wheel bolts TOYOTA RAV4 1996 Service Repair Manual

Z13290
SST
R10699
R10700
SST
BR0370
− BRAKEREAR DRUM BRAKE
BR−31
1996 RAV4 (RM447U)
5. REMOVE REAR SHOE
(a) Using SST, remove the shoe hold−down spring, cups and
pin.
SST 09718−00010
(b) Using a screwdriver, disconnect the parking brake cable
from the anchor plate.
(c) Using pliers, disconnect the parking brake cable from the
lever and remove the rear shoe together with the adjuster.
6. REMOVE ADJUSTER FROM REAR SHOE
(a) Remove the adjusting lever spring.
(b) Remove the adjuster together with the return spring.
7. DISCONNECT BRAKE LINE FROM WHEEL CYL-
INDER
Using SST, disconnect the brake line. Use a container to catch
the brake fluid.
SST 09023−00100
Torque: 15 N·m (155 kgf·cm, 11 ft·lbf)
8. REMOVE WHEEL CYLINDER
Remove the 2 bolts and the wheel cylinder.
Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
9. DISASSEMBLE WHEEL CYLINDER
Remove these parts from the wheel cylinder.
2 boots
2 pistons
2 piston cups
Spring

CL04S−02
Q06030
Matchmarks
Q06031
CL−16
− CLUTCHCLUTCH UNIT
1996 RAV4 (RM447U)
REMOVAL
1. REMOVE TRANSAXLE FROM ENGINE
(2WD: See page MX−2)
(4WD: See page MX−8)
2. REMOVE CLUTCH COVER AND DISC
(a) Place matchmarks on the flywheel and clutch cover.
(b) Loosen each set bolt one turn at a time until spring tension
is released.
(c) Remove the set bolts, and pull off the clutch cover with the
clutch disc.
NOTICE:
Do not drop the clutch disc.
3. REMOVE RELEASE BEARING AND FORK FROM
TRANSAXLE
(a) Remove the release bearing together with the fork and
then separate them.
(b) Remove the boot.

CL04U−02
Q06037
Flywheel
Side
SST
Q06038
Matchmarks8 2, 5
6
SST
3
7 1, 4
Q06039SST
Q06245
CL−18
− CLUTCHCLUTCH UNIT
1996 RAV4 (RM447U)
INSTALLATION
1. INSTALL CLUTCH DISC AND CLUTCH COVER ON
FLYWHEEL
(a) Insert SST in the clutch disc, and then set them and the
clutch cover in position.
SST 09301−00220
(b) Align the matchmarks on the clutch cover and flywheel.
(c) Temporarily tighten the topmost bolt from the 3 near the
knock pins.
HINT:
Temporarily tighten the No.3 bolt.
(d) Torque the bolts on the clutch cover in the order shown.
Torque: 19 N·m (195 kgf·cm, 14 ft·lbf)
2. CHECK DIAPHRAGM SPRING TIP ALIGNMENT
Using a dial indicator with roller instrument, check the dia-
phragm spring tip alignment.
Maximum non−alignment: 0.5 mm (0.020 in.)
If alignment is not as specified, using SST, adjust the dia-
phragm spring tip alignment.
SST 09333−00013
3. APPLY MOLYBDENUM DISULPHIDE LITHIUM BASE
GREASE (NLGI NO.2)
(a) Apply release hub grease to the following parts.
Release fork and hub contact point
Release fork and push rod contact point
Release fork pivot point
(b) Apply clutch spline grease.
Clutch disc spline
HINT:
Recommended grease part number 08887−01706 (100g).
4. INSTALL RELEASE BEARING AND FORK TO TRANS-
AXLE
Install the bearing to the release fork, and then install them to
the transaxle.
5. INSTALL TRANSAXLE TO ENGINE
(2WD: See page MX−2)
(4WD: See page MX−8)

Q06077NRP
Q06078
Neutral
Basic
Line
Groove
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
DI−183
1996 RAV4 (RM447U)
(3) Return the lever 2 notches to the NEUTRAL posi-
tion.
(4) Set the shift lever in the N position.
(5) While holding the lever lightly toward the ”R” posi-
tion side, tighten the shift lever nut.
(i) Adjust the park/neutral position switch.
If the engine will start with the shift selector in any position other
than the N or P position, adjustment is required.
(1) Loosen the park/neutral position switch bolts and
set the shift selector to the N position.
(2) Align the groove and neutral basic line.
(3) Hold in position and tighten the bolts.
Torque: 5.4 N·m(55 kgf·cm,48 in·lbf)
(j) Inspect the idle speed.
Idle speed: 750 ± 50 rpm (In N position and A/C OFF)
8. MECHANICAL SYSTEM TESTS
(a) Measure the stall speed.
The object of this test is to check the overall performance of the transaxle and engine by measuring
the stall speeds in the D and R positions.
NOTICE:
Do the test at normal operating ATF temperature 50 − 80°C (122 − 176°F).
Do not continuously run this test longer than 5 seconds.
To ensure safety, conduct this test in a wide, clear, level area which provides good traction.
The stall test should always be carried out in pairs. One technician should observe the condi-
tions of wheels or wheel stoppers outside the vehicle while the other is doing the test.
(1) Chock the 4 wheels.
(2) Connect OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(3) Fully apply the parking brake.
(4) Keep your left foot pressed firmly on the brake pedal.
(5) Start the engine.
(6) Shift into the D position. Press all the way down on the accelerator pedal with your right foot.
Quickly read the stall speed at this time.
Stall speed: 2,400 ± 150 rpm
(7) Do the same test in R position.
Stall speed: 2,400 ± 150 rpm
Evaluation:
ProblemPossible cause
Stall speed low in D and R positions
Engine output may be insufficient
Stator one−way clutch is operating properly
HINT:
If more than 600 rpm below the specified value, the torque converter clutch could
be faulty

S01352
Ground Strap EM−26
− ENGINE MECHANICALTIMING BELT
1996 RAV4 (RM447U)
19. INSTALL RH ENGINE MOUNTING INSULATOR
(a) Attach the mounting insulator to the body and mounting
bracket with the 4 bolts and 2 nuts.
(b) Tighten the 3 bolts holding the mounting insulator to the
body.
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
(c) Tighten the 2 nuts and bolt holding the mounting insulator
to the mounting bracket.
Torque:
37 N·m (380 kgf·cm, 27 ft·lbf) for bolt
52 N·m (530 kgf·cm, 38 ft·lbf) for nut
20. INSTALL AND ADJUST PS PUMP DRIVE BELT
21. INSTALL RH ENGINE UNDER COVER
22. INSTALL RH FRONT WHEEL
23. w/ ABS:
INSTALL NO. 3 ABS ACTUATOR BRACKET (See page
BR−41)
24. INSTALL GENERATOR BRACKET
(a) Install the bracket with the 3 bolts.
Torque: 42 N·m (425 kgf·cm, 31 ft·lbf)
(b) Connect the ground strap connector.
25. INSTALL GENERATOR (See page CH−19)
26. INSTALL WIRE HARNESS BRACKET FOR DLC1
27. INSTALL PS RESERVOIR BRACKET AND RES-
ERVOIR

S01374
Cover
Connector
− ENGINE MECHANICALENGINE UNIT
EM−79
1996 RAV4 (RM447U)
25. INSTALL GENERATOR (See page CH−19)
26. INSTALL CHARCOAL CANISTER
27. CONNECT ENGINE WIRE TO RELAY BOX NO. 2
(a) Connect the engine wire to the relay block No.2 with the
2 nuts.
(b) Connect the connector.
(c) Install the upper cover.
(d) Connect the relay block No. 2 to the body with the 2 bolts.
28. INSTALL ACCELERATOR CABLE TO THROTTLE
BODY, CABLE BRACKET AND CLAMPS
29. INSTALL AIR CLEANER CASE AND CAP
30. INSTALL BATTERY
31. FILL WITH TRANSAXLE OIL
32. FILL WITH ENGINE OIL
33. FILL WITH ENGINE COOLANT
34. START ENGINE AND CHECK FOR LEAKS
35. PERFORM ENGINE ADJUSTMENT
36. CHECK FRONT WHEEL ALIGNMENT
37. INSTALL ENGINE UNDER COVERS
38. INSTALL ENGINE HOOD
39. ROAD TEST VEHICLE
Check for abnormal noises, shock slippage, correct shift points
and smooth operation.
40. RECHECK ENGINE COOLANT AND OIL LEVELS

P15297
M/T
EM1BB−02
P15299
A/T
P13432
P15304
RH Engine
Mounting
Bracket
PS Pump
Bracket
S01580
1
3
2
− ENGINE MECHANICALCYLINDER BLOCK
EM−81
1996 RAV4 (RM447U)
DISASSEMBLY
1. M/T:
REMOVE FLYWHEEL
Remove the 8 bolts and flywheel.
2. A/T:
REMOVE DRIVE PLATE
Remove the 8 bolts, front plate, drive plate and rear spacer.
3. REMOVE REAR END PLATE
Remove the bolt and end plate.
4. INSTALL ENGINE TO ENGINE STAND FOR DIS-
ASSEMBLY
5. REMOVE RH ENGINE MOUNTING BRACKET
Remove the 3 bolts and mounting bracket.
6. REMOVE PS PUMP BRACKET
Remove the 3 bolts and PS pump bracket.
7. REMOVE TIMING BELT AND PULLEYS (See page
EM−15)
8. REMOVE CYLINDER HEAD (See page EM−33)
9. REMOVE OIL PAN AND OIL PUMP (See page LU−7)
10. REMOVE GENERATOR DRIVE BELT ADJUSTING
BAR, WATER PUMP AND WATER PUMP COVER AS-
SEMBLY
(a) Remove the bolt and adjusting bar.
(b) Remove the 3 bolts in the sequence shown, remove the
water pump, water pump cover assembly and O−ring.
11. REMOVE OIL COOLER (See page LU−18)

Z17349
3
1
2
P15304
RH Engine
Mounting
Bracket
PS Pump
Bracket
P13432
EM7333
P15298
3
1
2 M/T
5
8 7
6
4
− ENGINE MECHANICALCYLINDER BLOCK
EM−103
1996 RAV4 (RM447U)
(b) Install the water pump with the 3 bolts. Tighten the bolts
in the sequence shown.
Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
(c) Install the adjusting bar with the bolt.
Torque: 22 N·m (220 kgf·cm, 16 ft·lbf)
14. INSTALL OIL PUMP AND OIL PAN (See page LU−14)
15. INSTALL CYLINDER HEAD (See page EM−55)
16. INSTALL TIMING BELT AND PULLEYS (See page
EM−20)
17. INSTALL RH ENGINE MOUNTING BRACKET
Install the mounting bracket with the 3 bolts.
Torque: 52 N·m (530 kgf·cm, 38 ft·lbf)
18. INSTALL PS PUMP BRACKET
Install the PS pump bracket with the 3 bolts.
Torque: 43 N·m (440 kgf·cm, 32 ft·lbf)
19. DISCONNECT ENGINE FROM ENGINE STAND
20. INSTALL REAR END PLATE
Install the rear end plate with the bolt.
Torque: 9.3 N·m (95 kgf·cm, 82 in.·lbf)
21. M/T:
INSTALL FLYWHEEL
(a) Apply adhesive to 2 or 3 threads of the bolt end.
Adhesive:
Part No. 08833−00070, THREE BOND 1324 or equiva-
lent
(b) Install the flywheel on the crankshaft.
(c) Install and uniformly tighten the 8 bolts, in several passes,
in the sequence shown.
Torque: 88 N·m (900 kgf·cm, 65 ft·lbf)

Q08751
Q08752
Q10165
Filler Plug
Oil Level
0 − 5 mm
Drain Plug
Q08753
MX−4
− MANUAL TRANSAXLEMANUAL TRANSAXLE UNIT (2WD)
1996 RAV4 (RM447U)
10. REMOVE ENGINE LEFT MOUNTING INSULATOR SET
BOLT AND 2 NUTS
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
11. INSTALL ENGINE SUPPORT FIXTURE
12. TIE PS GEAR ASSEMBLY TO ENGINE SUPPORT FIX-
TURE BY CORD OR EQUIVALENT
13. REMOVE FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
14. RAISE VEHICLE
NOTICE:
Make sure that the vehicle is securely supported.
15. REMOVE LH AND RH ENGINE UNDER COVERS
16. DRAIN TRANSAXLE OIL
Oil grade: API GL−4 or GL−5
Viscosity: SAE 75W−90
Capacity: 3.9 liters (4.1 US qts, 3.4 Imp. qts)
Torque: 49 N·m (500 kgf·cm, 36 ft·lbf)
17. REMOVE LH AND RH FRONT DRIVE SHAFTS
(See page SA−18)
18. REMOVE FRONT EXHAUST PIPE
(a) Remove the 3 nuts and gasket from the exhaust manifold.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
(b) Remove the 2 bolts, gasket and pipe.
Torque: 48 N·m (490 kgf·cm, 35 ft·lbf)
19. REMOVE FRONT SUSPENSION CROSSMEMBER AS-
SEMBLY WITH STABILIZER BAR
(a) Support the front suspension crossmember with a jack.
(b) Disconnect the ring from the center exhaust pipe.
(c) Remove the 2 set bolts and nuts of the PS gear assembly.
Torque: 113 N·m (1,150 kgf·cm, 83 ft·lbf)

AB0163
Wire Harness
Diameter
Stripped Wire Harness Section
R05748
L
M RS−14
− SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
1996 RAV4 (RM447U)
2. DEPLOYMENT WHEN DISPOSING OF STEERING
WHEEL PAD ONLY
NOTICE:
When disposing of the steering wheel pad (with air-
bag) only, never use the customers vehicle to deploy
the airbag.
Be sure to follow the procedure given below when de-
ploying the airbag.
HINT:
Have a battery ready as the power source to deploy the airbag.
(a) Remove the steering wheel pad (See page SR−12).
CAUTION:
When storing the steering wheel pad, keep the upper sur-
face of the pad facing upward.
(b) Using a service−purpose wire harness for the vehicle tie
down the steering wheel pad to the disc wheel
Wire harness: Stripped wire harness section
1.25 mm
2 or more (0.0019 in.2 or more).
CAUTION:
If a wire harness which is too thin or some other thing is
used to tie down the steering wheel pad, it may be snapped
by the shock when the airbag is deployed. This is highly
dangerous. Always use a wire harness for vehicle use
which is at least 1.25 mm
2 (0.0019 in.2).
HINT:
To calculate the square of the stripped wire harness section:
Square = 3.14 X (Diameter)
2 divided by 4
(1) .Install the 2 bolts with washer in the 2 bolt holes in
the steering wheel pad.
Bolt:
L: 35.0 mm (1.387 in.)
M: 6.0 mm (0.236 in.)
Pitch: 1.0 mm (0.039 in.)
NOTICE:
Tighten the bolts by hand until the bolts become diffi-
cult to turn.
Do not tighten the bolts too much.