air filter TOYOTA RAV4 HYBRID 2019 Warranties & Maintenance Guides (in English)
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2019, Model line: RAV4 HYBRID, Model: TOYOTA RAV4 HYBRID 2019Pages: 68, PDF Size: 0.41 MB
Page 49 of 68

47Maintenance Log
75,000 miles or 90 months
Add Toyota EFI Tank Additive or equivalent (Hawaii, Puerto Rico, Saipan and American Samoa only) 
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Rotate tires
 Visually inspect brake linings/drums and brake pads/discs
NOTE: If 0W-16 oil WAS NOT used at the last oil change, replace engine oil and oil filter.2
Inspect the following:
  _
Ball joints and dust covers  _
  Exhaust pipes and mountings
  _
Brake lines and hoses _
  Radiator, condenser and/or intercooler
  _
Cabin air filter _
 Steering gear 
  _
Drive shaft boots _
  Steering linkage and boots   
_  
Engine/Inverter coolant
4 
 
 
 
 
 
  
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads:Inspect engine air filter
Replace engine oil and oil filter2
Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:5
Replace engine oil and oil filter2
Tighten nuts and bolts on chassis and body
Repeated trips of less than five miles in temperatures below 32°F / 0°C:
Replace engine oil and oil filter2
Extensive idling and/or low speed driving for a long distance such as police, taxi or 
door-to-door delivery use:
Clean HV battery cooling intake filter 
Replace engine oil and oil filter2
NOTE: Driving in heavy traffic, on dirt roads or in urban, dusty or desert areas may shorten 
the life of the cabin air filter. Replacement may be needed if you notice reduced air flow 
from the air conditioner and heater or if the windows fog easily when you use the “Fresh” 
mode. Consult your dealer if any of these conditions occur.
MAINTENANCE LOG
MAINTENANCE
1  Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed 
component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect 
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant  
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on 
inspection results.
2 
 Reset the oil replacement reminder light (“MAINT REQD”) or the message “OIL MAINTENANCE REQUIRED” on the  
multi-information display after maintenance at every 5,000 miles.
3 
Perform these service items only if you drive primarily under the conditions indicated.4   
 Refer to “Engine/Inverter Coolant” in the “Explanation of Maintenance Items” section in the back of this guide for  
more information.
5 
Not all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.
DEALER SERVICE VERIFICATION:
D
ATE:
MILEAGE: 
Page 50 of 68

48Maintenance Log
MAINTENANCE LOG
MAINTENANCE
80,000 miles or 96 months
 Add Toyota EFI Tank Additive or equivalent 
(Hawaii, Puerto Rico, Saipan and 
American Samoa only) 
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Replace engine oil and oil filter2
Rotate tires
 Visually inspect brake linings/drums  
and brake pads/discs
Additional Maintenance Items for 
Special Operating Conditions3
Driving on dirt roads or dusty roads:Inspect ball joints and dust covers
Inspect drive shaft boots
Inspect engine air filter
Inspect steering linkage and boots
 Tighten nuts and bolts on chassis  
and body 
Driving while towing, using a car-top 
carrier, or heavy vehicle loading:
6
 Tighten nuts and bolts on chassis  
and body
Extensive idling and/or low speed driving 
for a long distance such as police, taxi  
or door-to-door delivery use:
Clean HV battery cooling intake filter
85,000 miles or 102 months 
 Add Toyota EFI Tank Additive or equivalent 
(Hawaii, Puerto Rico, Saipan and 
American Samoa only) 
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Rotate tires
 Visually inspect brake linings/drums  
and brake pads/discs
NOTE: If 0W-16 oil WAS NOT used at 
the last oil change, replace engine oil 
and oil filter.
2
Additional Maintenance Items for 
Special Operating Conditions3
Driving on dirt roads or dusty roads:Inspect ball joints and dust covers
Inspect drive shaft boots
Inspect engine air filter
Inspect steering linkage and boots
 Replace engine oil and oil filter2
 Tighten nuts and bolts on chassis  
and body
Driving while towing, using a car-top 
carrier, or heavy vehicle loading:
6
Replace engine oil and oil filter2
 Tighten nuts and bolts on chassis  
and body
Repeated trips of less than five miles in 
temperatures below 32°F / 0°C:
Replace engine oil and oil filter2
Extensive idling and/or low speed driving 
for a long distance such as police, taxi  
or door-to-door delivery use:
Clean HV battery cooling intake filter
Replace engine oil and oil filter2
DEALER SERVICE VERIFICATION:
D
ATE:
MILEAGE:D
EALER SERVICE VERIFICATION:
D
ATE:
MILEAGE: 
Page 51 of 68

49Maintenance Log
MAINTENANCE LOG
MAINTENANCE
90,000 miles or 108 months
 Add Toyota EFI Tank Additive or equivalent (Hawaii, Puerto Rico, Saipan and American Samoa only) 
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Replace cabin air filter
Replace engine air filter
Replace engine oil and oil filter2
Rotate tires
Inspect the following:
  _
 Automatic transmission for signs of leakage
  _
Ball joints and dust covers
  _
Brake lines and hoses   
  _
 Brake linings/drums and brake pads/discs
4
  _
Drive shaft boots
  _
Engine/Inverter coolant
5
  _
Exhaust pipes and mountings 
 
 
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads:Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:6
Tighten nuts and bolts on chassis and body 
Extensive idling and/or low speed driving for a long distance such as police, taxi or 
door-to-door delivery use:
Clean HV battery cooling intake filter 
 
  _
 Fuel lines and connections, fuel tank band 
and fuel tank vapor vent system hoses
  _
Fuel tank cap gasket
  _
Radiator, condenser and/or intercooler
  _
Rear differential oil 
  _
Steering gear
  _
Steering linkage and boots
1  Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed 
component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect 
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant  
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on 
inspection results.
2 
 Reset the oil replacement reminder light (“MAINT REQD”) or the message “OIL MAINTENANCE REQUIRED” on the  
multi-information display after maintenance at every 5,000 miles.
3 
Perform these service items only if you drive primarily under the conditions indicated. 4  Inspect thickness measurement and disc runout.5    
   
Refer to “Engine/Inverter Coolant” in the “Explanation of Maintenance Items” section in the back of this guide for  
more information.
6 
Not all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.
DEALER SERVICE VERIFICATION:
D
ATE:
MILEAGE: 
Page 52 of 68

50Maintenance Log
MAINTENANCE LOG
MAINTENANCE
95,000 miles or 114 months 
 Add Toyota EFI Tank Additive or equivalent 
(Hawaii, Puerto Rico, Saipan and 
American Samoa only) 
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Rotate tires
 Visually inspect brake linings/drums  
and brake pads/discs
NOTE: If 0W-16 oil WAS NOT used at 
the last oil change, replace engine oil 
and oil filter.
2
Additional Maintenance Items for 
Special Operating Conditions3
Driving on dirt roads or dusty roads:Inspect ball joints and dust covers
Inspect drive shaft boots
Inspect engine air filter
Inspect steering linkage and boots
Replace engine oil and oil filter2
 Tighten nuts and bolts on chassis  
and body
Driving while towing, using a car-top 
carrier, or heavy vehicle loading:
6
 Replace engine oil and oil filter2 
 Tighten nuts and bolts on chassis  
and body
 Repeated trips of less than five miles in 
temperatures below 32°F / 0°C:
Replace engine oil and oil filter2
Extensive idling and/or low speed driving 
for a long distance such as police, taxi  
or door-to-door delivery use:
Clean HV battery cooling intake filter
Replace engine oil and oil filter2
100,000 miles or 120 months 
 Add Toyota EFI Tank Additive or equivalent 
(Hawaii, Puerto Rico, Saipan and 
American Samoa only) 
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Replace engine/inverter coolant4
Replace engine oil and oil filter2
Rotate tires
 Visually inspect brake linings/drums  
and brake pads/discs
Additional Maintenance Items for 
Special Operating Conditions3
Driving on dirt roads or dusty roads:Inspect ball joints and dust covers
Inspect drive shaft boots
Inspect engine air filter
Inspect steering linkage and boots
 Tighten nuts and bolts on chassis  
and body
Driving while towing, using a car-top 
carrier, or heavy vehicle loading:
6
 Tighten nuts and bolts on chassis  
and body
Extensive idling and/or low speed driving 
for a long distance such as police, taxi  
or door-to-door delivery use:
Clean HV battery cooling intake filter
DEALER SERVICE VERIFICATION:
D
ATE:
MILEAGE:D
EALER SERVICE VERIFICATION:
D
ATE:
MILEAGE: 
Page 53 of 68

51Maintenance Log
1  Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed 
component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect 
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant  
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on 
inspection results.
2 
 Reset the oil replacement reminder light (“MAINT REQD”) or the message “OIL MAINTENANCE REQUIRED” on the  
multi-information display after maintenance at every 5,000 miles.
3 
Perform these service items only if you drive primarily under the conditions indicated.4  Initial engine coolant replacement at 100,000 miles/120 months. Replace every 50,000 miles/60 months thereafter 
Initial inverter coolant replacement at 150,000 miles/180 months. Replace every 50,000 miles/60 months thereafter. Refer 
to “Engine/Inverter Coolant” in the “Explanation of Maintenance Items” section in the back of this guide for more information.
5   
   
Refer to “Engine/Inverter Coolant” in the “Explanation of Maintenance Items” section in the back of this guide for  
more information.
6 
Not all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.
105,000 miles or 126 months
Add Toyota EFI Tank Additive or equivalent (Hawaii, Puerto Rico, Saipan and American Samoa only) 
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Rotate tires
 Visually inspect brake linings/drums and brake pads/discs 
NOTE: If 0W-16 oil WAS NOT used at the last oil change, replace engine oil and oil filter.2
Inspect the following:
  _
Ball joints and dust covers  _
  Exhaust pipes and mountings
  _
Brake lines and hoses _
  Radiator, condenser and/or intercooler
  _
Cabin air filter _
 Steering gear 
  _
Drive shaft boots _
  Steering linkage and boots   
_  
Engine/Inverter coolant
5  
 
 
 
 
 
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads:Inspect engine air filter
Replace engine oil and oil filter2
Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:6
Replace engine oil and oil filter2
Tighten nuts and bolts on chassis and body
Repeated trips of less than five miles in temperatures below 32°F / 0°C:
Replace engine oil and oil filter2
Extensive idling and/or low speed driving for a long distance such as police, taxi or 
door-to-door delivery use:
Clean HV battery cooling intake filter 
Replace engine oil and oil filter2 
 
DEALER SERVICE VERIFICATION:
D
ATE: 
MILEAGE:
NOTE: Driving in heavy traffic, on dirt roads or in urban, dusty or desert areas may shorten 
the life of the cabin air filter. Replacement may be needed if you notice reduced air flow 
from the air conditioner and heater or if the windows fog easily when you use the “Fresh” 
mode. Consult your dealer if any of these conditions occur.
MAINTENANCE LOG
MAINTENANCE 
Page 54 of 68

52Maintenance Log
MAINTENANCE LOG
MAINTENANCE
110,000 miles or 132 months
 Add Toyota EFI Tank Additive or equivalent 
(Hawaii, Puerto Rico, Saipan and 
American Samoa only) 
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Replace engine oil and oil filter2
Rotate tires
 Visually inspect brake linings/drums  
and brake pads/discs
Additional Maintenance Items for 
Special Operating Conditions3
Driving on dirt roads or dusty roads:Inspect ball joints and dust covers
Inspect drive shaft boots
Inspect engine air filter
Inspect steering linkage and boots
 Tighten nuts and bolts on chassis  
and body 
Driving while towing, using a car-top 
carrier, or heavy vehicle loading:
7
 Tighten nuts and bolts on chassis  
and body
Extensive idling and/or low speed driving 
for a long distance such as police, taxi  
or door-to-door delivery use:
Clean HV battery cooling intake filter
115,000 miles or 138 months
 Add Toyota EFI Tank Additive or equivalent 
(Hawaii, Puerto Rico, Saipan and 
American Samoa only) 
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Rotate tires
 Visually inspect brake linings/drums  
and brake pads/discs
NOTE: If 0W-16 oil WAS NOT used at 
the last oil change, replace engine oil 
and oil filter.
2
Additional Maintenance Items for 
Special Operating Conditions3
Driving on dirt roads or dusty roads:Inspect ball joints and dust covers
Inspect drive shaft boots
Inspect engine air filter
Inspect steering linkage and boots
Replace engine oil and oil filter2
 Tighten nuts and bolts on chassis  
and body
Driving while towing, using a car-top 
carrier, or heavy vehicle loading:
7
Replace engine oil and oil filter2
 Tighten nuts and bolts on chassis  
and body
Repeated trips of less than five miles in 
temperatures below 32°F / 0°C:
Replace engine oil and oil filter2
Extensive idling and/or low speed driving 
for a long distance such as police, taxi  
or door-to-door delivery use:
Clean HV battery cooling intake filter
Replace engine oil and oil filter2
 
DEALER SERVICE VERIFICATION:
D
ATE:
MILEAGE:D
EALER SERVICE VERIFICATION:
D
ATE:
MILEAGE: 
Page 55 of 68

53Maintenance Log
MAINTENANCE LOG
MAINTENANCE
120,000 miles or 144 months
Add Toyota EFI Tank Additive or equivalent (Hawaii, Puerto Rico, Saipan and American Samoa only) 
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Replace cabin air filter
Replace engine air filter
Replace engine oil and oil filter2
Replace spark plugs4 
Rotate tires
Inspect the following:
  _
 Automatic transmission for signs of leakage
  _
Ball joints and dust covers
  _
Brake lines and hoses
  _
 Brake linings/drums and brake pads/discs
5
  _
Drive shaft boots 
  _
Engine/Inverter coolant6 
_  Exhaust pipes and mountings 
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads:Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:7
Replace automatic transmission fluid
Replace rear differential oil 
Tighten nuts and bolts on chassis and body
Extensive idling and/or low speed driving for a long distance such as police, taxi or 
door-to-door delivery use:
Clean HV battery cooling intake filter 
 
1
  Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed 
component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect 
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant  
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on 
inspection results.
2 
 Reset the oil replacement reminder light (“MAINT REQD”) or the message “OIL MAINTENANCE REQUIRED” on the  
multi-information display after maintenance at every 5,000 miles.
3 
Perform these service items only if you drive primarily under the conditions indicated.4   Maintenance services of spark plugs are required under the terms of the Emissions Control Warranty. 5  Inspect thickness measurement and disc runout.6   
 Refer to “Engine/Inverter Coolant” in the “Explanation of Maintenance Items” section in the back of this guide for  
more information.
7 
Not all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.
  _
 Fuel lines and connections, fuel tank band 
and fuel tank vapor vent system hoses
  _
Fuel tank cap gasket
  _
Radiator, condenser and/or intercooler
  _
Rear differential oil 
  _
Steering gear
  _
Steering linkage and boots
DEALER SERVICE VERIFICATION:
D
ATE:
MILEAGE: 
Page 56 of 68

54Maintenance Log
MAINTENANCE
EXPLANATION OF MAINTENANCE ITEMS
T
he following descriptions are  
provided to give you a better 
understanding of the maintenance 
 
items that should be performed on your 
vehicle. The scheduled maintenance log 
indicates at which mileage/time intervals 
 
each item should be performed. Please  
note that many maintenance items should  
be performed only by a qualified technician.
For further information on maintenance 
items you can perform yourself, see the 
“Maintenance and Care” section of the 
Owner’s Manual.
Automatic Transmission Fluid 
Inspect or replace at specified intervals. 
When performing inspections, check each 
component for signs of leakage. If you 
discover any leakage, have it repaired by  
a qualified technician immediately.
Ball Joints and Dust Covers 
Check the suspension and steering  
linkage ball joints for looseness and  
damage. Check all dust covers for 
deterioration and damage. Replace  
any deteriorated or damaged parts.  
A qualified technician should perform  
these operations.
Brake Lines and Hoses
Visually inspect for proper installation.  
Check for chafing, cracks, deterioration  
and signs of leakage. Replace any 
deteriorated or damaged parts. A qualified 
technician should perform these operations.
Brake Linings/Drums and  
Brake Pads/Discs
Check the brake linings (shoes) and  
drums for scoring, burning, fluid leakage, 
broken parts and excessive wear. Check  
the pads for excessive wear and the discs  
for runout, excessive wear and fluid  
leakage. Replace any deteriorated or  
damaged parts. A qualified technician  
should perform these operations.
Cabin Air Filter
Replace at specified intervals. Driving in  
heavy traffic, on dirt roads or in urban,  
desert or dusty areas may shorten filter’s  
life. More frequent replacement may  
be necessary. 
Page 57 of 68

55Maintenance Log
MAINTENANCE
Drive Shaft Boots
Check the drive shaft boots and clamps for 
cracks, deterioration and damage. Replace 
any deteriorated or damaged parts and, if 
necessary, repack the grease. A qualified 
technician should perform these operations.
Driver’s Floor Mat
•  Only use the driver’s floor mat  
designed specifically for the model  
and model year of your vehicle.
•  Always properly secure the driver’s  
floor mat using the retaining hooks.
•  Never install another floor mat on top  
of the existing driver’s floor mat.
•  Never install the driver’s floor mat  
upside down.
Engine Air Filter
Inspect or replace at specified intervals.  
When performing inspections, check for 
damage, excessive wear and oiliness, and 
replace if necessary.
Engine/Inverter Coolant
Drain the cooling system and refill with an 
ethylene-glycol type coolant. Inspect hoses 
and connections for corrosion and leaks. 
Tighten connections and replace parts  
when necessary. A qualified technician  
should perform these operations. (For  
further details, refer to “Radiator, Condenser 
and Hoses” in the “Maintenance and Care” 
section of the Owner’s Manual).
Your Toyota is equipped with Genuine 
Toyota Super Long-Life Coolant. The 
replacement intervals for engine coolant 
recommended in this booklet are based 
on replacement with Genuine Toyota 
Super Long-Life Coolant or similar 
high-quality non-silicate, non-amine, 
non-borate ethylene-glycol coolant with 
long-life hybrid organic acid technology 
(i.e., a combination of low phosphates 
and organic acids). If another type of  
ethylene-glycol coolant is used, 
replacement intervals may be different. 
EXPLANATION OF MAINTENANCE ITEMS 
Page 58 of 68

56Maintenance Log
MAINTENANCE
EXPLANATION OF MAINTENANCE ITEMS
Engine Oil and Oil Filter
Replace the oil filter and drain and refill 
the engine oil at specified intervals. For 
recommended oil grade and viscosity,  
refer to the Owner’s Manual.
NOTE: Your vehicle is certified with  
Genuine Toyota 0W-16 motor oil. For 
VEHICLES CERTIFIED FOR 0W-16 motor  
oil, the oil change interval is 10,000 miles  
or 12 months IF 0W-16 MOTOR OIL IS  
BEING USED. If 0W-16 is not available,  
0W-20 mineral oil may be used. However,  
it must be replaced at a 5,000-miles or 
six-month INTERVAL with 0W-16 motor oil.
For customers who primarily drive their 
vehicle under any of the listed Special 
Operating Conditions, the motor oil and  
filter should be replaced at 5,000 miles or  
six months, REGARDLESS OF THE OIL USED 
(OR CERTIFICATION OF THE VEHICLE).
Exhaust Pipes and Mountings 
Visually inspect the exhaust pipes, muffler  
and hangers for cracks, deterioration and 
damage. Start the engine and listen  
carefully for any exhaust gas leakage.  
Tighten connections or replace parts  
as necessary.
Fuel Lines and Connections,  
Fuel Tank Band and Fuel Tank 
Vapor Vent System Hoses
Visually inspect for corrosion, damage,  
cracks, and loose or leaking connections. 
Tighten connections or replace parts  
as necessary.
Fuel Tank Cap Gasket
Visually inspect for cracks, deterioration  
and damage and replace if necessary.
HV Battery Cooling Intake Filter
Clean at specified intervals. Refer to “Hybrid 
battery (traction battery) air intake vent and 
filter” in the “Maintenance and care” section  
of the Owner’s Manual for cleaning procedure.
Nuts and Bolts on Chassis  
and Body
Retighten the seat-mounting bolts and  
front /rear suspension member retaining  
bolts to specified torque. 
Radiator, Condenser  
and/or Intercooler
Inspect for debris, corrosion and signs 
of damage. Have any problem repaired 
immediately by a qualified technician.