oil viscosity TOYOTA RAV4 1996 Service Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1996, Model line: RAV4, Model: TOYOTA RAV4 1996Pages: 1354, PDF Size: 30.43 MB
Page 499 of 1354
Q06070
D02315
OK if hot
Add if hot
D00697
Ok if hot
Add if hot
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
DI−179
1996 RAV4 (RM447U)
7. BASIC INSPECTION
(a) Check the ATF level.
HINT:
The vehicle must have been driven so that the engine and
transaxle are at normal operating temperature.
ATF temperature: 70 − 80°C (158 − 176°F)
(1) Park the vehicle on a level surface, set the parking
brake.
(2) With the engine idling and the brake pedal de-
pressed, shift the shift lever into each gear from the
P position to L position smoothly and return to the
P position.
(3) Pull out the transaxle dipstick and wipe it clean.
(4) Push it back fully into the pipe.
(5) Pull it out and check that the fluid level is in the HOT
range.
If the level is at the low side of the hot range, add fluid.
Fluid type: ATF type T or equivalent
NOTICE:
Do not overfill.
(b) Check the transfer oil level.
(1) Park the vehicle on a level surface, set the parking
brake.
(2) Pull out the transfer dipstick and wipe it clean.
(3) Push it back fully into the pipe.
(4) Pull it out and check the oil level, as shown in the il-
lustration.
Oil grade: API GL−5
Oil viscosity: SAE 75W−90
Page 501 of 1354
Q06065
Q06076
D02315
OK if hot
Add if hot
D00699
D00700
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
DI−181
1996 RAV4 (RM447U)
(d) Replace the ATF.
NOTICE:
Do not overfill.
(1) Using a 10 mm hexagon wrench, remove the drain
plug, gasket and drain the fluid.
(2) Install a new gasket and the drain plug securely.
(3) Add new fluid through the filler pipe.
Fluid type: ATF type T or equivalent
Drain and refill: 3.3 liters (3.5 US qts, 2.9 lmp. qts)
(4) Start the engine and shift the selector into all the
positions from P through L and then shift into the P
position.
(5) With the engine idling, check the fluid level. Add
fluid up to the COOL level on the dipstick.
(6) Check the fluid level with the normal fluid tempera-
ture 70 − 80°C (158 − 176°F) and add as neces-
sary.
NOTICE:
Do not overfill.
(e) Replace the transfer oil.
(1) Using a 10 mm hexagon wrench, remove the drain
plug and drain the oil.
(2) Install the drain plug.
(3) Add new oil through the filler pipe.
Recommended oil:
Oil grade API GL−5
Viscosity SAE 75W−90
Capacity: 0.7 liters (0.7 US qts, 0.6 lmp. qts)
(4) Check the oil level and add as necessary.
NOTICE:
Do not overfill.
Page 976 of 1354
LU060−04
S01260
Oil Pressure Gauge
P13638
Adhesive
− LUBRICATIONOIL AND FILTER
LU−1
1996 RAV4 (RM447U)
OIL AND FILTER
INSPECTION
1. CHECK ENGINE OIL QUALITY
Check the oil for deterioration, entry of water, discoloring or thin-
ning.
If the quality is visibly poor, replace the oil.
Oil grade:
API grade SH, Energy − Conserving II multigrade en-
gine oil or ILSAC multigrade engine oil.
Recommended viscosity is as shown in the illustra-
tion.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the dip-
stick.
If low, check for leakage and add oil up to ”F” mark.
3. REMOVE OIL PRESSURE SWITCH, AND INSTALL OIL
PRESSURE GAUGE
4. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
5. CHECK OIL PRESSURE
Oil pressure:
At idle
29 kPa (0.3 kgf/cm
2, 4.3 psi) or more
At 3,000 rpm
245 − 490 kPa
(2.5 − 5.0 kgf/cm
2, 36 − 71 psi)
6. REMOVE OIL PRESSURE GAUGE AND REINSTALL
OIL PRESSURE SWITCH
(a) Remove the oil pressure gauge.
(b) Apply adhesive to 2 or 3 threads of the oil pressure switch.
Adhesive:
Part No.08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(c) Reinstall the oil pressure switch.
7. START ENGINE AND CHECK FOR LEAKS
Page 999 of 1354
Q08751
Q08752
Q10165
Filler Plug
Oil Level
0 − 5 mm
Drain Plug
Q08753
MX−4
− MANUAL TRANSAXLEMANUAL TRANSAXLE UNIT (2WD)
1996 RAV4 (RM447U)
10. REMOVE ENGINE LEFT MOUNTING INSULATOR SET
BOLT AND 2 NUTS
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
11. INSTALL ENGINE SUPPORT FIXTURE
12. TIE PS GEAR ASSEMBLY TO ENGINE SUPPORT FIX-
TURE BY CORD OR EQUIVALENT
13. REMOVE FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
14. RAISE VEHICLE
NOTICE:
Make sure that the vehicle is securely supported.
15. REMOVE LH AND RH ENGINE UNDER COVERS
16. DRAIN TRANSAXLE OIL
Oil grade: API GL−4 or GL−5
Viscosity: SAE 75W−90
Capacity: 3.9 liters (4.1 US qts, 3.4 Imp. qts)
Torque: 49 N·m (500 kgf·cm, 36 ft·lbf)
17. REMOVE LH AND RH FRONT DRIVE SHAFTS
(See page SA−18)
18. REMOVE FRONT EXHAUST PIPE
(a) Remove the 3 nuts and gasket from the exhaust manifold.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
(b) Remove the 2 bolts, gasket and pipe.
Torque: 48 N·m (490 kgf·cm, 35 ft·lbf)
19. REMOVE FRONT SUSPENSION CROSSMEMBER AS-
SEMBLY WITH STABILIZER BAR
(a) Support the front suspension crossmember with a jack.
(b) Disconnect the ring from the center exhaust pipe.
(c) Remove the 2 set bolts and nuts of the PS gear assembly.
Torque: 113 N·m (1,150 kgf·cm, 83 ft·lbf)
Page 1184 of 1354
W01215
SST
R10775
SST
R10762
SST
R10763
Less that 5 mm (0.20 in.) SA−70
− SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
1996 RAV4 (RM447U)
(b) Using SST, install a new oil seal.
SST 09554−22010
Oil seal drive in depth: 2.0 mm (0.079 in.)
(c) Apply MP grease to the oil seal lip.
7. INSTALL COMPANION FLANGE
(a) Using SST, install the companion flange on the shaft.
SST 09950−30010 (09951−03010, 09953−03010,
09954−03010, 09955−03040, 09956−03020)
(b) Coat the threads of a new nut with hypoid gear oil.
(c) Using SST to hold the flange, torque the nut.
SST 09330−00021
Torque: 108 N·m (1,100 kgf·cm, 80 ft·lbf)
(d) Adjust the preload of bearing on drive pinion (See page
SA−79).
8. STAKE DRIVE PINION NUT
9. INSTALL PROPELLER SHAFT (See page PR−2)
10. FILL DIFFERENTIAL WITH DIFFERENTIAL OIL
Torque: 49 N·m (500 kgf·cm, 36 ft·lbf)
Oil grade: Hypoid gear oil API GL−5
Recommended oil viscosity:
Above −18°C (0°F) SAE 90
Below −18°C (0°F) SAE 80W or 80W−90
Capacity: 0.9 liter (1.0 US qts, 0.8 lmp. qts)