLY
1996 RAV4 (RM447U)
3. REPLACE REVERSE RESTRICT PIN
(a) Using a hexagon wrench (6 mm), remove the screw plug.
(b) Using a pin punch and hammer, drive out the slotted
spring pin.
(c) Replace the reverse restrict pin.
(d) Using a pin punch and hammer, drive in the slotted spring
pin.
(e) Apply sealant to the screw plug threads.
Sealant:
Part No. 08833−00080, THREE BOND 1344, LOCTITE
242 or equivalent
(f) Using a hexagon wrench (6 mm), install and torque the
screw plug.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)

MX05X−01
− MANUAL TRANSAXLEMANUAL TRANSAXLE ASSEMBLY
MX−27
1996 RAV4 (RM447U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See
page MX−16).
NOTICE:
When working with FIPG material, you must observe the follow-
ing items.
Using a razor blade and gasket scraper, remove all the old
FIPG material from the gasket surfaces.
Thoroughly clean all components to remove all the loose
material.
Clean both sealing surfaces with a non−residue solvent.
Apply FIPG in an approx. 1 mm (0.04 in.) wide bead along
the sealing surface.
Parts must be assembled within 10 minutes of application.
Otherwise, the FIPG material must be removed and reap-
plied.
HINT:
Before reassembly, select a shim by adjusting output
shaft preload.
Coat all of the sliding and rotating surfaces with gear oil
before reassembly.
ADJUST OUTPUT SHAFT PRELOAD
(a) Install the output shaft assembly to the transaxle case.
(b) Install the transmission case to the transaxle case.
HINT:
If necessary, tap on the case with a plastic hammer.
(c) Install and torque the 17 bolts.
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
(d) Install the output shaft rear taper roller bearing outer race.
(e) Install the adjusting shim.
HINT:
When reusing the output shaft bearing, first install a shim of the
same thickness as before. If installing a new taper roller bear-
ing, first select and install a shim of lesser thickness than be-
fore.
(f) Install the rear bearing retainer.
(g) Using a torx wrench (T45), install and torque the 7 torx
screws.
Torque: 42 N·m (430 kgf·cm, 31 ft·lbf)
(h) Install a new lock nut to the output shaft.
(i) Turn the output shaft right and left 2 or 3 times to allow the
bearing to settle.

Z12593
MX−28
− MANUAL TRANSAXLEMANUAL TRANSAXLE ASSEMBLY
1996 RAV4 (RM447U)
(j) Using a torque wrench, measure the preload.
Preload (at starting):
New bearing
0.8−1.6 N·m (8−16 kgf·cm, 6.9−13.9 in.·lbf)
Reused bearing
0.5−1.0 N·m (5−10 kgf·cm, 4.3−8.7 in.·lbf)
If the preload is not within the specification, select an appropri-
ate adjusting shim.
(k) The preload will change about 0.4−0.5 N·m (4−5 kgf·cm,
3.5−4.3 in.·lbf) for every 0.05 mm change in adjusting
shim thickness.
MarkThickness mm (in.)MarkThickness mm (in.)
01.30 (0.0512)D1.95 (0.0768)
11.35 (0.0531)E2.00 (0.0787)
21.40 (0.0551)F2.05 (0.0807)
31.45 (0.0571)G2.10 (0.0827)
41.50 (0.0591)H2.15 (0.0846)
51.55 (0.0610)J2.20 (0.0866)
61.60 (0.0630)K2.25 (0.0886)
71.65 (0.0650)L2.30 (0.0906)
81.70 (0.0669)M2.35 (0.0925)
91.75 (0.0689)N2.40 (0.0945)
A1.80 (0.0709)P2.45 (0.0965)
B1.85 (0.0728)Q2.50 (0.0984)
C1.90 (0.0748)−−
(l) Remove the lock nut.
(m) Remove these parts. Removal is in the reverse order of
installation.
Rear bearing retainer
Shim
Transmission case
Output shaft assembly
Output shaft rear bearing outer race

MX029−02
Q06369
3rd Gear
4th Gear
Q00111
Q05165
SST MX−30
− MANUAL TRANSAXLEINPUT SHAFT
1996 RAV4 (RM447U)
DISASSEMBLY
1. MEASURE 3RD AND 4TH GEARS THRUST CLEAR-
ANCE
Using a feeler gauge, measure the thrust clearance.
Standard clearance:
3rd gear: 0.10 − 0.35 mm (0.0039 − 0.0138 in.)
4th gear: 0.10 − 0.55 mm (0.0039 − 0.0217 in.)
Maximum clearance:
3rd gear: 0.40 mm (0.0157 in.)
4th gear: 0.60 mm (0.0236 in.)
2. CHECK 3RD AND 4TH GEARS RADIAL CLEARANCE
Using a dial indicator, measure the radial clearance between
the gear and shaft.
Standard clearance:
3rd gear: 0.009 − 0.053 mm (0.0004 − 0.0021 in.)
4th gear: 0.009 − 0.051 mm (0.0004 − 0.0020 in.)
Maximum clearance:
3rd and 4th gears: 0.070 mm (0.0028 in.)
If the clearance exceeds the maximum, replace the gear,
needle roller bearing or shaft.
3. REMOVE SNAP RING
Using 2 screwdrivers and a hammer, tap out the snap ring.
4. REMOVE REAR BALL BEARING AND 4TH GEAR
Using SST and a press, remove the rear bearing.
SST 09950−00020
5. REMOVE NEEDLE ROLLER BEARING, SPACER AND
SYNCHRONIZER RING
6. REMOVE SNAP RING
Using 2 screwdrivers and a hammer, tap out the snap ring.