ignition TOYOTA RAV4 2013 XA40 / 4.G Owners Manual

3
1
8 7
6
5
4
3
2
RAV4_OM_OM42809U_(U)
9
4-1. Before drivingDriving the vehicle ............. 164
Cargo and luggage............ 176
Vehicle load limits ............. 180
Trailer towing..................... 181
Dinghy towing.................... 196
4-2. Driving procedures Engine (ignition) switch (vehicles without a
smart key system) ........... 197
Engine (ignition) switch (vehicles with a
smart key system) ........... 200
Automatic transmission ..... 207
Turn signal lever................ 214
Parking brake .................... 215
Horn .................................. 216
4-3. Operating the lights and wipers
Headlight switch ................ 217
Automatic High Beam ....... 221
Fog light switch ................. 228
Windshield wipers and washer ..................... 229
Rear window wiper and washer ..................... 234 4-4. Refueling
Opening the fuel tank cap................................... 237
4-5. Using the driving support systems
Cruise control .................... 241
LDA (Lane Departure Alert)..... 245
Intuitive parking assist ....... 253
All-wheel drive lock switch (AWD models) ...... 259
Driving assist systems ....... 260
BSM (Blind Spot Monitor)......... 266
• The Blind Spot Monitor function.......................... 270
• The Rear Cross Traffic Alert function ................. 273
4-6. Driving tips Winter driving tips .............. 276
Utility vehicle precautions ...................... 281
4Driving

771-2. Theft deterrent system
RAV4_OM_OM42809U_(U)
1
For safety and security
Engine immobilizer system
Vehicles without a smart key
system
The indicator light flashes after
the key has been removed from
the engine switch to indicate that
the system is operating.
The indicator light stops flashing
after the registered key has been
inserted into the engine switch to
indicate that the system has been
canceled.
Vehicles with a smart key system
The indicator light flashes after the engine switch has been turned off
to indicate that the system is operating.
The indicator light stops flashing after the engine switch has been
turned to ACCESSORY or IGNITION ON mode to indicate that the
system has been canceled.
■ System maintenance
The vehicle has a maintenance-free type engine immobilizer system.
■ Conditions that may cause the system to malfunction
●If the grip portion of the key is in contact with a metallic object
● If the key is in close proximity to or touching a key to the security system
(key with a built-in transponder chip) of another vehicle
The vehicle’s keys have built-in transponder chips that prevent
the engine from starting if a key has not been previously regis-
tered in the vehicle’s on-board computer.
Never leave the keys inside the vehicle when you leave the vehi-
cle.

84
RAV4_OM_OM42809U_(U)
2. Instrument cluster
*1: These lights turn on when the engine switch is turned to the “ON” position(vehicles without a smart key system) or IGNITION ON mode (vehicles with
a smart key system), to indicate that a system check is being performed.
They will turn off after the engine is started, or after a few seconds. There
may be a malfunction in a system if the lights do not come on, or turn off.
Have the vehicle inspected by your Toyota dealer.
*2: The light flashes to indicate a malfunction.
*3: The light comes on to indicate that the intuitive parking assist sensor is dirtyor covered with ice.
Seat belt reminder light
(P. 507)
*1
(yellow)
(if equipped)
Automatic High Beam
warning light ( P. 505)
Low fuel level warning
light (P. 507)*1Low washer fluid
warning light ( P. 507)
*1High engine coolant
temperature warning
light (P. 507)
(yellow)
(if equipped)
Smart key system
indicator ( P. 506, 511)
*1
(U.S.A.)
Maintenance required
reminder light ( P. 508)*2, 3
(if equipped)
Intuitive parking assist
indicator (P. 506, 509)
*1
(if equipped)
Automatic transmission
fluid temperature
warning light ( P. 505)
(yellow)
(if equipped)
LDA warning lights
(P. 505)
*1
(if equipped)
Dynamic Torque Control
AWD system warning
light ( P. 509)*1
(if equipped)
BSM warning light
(P. 505)
(yellow)
Cruise control warning
light ( P. 505)*1
(if equipped)
Tire pressure warning
light (P. 508)

86
RAV4_OM_OM42809U_(U)
2. Instrument cluster
*1: These lights turn on when the engine switch is turned to the “ON” position(vehicles without a smart key system) or IGNITION ON mode (vehicles with
a smart key system), to indicate that a system check is being performed.
They will turn off after the engine is started, or after a few seconds. There
may be a malfunction in a system if the lights do not come on, or turn off.
Have the vehicle inspected by your Toyota dealer.
*2: The light flashes to indicate that the system is operating.
*3: In order to confirm operation, the BS M outside rear view mirror indicators
illuminate in the following situations:
• When the engine switch is turned to the “ON” position (vehicles without a smart key system) or IGNITION ON mode (vehicles with a smart key sys-
tem) while the BSM main switch is set to ON.
• When the BSM main switch is set to ON while the engine switch is in the “ON” position (vehicles without a smart key system) or IGNITION ON
mode (vehicles with a smart key system).
If the system is functioning correctly, the BSM outside rear view mirror indi-
cators will turn off after a few seconds.
If the BSM outside rear view mirror indicators do not illuminate or do not
turn off, there may be a malfunction with the system. If this occurs, have the
vehicle inspected by your Toyota dealer.
CAUTION
■ If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not
come on when you start the engine, this could mean that these systems are
not available to help protect you in an accident, which could result in death
or serious injury. Have the vehicle inspected by your Toyota dealer immedi-
ately if this occurs.
NOTICE
■ To prevent damage to the engine and its components
The engine may be overheating if the high engine coolant temperature
warning light flashes or turns on. In this case, immediately stop the vehicle
in a safe place, and check the engine after it has cooled completely.
(P. 546)

122
RAV4_OM_OM42809U_(U)
3-2. Opening, closing and locking the doors
Move the inside lock button to the lock position.
Close the door.
Vehicles without a smart key system
The door cannot be locked if the key is in the engine switch.
Vehicles with a smart key system
The door cannot be locked if the engine switch is in ACCESSORY or
IGNITION ON mode, or the electronic key is left inside the vehicle.
Depending on the position of the electronic key, the key may not be
detected correctly and the door may be locked.
The door cannot be opened from
inside the vehicle when the lock is
set.
Unlock
Lock
These locks can be set to prevent
children from opening the rear
doors. Push down on each rear
door switch to lock both rear doors.
Locking the front doors from the outside without a key
Rear door child-protector lock
1
2
1
2

RAV4_OM_OM42809U_(U)
1333-2. Opening, closing and locking the doors
3
Operation of each component
CAUTION
■Power back door (if equipped)
Observe the following precautions when operating the power back door.
Failure to do so may cause death or serious injury.
●Check the safety of the surrounding area to make sure there are no obsta-
cles or anything that could cause any of your belongings to get caught.
● If anyone is in the vicinity, make sure they are safe and let them know that
the back door is about to open or close.
● If the power back door main switch is turned off while the back door is
operating during automatic operation, the back door stops operating. Take
extra care when on an incline, as the back door may open or close sud-
denly.
● If the operating conditions of the power back door are no longer met, a
buzzer may sound and the back door may stop opening or closing. The
back door then has to be operated manually. Take extra care in this situa-
tion, as the back door may move abruptly.
● On an incline, the back door may suddenly shut after it opens automati-
cally. Make sure the back door is fully open and secure.
● In the following situations, the power back door may detect an abnormality
and automatic operation may be stopped. In this case, the back door has
to be operated manually. Take extra care in this situation, as the stopped
back door may suddenly open or close, causing an accident.
• When the back door contacts an obstacle
• When the battery voltage suddenly drops, such as when the engine
switch is turned to the “ON” position (vehicles without a smart key sys-
tem) or IGNITION ON mode (vehicles with a smart key system) or the
engine is started during automatic operation

143
RAV4_OM_OM42809U_(U)
3-3. Adjusting the seats
3
Operation of each component
Driving position memor y
Check that the shift lever is in P.
Turn the engine switch to the “ON” position (vehicles without a
smart key system) or IGNITION ON mode (vehicles with a smart
key system).
Adjust the driver’s seat position.
While pressing the “SET” but-
ton, press button “1” or “2” until
the signal beeps.
If the selected button has already
been preset, the previously
recorded position will be overwrit-
ten.
: If equipped
Your preferred driving position (th e position of the driver’s seat)
can be memorized and recalled by pressing a button. It is also
possible to set this function to activate automatically when the
doors are unlocked.
Two different driving positions can be entered into memory.
Entering a position to memory
1
2
3
4

144
RAV4_OM_OM42809U_(U)
3-3. Adjusting the seats
Check that the shift lever is in P.
Turn the engine switch to the “ON” position (vehicles without a
smart key system) or IGNITION ON mode (vehicles with a smart
key system).
Press button “1” or “2” to recall
the desired position.
Recalling the memorized position
1
2
3

RAV4_OM_OM42809U_(U)
1453-3. Adjusting the seats
3
Operation of each component
A desired driving position can be recalled linked with the unlocking of
the door.
■Setting procedure
Record your driving position to button “1” or “2” before performing
the following:
Carrying only the key to which you want to link the driving position,
shift the shift lever to P and then close the driver’s door.
If 2 or more keys are in the vehicle, the driving position cannot be
linked properly.
Turn the engine switch to IGNITION ON mode and recall the
position which you want to link.
While pressing the button to
recall the position, press the
driver’s door lock switch
(either lock or unlock) until
the signal beeps.
The driving position is recalled
when the driver’s door is
unlocked using the entry func-
tion or wireless remote control
and the driver’s door is opened.
Linking driving position memo ry with door unlock operation
(vehicles with a smart key system)
1
2

146
RAV4_OM_OM42809U_(U)
3-3. Adjusting the seats
■Cancelation procedure
Carry only the key for which you want to cancel the linked door
unlock operation.
If 2 or more keys are in the vehicle, the driving position cannot be
canceled properly.
Turn the engine switch to IGNITION ON mode.
While pressing the “SET” button, press the driver’s door lock
switch (either lock or unlock) until the signal beeps.
■When you want to stop the position recall operation part-way through
Perform any of the following operations:
● Press the “SET” button.
● Press button “1” or “2”.
● Adjust the seat using the switches.
■ Operating the driving position memo ry after turning the engine off
Memorized seat positions can be activated up to 180 seconds after the
driver’s door is opened and another 60 seconds after it is closed again.
■ If the battery is disconnected
The memorized positions are erased when the battery is disconnected.
CAUTION
■Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear
passenger or squeeze your body against the steering wheel.
1
2