Vacuum hose TOYOTA RAV4 1996 Service Repair Manual

BR02S−02
R10718
BR−18
− BRAKEBRAKE BOOSTER ASSEMBLY
1996 RAV4 (RM447U)
REMOVAL
1. REMOVE MASTER CYLINDER (See page BR−9)
2. REMOVE CHARCOAL CANISTER
3. DISCONNECT VACUUM HOSE FROM BRAKE
BOOSTER
4. REMOVE PEDAL RETURN SPRING
5. REMOVE CLIP AND CLEVIS PIN
6. REMOVE BRAKE BOOSTER
(a) Remove the 4 nuts and clevis.
(b) Pull out the brake booster and gasket.

BR0M3−01
F03521
SST
Gasket
N00744
SST
− BRAKEBRAKE BOOSTER ASSEMBLY
BR−19
1996 RAV4 (RM447U)
INSTALLATION
1. INSTALL BRAKE BOOSTER
(a) Install the booster and a new gasket.
(b) Install the clevis to the operating rod.
(c) Install and torque the booster installation nuts.
Torque:
13 N·m (130 kgf·cm, 9 ft·lbf)
(d) Insert the clevis pin into clevis, brake pedal, and install the
clip to the clevis pin.
(e) Install the pedal return spring.
2. ADJUST LENGTH OF BOOSTER PUSH ROD
(a) Install a new gasket on the master cylinder.
(b) Set the SST on the gasket, and lower the pin until its tip
slightly touches the piston.
SST 09737−00010
(c) Turn the SST upside down, and set it on the booster.
SST 09737−00010
(d) Measure the clearance between the booster push rod
and pin head (SST).
Clearance: 0 mm (0 in.)
(e) Adjust the booster push rod length until the push rod
slightly touches the pin head.
3. INSTALL CHARCOAL CANISTER TO ORIGINAL POSI-
TION
4. INSTALL MASTER CYLINDER
5. CONNECT VACUUM HOSE TO BRAKE BOOSTER
6. FILL BRAKE RESERVOIR WITH BRAKE FLUID AND
BLEED BRAKE SYSTEM (See page BR−4)
7. M/T:
BLEED CLUTCH SYSTEM
8. CHECK FOR LEAKS
9. CHECK AND ADJUST BRAKE PEDAL
(See page BR−6)
Check and adjust the brake pedal, then tighten the clevis lock
nut.
Torque:
25 N·m (260 kgf·cm, 19 ft·lbf)
10. DO OPERATIONAL CHECK (See page BR−16)

CO0BO−02
Z00570
Radiator Cap Tester
Radiator Cap30° or More
S01265
Radiator Cap Tester CO−14
− COOLINGRADIATOR
1996 RAV4 (RM447U)
ON−VEHICLE INSPECTION
1. REMOVE RADIATOR CAP
CAUTION:
To avoid the danger of being burned, do not remove the ra-
diator cap while the engine and radiator are still hot, as fluid
and steam can be blown out under pressure.
2. INSPECT RADIATOR CAP
NOTICE:
If the radiator cap has contaminations, always rinse
it with water.
When performing steps (a) and (b) below, keep the ra-
diator cap tester at an angle of over 30°above the hor-
izontal.
(a) Using a radiator cap tester, slowly pump the tester and
check that air is coming from the vacuum valve.
Pump speed:
1 push/(3 seconds or more)
NOTICE:
Push the pump at a constant speed.
If air is not coming from the vacuum valve, replace the radiator
cap.
(b) Pump the tester and measure the relief valve opening
pressure.
Pump speed:
1 push within 1 second
NOTICE:
This pump speed is for the first pump only (in order to close
the vacuum valve). After this, the pump speed can be re-
duced.
Standard opening pressure:
74 − 103 kPa (0.75 − 1.05 kgf/cm
2, 10.7 − 14.9 psi)
Minimum opening pressure:
59 kPa (0.6 kgf/cm
2, 8.5 psi)
HINT:
Use the tester’s maximum reading as the opening pressure.
If the opening pressure is less than minimum, replace the radia-
tor cap.
3. INSPECT COOLING SYSTEM FOR LEAKS
(a) Fill the radiator with coolant and attach a radiator cap tes-
ter.
(b) Warm up the engine.
(c) Pump it to 118kPa (1.2 kgf/cm
2, 17.1 psi), and check that
the pressure does not drop.
If the pressure drops, check the hoses, radiator or water pump
for leaks. If no external leaks are found, check the heater core,
cylinder block and cylinder head.
4. REINSTALL RADIATOR CAP

− DIAGNOSTICSENGINE
DI−15
1996 RAV4 (RM447U) DTC No.
(See Page)
Detection ItemTrouble AreaMILMemory
P0172
(DI−48)System too Rich
(Fuel Trim)
Fuel line pressure
Injector blockage, leak
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor
 *1
P0300
(DI−51)Random / Multiple
Cylinder Misfire DetectedIgnition system
Injector
Fuel line pressure
EGR
Compression pressure
Valve clearance not to specification
Valve timing
Manifold absolute pressure sensor
Engine coolant temp. sensor
 *2P0301
P0302
P0303
P0304
(DI−51)Misfire Detected
− Cylinder 1
− Cylinder 2
− Cylinder 3
− Cylinder 4
P0325
(DI−56)Knock Sensor 1 Circuit
MalfunctionOpen or short in knock sensor 1 circuit
Knock sensor 1 (looseness)
ECM
 *1
P0335
(DI−59)Crankshaft Position Sensor
”A” Circuit Malfunction
Open or short in crankshaft position sensor circuit
Crankshaft position sensor
Starter
ECM
 *1
P0336
(DI−62)Camshaft Position Sensor
Circuit Range / PerformanceDistributor
ECM malfunction (for back up) *1
P0340
(DI−63)Camshaft Position Sensor
Circuit Malfunction
Open or short in camshaft position sensor circuit
Camshaft position sensor
Starter
ECM
 *1
P0401
(DI−65)Exhaust Gas Recirculation
Flow Insufficient Detected
EGR valve stuck close
Open or short in VSV circuit for EGR
Vacuum or EGR hose disconnected
Manifold absolute pressure sensor
EGR VSV open or close malfunction
ECM
 *1
P0402
(DI−71)Exhaust Gas Recirculation
Flow Excessive Detected
EGR valve stuck open
Vacuum or EGR hose is connected to wrong post
Manifold absolute pressure sensor
ECM
 *1
P0420
(DI−73)Catalyst System Efficiency
Below ThresholdThree−way catalytic converter
Open or short in oxygen sensor circuit
Oxygen sensor
 *1
P0440
(DI−76)Evaporative Emission Control
System Malfunction
Vapor pressure sensor
Fuel tank cap incorrectly installed
Fuel tank cap cracked or damaged
Vacuum hose cracked, holed, blocked, damaged or
disconnected
Hose or tube cracked, holed, damaged or loose
Fuel tank cracked, holed, or damaged
Charcoal canister cracked, holed or damaged
 *1
*1: MIL lights up
*
2: MIL lights up or blinking

DI−16
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U) DTC No.
(See Page)
Detection ItemTrouble AreaMILMemory
P0441
(DI−82)Evaporative Emission Control
System Incorrect Purge Flow
Open or short in VSV circuit for vapor pressure sensor
VSV for vapor pressure sensor
Open or short in vapor pressure sensor circuit
Vapor pressure sensor
Open or short in VSV circuit for EVAP
VSV for EVAP
Vacuum hose cracked, holed, blocked, damaged or
disconnected
Charcoal canister cracked, holed or damaged
 *1
P0446
(DI−82)Evaporative Emission Control
System Vent Control
Malfunction
P0450
(DI−92)Evaporative Emission Control
System Pressure Sensor
MalfunctionOpen or short in vapor pressure sensor circuit
Vapor pressure sensor
ECM
 *1
P0500
(DI−94)Vehicle Speed Sensor
Malfunction
Open or short in vehicle speed sensor circuit
Vehicle speed sensor
Combination meter
ECM
 *1
P0505
(DI−97)Idle Control System Malfunction
IAC valve is stuck or closed
Open or short in IAC valve circuit
Open or short AC1 single circuit
Air intake (hose loose)
 *1
*1: MIL lights up
MANUFACTURER DEFINED
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
P1300
(DI−100)Ignition Circuit Malfunction
Open or short in IGF or IGT circuit from igniter to ECM
Igniter
ECM
 *1
P1500
(DI−105)Starter Signal Circuit Malfunction
Open or short in starter signal circuit
Open or short in ignition switch or starter relay circuit
ECM
 *1
P1600
(DI−108)ECM BATT MalfunctionOpen in back up power source circuit
ECM *1
P1780
(DI−11 0)Park / Neutral Position Switch
MalfunctionShort in park / neutral position switch circuit
Park / neutral position switch
ECM
 *1
*1: MIL lights up

− DIAGNOSTICSENGINE
DI−19
1996 RAV4 (RM447U) FC (E6−14) − E1 (E4−14)
G−R ↔ BRIG switch ON9 ∼ 14
EGR (E4−23) − E1 (E4−14)B−W ↔ BRIG switch ON0 ∼ 3
ISCC (E4−9) − E1 (E4−14)B−Y ↔ BRIG switch ON
Disconnect E4 of ECM connector9 ∼ 14
ISCO (E4−10) − E1 (E4−14)B−L ↔ BRIG switch ON
Disconnect E4 of ECM connector9 ∼ 14
OX1 (E5−6) − E1 (E4−14)B ↔ BRMaintain engine speed at 2,500 rpm for 2 mins. after
warning up.Pulse generation
OX2 (E5−5) − E1 (E4−14)B ↔ BRMaintain engine speed at 2,500 rpm for 2 mins. after
warning up.Pulse generation
KNK (E5−10) − E1 (E4−14)B ↔ BRIdlingPulse generation
(See page DI−56)
* NSW (E6−22) − E1 (E4−14)B−W ↔ BR
IG switch ON
Other shift position in ”P” , ”N” position9 ∼ 14
IG switch ON
Shift position in ”P” , ”N” position0 ∼ 3.0
SPD (E6−9) − E1 (E4−14)V−W ↔ BRIG switch ON
Rotate driver wheel slowly.Pulse generation
(See page DI−94)
TE1 (E5−15) − E1 (E4−14)L−W ↔ BRIG switch ON9 ∼ 14
W (E6−5) − E1 (E4−14)G−R ↔ BRIdling9 ∼ 14
IG switch ONBelow 3.0
AC (E6−10) − E1 (E4−14)Y−G ↔ BRIdling, A/C switch ONBelow 2.0
Idling, A/C switch OFF9 ∼ 14
ACT (E6−21) − E1 (E4−14)R−Y ↔ BRIdling, A/C switch ON9 ∼ 14
Idling, A/C switch OFFBelow 2.0
* OD2 (E6−7) − E1 (E4−14)LG ↔ BRIG switch ON, O/D main switch pushed out9 ∼ 14
IG switch ON, O/D main switch pushed in0 ∼ 3
* OD1 (E6−20) − E1 (E4−14)Y−B ↔ BRIG switch ON, Cruise control ECU no request O/D cut9 ∼ 14
IG switch ON, Cruise control ECU request O/D cut0 ∼ 3
EVP (E4−22) − E1 (E4−14)P ↔ BRIG switch ON9 ∼ 14
TPC (E5−8) − E1 (E4−14)R−W ↔ BRIG switch ON9 ∼ 14
PTNK (E5−7) − E2 (E5−9)L−Y ↔ BR
IG switch ON, Disconnect vacuum hose from vapor
pressure sensor2.9 ∼ 3.7
Apply vacuum
(4.0 kPa, 30 mmHg, 1.18 in. Hg)
(less than 66.7 kPa, 500 mmHg, 19.7 in. Hg)
Below 0.5
ELS (E6−17) − E1 (E4−14)B ↔ BRDefogger switch and taillight switch ON7.5 ∼ 14
Defogger switch and taillight switch OFF0 ∼ 1.5
SDL (E6−16) − E1 (E4−14)W ↔ BRDuring transmissionPules generation
*: A/T only

P25430
Throttle Body
Exhaust GasEGR Valve
Diagram ECM
VSV
Throttle
Valve
Intake Air
Chamber
EGR
Vacuum
Modulator
S02387
From
Battery6
1J2
1
1E J/B No.1EFI Main Relay
Fuse Block
11
10E423
EA12 R/B No.6ECM
J1
Junction Connector
AA
W−B B−W VSV (for EGR)
2
1
B−O
IGNEGR
E01
EAFrom
IG Switch
B−O 666 3
125
R−W
B−RB−R
W−B
− DIAGNOSTICSENGINE
DI−65
1996 RAV4 (RM447U)
DTC P0401 Exhaust Gas Recirculation Flow Insufficient
Detected
CIRCUIT DESCRIPTION
The EGR system recirculates exhaust gas, which is controlled to the proper quantity to suit the driving condi-
tions, into the intake air mixture to slow down combustion, reduce the combustion temperature and reduce
NOx emissions. The amount of EGR is regulated by the EGR vacuum modulator according to the engine
load.
If even one the following conditions is fulfilled, the VSV is turned
ON by a signal from ECM. This results in atmospheric air acting
on the EGR valve, closing the EGR valve and shutting off the
exhaust gas (EGR cut−off).
Before the engine is warmed up
During deceleration (throttle valve closed) .
Light engine load (amount of intake air very small).
Engine idling.
Engine speed over 4,400 rpm.
High engine load (amount of intake air very large)
.
DTC No.DTC Detecting ConditionTrouble Area
P0401
After the engine is warmed up, the intake manifold absolute
pressure is lager than the valve calculated by the ECM while
the EGR system is ON
(2 trip detected logic)
EGR valve stuck closed
Open or short in VSV circuit for EGR
Vacuum or EGR hose disconnected
Manifold absolute pressure sensor
EGR VSV open or close malfunction
ECM
WIRING DIAGRAM
DI3ZT−01

A00407
System: (OFF) System: (ON)Air
GGAir
EE
Air Filter
− DIAGNOSTICSENGINE
DI−67
1996 RAV4 (RM447U)
TOYOTA hand−held tester
1 Check the connection of the vacuum hose, EGR hose (See page EC−5).
NG Repair or replace.
OK
2 Check the VSV for EGR.
PREPARATION:
Select the ACTIVE TEST mode on the TOYOTA hand−held tes-
ter.
CHECK:
Check operation of VSV, when it is operated by the TOYOTA
hand−held tester.
OK:
EGR system is OFF:
Air from pipe E is flowing out through the air filter.
EGR system is ON:
Air from pipe E is flowing out pipe G.
OK Go to step 4.
NG
3 Check operation of the VSV for EGR (See page SF−43).
NG Replace VSV for EGR.
OK
Check for open and short in harness and con-
nector between R/B No.6 and ECM
(See page IN−30).

DI−68
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U)
4 Check EGR vacuum modulator (See page EC−8).
NG Repair or replace.
OK
5 Check EGR valve (See page EC−8).
NG Repair or replace.
OK
6 Check manifold absolute pressure sensor (See page DI−21).
NG Repair or replace.
OK
Check and replace ECM (Se page IN−30).
OBDII scan tool (excluding TOYOTA hand−held tester)
1 Check the connection of vacuum hose, EGR hose (See page EC−5).
NG Repair or replace.
OK

− DIAGNOSTICSENGINE
DI−71
1996 RAV4 (RM447U)
DTC P0402 Exhaust Gas Recirculation Flow Excessive
Detected
CIRCUIT DESCRIPTION
Refer to Exhaust Gas Recirculation Flow Insufficient Detected on page DI−65.
DTC No.DTC Detecting ConditionTrouble Area
P0402
After the engine is warmed up, conditions (a) and (b) continue
(a) The intake manifold absolute pressure is larger than the
value calculated by the ECM while the EGR system is ON.
(b) Misfiring is detected during idling
(2 trip detection logic)EGR valve stuck open
Vacuum or EGR hose is connected to wrong post
Manifold absolute pressure sensor
ECM
See DTC P0140 for System Check Driving Pattern and Wiring Diagram.
INSPECTION PROCEDURE
HINT:
If DTC ”P0105” and / or ”P0106” and ”P0402” are output simultaneously, perform troubleshooting of
DTC ”P0105” first.
If DTC ”P0401” and ”P0402” are output simultaneously, perform troubleshooting of DTC ”P0402” first.
1 Check the connection of the vacuum hose, EGR hose (See page EC−5).
NG Repair or replace.
OK
2 Check EGR valve (See page EC−8).
NG Repair or replace.
OK
3 Check the VSV for EGR * .
* If you have TOYOTA hand−held tester, see page DI−65, step 2.
If you have no TOYOTA hand−held tester, see page DI−65, step 2.
OK Go to step 5.
NG
DI3ZU−01